• 한국자동차공학회논문집
• /
• 제14권4호
• /
• pp.20-25
• /
• 2006

Recently, there has been an interest in premixed diesel engines as it has the potential of achieving a more homogeneous and leaner mixture close to TDC compared to conventional diesel engines. Early studies are shown that in a HCCI(Homogeneous Charge Compression Ignition) engine, the fuel injection timing and injection angle affects the mixture formations. Thus the purpose of this study was to investigate relationship of combustion and mixture formations according to injection timing and injection angle in a common rail direct injection type HCCI engine using a early injection method called the PCCI(Premixed Charge Compression Ignition). From this study, we found that the fuel. injection timing and injection angle affect the mixture formations and in turn affects combustion in the PCCI engine.

• 한국분무공학회지
• /
• 제16권4호
• /
• pp.201-209
• /
• 2011

Optimum engine performance is obtained when the spray characteristics is well matched to the geometry of a combustion chamber. Among many parameters governing the combustion performance in internal combustion engine, fuel supply characteristics and atomization are important performance factors. Therefore, spray characteristics of high pressure multi-hole injector has been studied experimentally. An experimental test system has been made to operate high pressure injection system and to visualize spray behavior. Spray visualization has been performed to analyze spray formation, spray cone angle, bent angle and penetration length. Spray interaction with piston has been analyzed with various injector installation angle, injection pressure and ambient pressure. Test results show that penetration length is greatly influenced by the injection pressure. Penetration length is decreased as ambient pressure increased. Spray cone angle is increased as injection pressure and ambient pressure increased. However, bent angle is not influenced by the change of injection pressure and ambient pressure. Spray cone angle distribution map is plotted using the experimental data. Fuel movement around the spark-plug has been enforced as increasing injector installation angle.

• 동력기계공학회지
• /
• 제18권6호
• /
• pp.186-192
• /
• 2014

The spray structures under the stratified and homogeneous charge condition of a gasoline direct injection were investigated in a visualized constant volume chamber. The chamber pressure was controlled from 0.1 MPa to 0.9 MPa by the high pressure nitrogen and the chamber temperatures of $25^{\circ}C$, $60^{\circ}C$ and $80^{\circ}C$ were controlled by the band type heater. The fuel, iso-octane was injected by a 6-hole injector with the pressures of 7 MPa and 12 MPa. From the experiments results, it is confirmed that at lower chamber pressure, the penetration length and spray angle are mainly affected by the chamber temperature with the vaporization of the fuel droplets and generated vortices at the end region of the spray. And at higher chamber pressure, the penetration lengths at the end of the injection were about 50~60% of that at lower chamber pressure regardless of the chamber temperature and the effect of fuel injection pressure is larger than that of the chamber temperature which results from larger penetration lengths at higher fuel injection pressure than at lower fuel injection pressure regardless of the chamber temperatures.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.668-673
• /
• 2000

Spud angle( ${\alpha}$ ) and fuel injection angle ( ${\beta}$ ) have strong influence on spud type gas burner combustion. A wide range of flame stability is shown at ${\alpha}=60^{\circ}$, but at ${\alpha}=30^{\circ}$ is narrow. Optimum condition of flame stability swirl angle( ${\gamma}$ ) is $40^{\circ}$. At condition of ${\alpha}=30^{\circ}$ flame shape is relatively narrow and long, on the other hand, at ${\alpha}=60^{\circ}$ flame is wide and short. Regardless of spud angle, maximum flame temperature shows in the range of Z=200mm and R=0mm. Flame temperature, on the whole, is high at ${\alpha}=45^{\circ}$. At ${\alpha}=45^{\circ}$, NOx emission is higher than other conditions that may be concerned with flame temperature. At ${\beta}=60^{\circ}$ and ${\gamma}=40^{\circ}$, NOx emission is reduced due to fuel injection angle.

• 청정기술
• /
• 제13권4호
• /
• pp.300-307
• /
• 2007

본 연구에서는 연료분출각의 변화에 따라 보염기(cylindrical stabilizer) 후류에 형성되는 확산화염의 화염 안정성, 재순환영역의 길이 및 온도, 보염기 후류의 난류강도 분포, 재순환영역의 연소가스 농도 등을 측정하고, 화염의 직접사진 및 슐리렌사진을 촬영하여 확산화염의 연소특성을 고찰하였다. 화염안정성은 연료분출각과 주류공기 유속의 영향을 받으며, 재순환영역의 길이와 온도는 연료분출각의 영향을 받았다. 재순환영역의 길이가 짧고 온도가 낮을수록 화염안정성이 양호하지만, 연료분출각의 변화에 따른 난류강도 분포에는 별로 차이가 없었다. 재순환영역 내 미연가스 농도가 높고 이산화탄소 농도가 낮은 경우, 화염안정성은 양호하지만 연소상태는 불량한 것으로 나타났다. 연소효율, 고부하 출력, 대기환경, 연료의 청정연소조건 등을 고려하여 적절한 연료분출각을 선정함으로써 양호한 연소조건을 유지할 수 있다.

