• The Transactions of the Korean Institute of Power Electronics
• /
• v.22 no.5
• /
• pp.404-413
• /
• 2017

This paper suggests an isolated PFC converter for electric vehicle (EV) chargers with wide-output voltage range. The proposed converter is based on voltage-fed full-bridge structure. All the harmonic and output controls are performed by secondary and primary switches are only operated under a fixed frequency with 50% duty-ratio. In addition, harmonic modulation technique is adopted to obtain a near unity power factor without input current monitoring. The feasibility of the proposed charger has been verified with a 10-kW prototype.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.132-134
• /
• 2007

하이브리드 차량 및 전기차량 구동 모터의 권선저항에 의한 손실 및 모터의 크기를 줄이기 위해 고효율, 고승압형 DC-DC 컨버터 사용이 요구된다. 기존의 부스트 컨버터는 기생저항 성분에 의해 고승압이 불가능하여 변압기를 사용하여 승압비를 향상시킨 current-fed push-pull, current-fed full bridge, dual inductor-fed 부스트 컨버터 등으로 변형되어 사용되어 왔다. dual inductor-fed 부스트 컨버터의 경우 동일조건하에서 앞서 기술된 2가지 컨버터보다 2배의 승압비를 얻을 수 있으며 1차측 전류 스트레스가 낮은 장점을 가지고 있어 대전력, 고승압 응용에 적합하다. 하지만 변압기의 누설인덕턴스에 의한 써지성 전류/전압을 제한하기 위한 부가적인 snubber회로의 사용으로 효율을 떨어뜨리게 되는 단점을 가지고 있다. 본 논문에서는 이러한 단점을 보완할 수 있는 새로운 2개의 인덕터와 1개의 변압기를 갖는 DC-DC 컨버터를 제안한다. 제안된 컨버터의 동작원리와 모드해석을 실시하고 최종적으로 400W, 42Vdc (Battery)/400Vdc (Electric Motor) 실험결과를 통해 이를 검증한다.

• International Journal of Automotive Technology
• /
• v.6 no.2
• /
• pp.141-148
• /
• 2005

In order to reduce the time and costs of improving the performance of vehicle suspensions, the techniques for optimizing damping and air spring characteristic were proposed. A full vehicle model for a bus is constructed with a car body, front and rear suspension linkages, air springs, dampers, tires, and a steering system. An air spring and a damper are modeled with nonlinear characteristics using experimental data and a curve fitting technique. The objective function for ride quality is WRMS (Weighted RMS) of the power spectral density of the vertical acceleration at the driver's seat, middle seat and rear seat. The objective function for handling performance is the RMS (Root Mean Squares) of the roll angle, roll rate, yaw rate, and lateral acceleration at the center of gravity of a body during a lane change. The design variables are determined by damping coefficients, damping exponents and curve fitting parameters of air spring characteristic curves. The Taguchi method is used in order to investigate sensitivity of design variables. Since ride and handling performances are mutually conflicting characteristics, the validity of the developed optimum design procedure is demonstrated by comparing the trends of ride and handling performance indices with respect to the ratio of weighting factors. The global criterion method is proposed to obtain the solution of multi-objective optimization problem.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.201-202
• /
• 2012

This paper presents a simple and cost-effective stand-alone rapid battery charging system of 30kW for electric vehicles. The proposed system mainly consists of active front-end rectifier of neutral point clamped 3-level type and non-isolated bi-directional dc-dc converter of multi-phase interleaved half-bridge topology. The charging system is designed to operate for both lithium-polymer and lithium-ion batteries. The complete charging sequence is made up of three sub-interval operating modes; pre-charging mode, constant-current mode, and constant-voltage mode. Each mode is operated according to battery states: voltage, current and State of Charging (SOC). The proposed system is able to reach the full-charge state within less than 16min for the battery capacity of 8kWh by supplying the charging current of 67A. The optimal discharging algorithm for Vehicle to the Grid (V2G) operation has been adopted to maintain the discharging current of 1C. Owing to the simple and compact power conversion scheme, the proposed solution has superior module-friendly mechanical structure which is absolutely required to realize flexible power expansion capability in a very high-current rapid charging system. Experiment waveforms confirm the proposed functionality of the charging system.

• Journal of the Korean Society for Railway
• /
• v.10 no.3 s.40
• /
• pp.257-263
• /
• 2007

The critical speed above which the vehicle become unstable is one of the items that should be verified in the development of a new train. In the case of a high speed tilting train, which requires both higher critical speed and higher curving speed, the critical speed should be more carefully treated because the both requirements are in conflict with each other in the conventional train design. The main purpose of the present work is to estimate the linear and non-linear critical speeds of 200km/h Korean Tilting Train 'Hanbit200' under development. The newly developed self-steering mechanism was attached to the tilting train to ensure that the critical speed falls under the lower yaw stiffness which is needed to secure higher curving performance. The simulation for predicting the critical speed was done by a commercially available vehicle dynamics software. A full scale roller rig test was carried out to validate the numerical results and to verify the effectiveness of the self-steering mechanism.