• 한국분무공학회지
• /
• 제22권1호
• /
• pp.1-7
• /
• 2017

Recently, Performance and fuel efficiency of gasoline engines have been improved by adopting direct injection (DI) system instead of port fuel injection (PFI) system. However, injecting gasoline fuel directly into the cylinder significantly reduces the time available for mixing and evaporation. Consequently, particulate matters(PM) emissions increase. Moreover, as the emission regulations are getting more stringent, not only the mass but also the total number of PM should be reduced to satisfy the Euro VI regulations. Increasing the fuel injection pressure is one of the methods to meet this challenge. In this study, the effects of increased fuel injection pressures on combustion and emission characteristics were experimentally examined at several part load conditions in a 1.6 liter commercial gasoline direct injection engine. The main combustion durations decreased about $2{\sim}3^{\circ}$ in crank angle base by increasing the fuel injection pressure due to enhanced air-fuel mixing characteristics. The exhaust emissions and number concentration distributions of PM with particle sizes were also compared. Due to enhanced combustion characteristics, THC emissions decreased, whereas NOx emissions increased. Also, the number concentrations of PM, larger than 10 nm, also significantly decreased.

• 수산해양기술연구
• /
• 제12권1호
• /
• pp.1-6
• /
• 1976

To investigate the relation of $NO_x$ emission and consumption rate in a direct injection diesel engine with a multihole nozzle under same fuel consumption and rpm, a naphthyl ethylenediaming method on NO, emission and Tektronix oscilloscop on the indicator diagrams have been used. Comparisons of the $NO_x$ emission and fuel consumption rate made on various conditions have led to the fllowing results. 1. The higher the injection pressure in the later injection time the lower $NO_x$ emission and the fuel consumption rate have been attained. 2. By the change of nozzle hole diameter under the same injection pressure, the $NO_x$ emission was much more lowered in the small diameter than large one, but fuel consumption rate was in inverse proption to the $NO_x$ emission. 3. The effect of injection spray angle, $\frac{1_n}{d_n}$ on $NO_x$ emission, fuel consumption rate under same injection time and injection pressure was neglectable.

• 한국분무공학회지
• /
• 제21권2호
• /
• pp.95-103
• /
• 2016

The effect of pilot injection quantity on the combustion and emissions characteristics of a compression ignition engine with a biodiesel-compressed natural gas (CNG) dual fuel combustion (DFC) system is studied in this work. Biodiesel is used as a pilot injection fuel to ignite the main fuel, CNG of DFC. The pilot injection quantity is controlled to investigate the characteristics of combustion and exhaust emissions in a single cylinder diesel engine. The injection pressure and injection timing of pilot fuel are maintained at approximately 120 MPa and BTDC 17 crank angle, respectively. Results show that the indicated mean effective pressure (IMEP) of biodiesel-CNG DFC mode is similar to that of diesel-CNG DFC mode at all load conditions. Combustion stability of biodiesel-CNG DFC mode decreased with increase of engine load, but no notable trend of cycle-to-cycle variations with increase of pilot injection quantity is discovered. The combustion of biodiesel-CNG begins at a retarded crank angle compared to that of diesel-CNG at low load, but it is advanced at high loads. Smoke and NOx of biodiesel-CNG are simultaneously increased with the increase of pilot fuel quantity. Compared to the diesel-CNG DFC, however, smoke and NOx emissions are slightly reduced over all operating conditions. Biodiesel-CNG DFC yields higher $CO_2$ emissions compared to diesel-CNG DFC over all engine conditions. CO and HC emissions for biodiesel-CNG DFC is decreased with the increase of pilot injection quantity.

• 한국분무공학회지
• /
• 제1권1호
• /
• pp.85-91
• /
• 1996

This experiment was undertaken to investigate spray characteristics of the conventional inject ion system and the ultrasonic energy added inject ion system. Sauter mean diameter was mesured under the variation of inject ion pressure and the spray distance. To measure the droplet size we used the Malvern system 2600C. The spray angle and mass distribution was analyzed to the CCD camera and the patternater. After experiment, it was found that the ultrasonic energy added injection system had smaller sauter men diameter of droplet, wider mass distribution and wider spray angle than the conventional inject ion system had.

• 한국자동차공학회논문집
• /
• 제23권2호
• /
• pp.169-177
• /
• 2015

In this study we investigated the regeneration methods for the lean $NO_x$ trap (LNT) catalyst in a 2.2L direct injection diesel engine. The regeneration methods were 1) in-cylinder post fuel injection and 2) external fuel injection strategy. The in-cylinder post fuel injection method uses in-cylinder injectors with the addition of the post fuel injection to supply enough reductants such as CO, $H_2$, THC. The external fuel injection method was enabled by installing a fuel injector with a wide spray angle before the LNT catalyst. Through the engine experiment, the $NO_x$ conversion efficiency, the amount of reductant exhaust gases, fuel consumption, and temperature behavior in the LNT catalyst were evaluated and compared for the two regeneration methods.