• International Journal of Internet, Broadcasting and Communication
• /
• v.13 no.1
• /
• pp.1-10
• /
• 2021

The type approval system for railway vehicle has been in effect since 2016 in order to establish a regular safety management system to secure railway safety and enhance the technological competitiveness of the railway industry, abolished the conventional performance test system through the reform of the Railroad Safety Act in 2012. Until now, there has been appreciated it has been making significant contributions to railway safety and industry of operation and manufacturing companies, taking their place in accordance with the implementation of the system. But there has been no case of quantitative analysis on the effectiveness of the actual system. In this study, in order to examine the full-scale performance of the approval system and quantitatively analyze effectiveness, we identified and defined the relationships with the major elements of the type approval system based on system thinking principle and determined the calculated outcomes to relevant stakeholders. A method of establishing a type approval performance management system that can be grasped, utilized, and adjusted from a point of various stakeholders' views was proposed. This is expected to be more helpful in the implementation of the system, such as improving and applying quantitative effects to analysis by closely reviewing the effects and influencing factors of the type approval system based on the data accumulated through continuous performance management and reflecting to system improvement.

• Journal of Auto-vehicle Safety Association
• /
• v.14 no.4
• /
• pp.113-119
• /
• 2022

The structural safety of hydrogen buses is being evaluated for the successful introduction of hydrogen buses. The crash test methodology, for example, side impact test procedure is being discussed for hydrogen bus structure safety with a compressed hydrogen storage system located under the bus floor. Thus this study describes a new experiment method for side impact test with compressed hydrogen storage system independently based on finite element analysis instead of side impact test using full hydrogen bus. A side crash procedure of conceptual compressed hydrogen storage structure was investigated and impact simulations were performed. The finite element models of hydrogen bus, simplified structures, fuel tank system and side impact moving barrier were set up and simulation results reported model performance and result comparison of three different simplified models. Computational results and research discussion proposed the fundamental test framework for safety assessment of the compressed hydrogen storage system.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11b
• /
• pp.162-169
• /
• 2000

This study was carried out to develop a continuously variable-speed transmission(CVT) for agricultural tractor. A full-toroidal CVT mechanism with four discs and six rollers was selected as a device for changing speed ratio continuously. In the step of system layout design, the sizes of roller cylinders and end-load cylinder, which were critical factors for controlling the variator, were designed. Also the control pressure range was designed to limit the contact pressure of variator. In order to make the maximum speed of vehicle as 30km/h, the planetary gear and the six pairs of gears were designed. Also the hydraulic clutch, silent chain, hydraulic manifold and electronic controller were designed. After the design, a prototype with CVT controller was developed and tested. The speed of vehicle was changed continuously to the speed set by driver and the settling time was about 0.52 second at the step-response test (reduction ratio of variator 2.0 to 1.0), which was acceptable as a response time for working with tractor.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.11B
• /
• pp.1346-1356
• /
• 2011

Transportation has been playing important role in our society by providing for people, freight, and information. However, it cuts its own throat by causing car accidents, traffic congestion, and air pollution. The main cause of these problems is a noticeable growth in the number of vehicles. The easiest way to mitigate these problems is to build new road infrastructures unless resources such as time, money, and space are limited. Therefore, there is a need to manage the existing road infrastructures effectively and safely. In this paper, we propose a road reservation scheme that provides fast and safe response for emergency vehicles using ubiquitous sensor network. Our idea is to allow emergency vehicle to reserve a road on a freeway for arriving to the scene of the accident quickly and safely. We evaluate the performance by three reservation method (No, Hop, and Full) to show that emergency vehicles such as ambulances, fire trucks, or police cars can rapidly and safely reach their destination. Simulation results show that the average speed of road reservation is about 1.09 ~ 1.20 times faster than that of non-reservation at various flow rates. However, road reservation should consider the speed of the emergency vehicle and the road density of the emergency vehicle processing direction, as a result of Hop Reservation and Full Reservation performance comparison analysis. We confirm that road reservation can guarantee safe driving of emergency vehicles without reducing their speed and help to mitigate traffic congestion.

• Journal of Korean Society of Forest Science
• /
• v.82 no.2
• /
• pp.195-206
• /
• 1993

The purpose of this study is to provide a basis for establishing regional harvesting systems that ist the prerequisites for the forest mechanization. The factors restricting to the forest harvesting and logging methods from topographical aspects are studied for this purpose. Three main harvesting methods studied in this paper are : shortwood method, longwood method and full tree method. This study shows : the shortwood method is suitable for low, the longwood method for medium, the full tree method for high topographical conditions. For the logging methods, the focus of the study is on various ground based logging systems by animalpower, manpower, gravitation, wheeled & crawler vehicle and cable. The factors limiting the coverage of logging operation are slope and logging distance. The cable crane logging methods are classified by logging distance into short distance(to 300 or 400m), middle distance(to 700 or 800m) and long distance cable crane methods (over 700 or 800m). The wheeled vehicle method shows serious damages to forest resources, whereas the logging by log-line of the gravitation logging method and cable crane method tend to minimize such damages. The wheeled & crawler vehicle method also shows difficult to apply in the high slope conditions, whereas cable crane method can be applied to maximum 120% steep slope and uphill conditions.