• 동력기계공학회지
• /
• 제17권5호
• /
• pp.64-68
• /
• 2013

One of the water management goals in PEM fuel cell is to avoid flooding and drying in the membrane, therefore the air humidification process is required. In order to increase water removal out of the membrane, the water management system may require the dehumidification process and it also requires a large space for application, moreover the process time is slow. In conformity with this fact, this present study proposes an advanced dynamic fuel cell water management which can be an intermittent optimization control using air flow rate instead of the air humidity as an variable in the optimization process. The results of this study have shown that the membrane flooding and drying can be avoided after being assisted by air velocity controlling method.

• 한국산학기술학회논문지
• /
• 제14권5호
• /
• pp.2069-2074
• /
• 2013

내연기관 차량에 전자기식 클러치 워터펌프의 적용은 연비 향상 및 배기가스 저감을 꾀할 수 있다. 이러한 클러치 워터펌프는 엔진 냉각시스템의 유량 단속에 의하여 최적 운전 조건을 가능케 한다. 본 연구에서는 클러치 워터펌프를 이용한 냉각시스템을 제어함으로써 디젤 차량의 연비 및 배기가스 특성을 살펴보았다. 전자기식 클러치 워터펌프에 의한 저온 시동시 냉각수 흐름을 차단하여 아이들 조건에서 예열 시간을 기존 워터펌프 대비 49% 정도 단축시켰고, 주행 중에는 냉각수가 최적 고온상태를 유지하도록 제어하였다. 그리하여 NEDC 모드에서 연소 효율이 개선되어 최대 5% 정도의 연비 향상 효과를 나타내었다. 또한 NOx를 제외한 HC, CO 및 $CO_2$ 배기가스의 농도가 전반적으로 감소하였다.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2004년도 추계학술발표회 발표논문집
• /
• pp.203-204
• /
• 2004

• 조명전기설비학회논문지
• /
• 제24권7호
• /
• pp.9-19
• /
• 2010

Fuel cell (FC) distributed generation (DG) is gradually becoming more attractive to mainstream electricity users as capacity improves and costs decrease. New technologies including inverters are becoming available to provide a uniform standard interconnection of DGs with an electric power system. Some of the operating conflicts and the effect of DG on power quality are addressed and investigated through simulations on a real distribution network with an FC power plant. The results of these simulations have proved load tracking capability following the real and reactive power change of the load and have shown the flow of overcurrent from an FC power plant during the ground fault of a distribution line.

• 한국자동차공학회논문집
• /
• 제6권2호
• /
• pp.32-42
• /
• 1998

Lean burn gasoline engine is recognized as a promising way to meet better fuel economy. Lean burn engine is classified into port injection and direct injection(DI), DI is more active technique for improving fuel economy with ultra-lean operation, Nowadays, port injected lean burn engine has been produced by many Japan maker. Also, DI engine is also possible for production owing to improvement in control technique of spray, flow air fuel ratio. DI engine uses either homogeneous stoichiometric mixture or stratified mixture by controlling injection timing to be early or late respectively. HM(homogeneous mixture) is worse than SM(stratified mixture) in view of ultra-lean operation in partical load and Nox reducion by using EGR control. But, HM has advanteges in cold starting and emission reduction during transient operation, This paper describes experimental variables and bench test results of HM GDI engine.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2007년도 하계학술대회 논문집
• /
• pp.163-165
• /
• 2007

Generally, the power management system of fuel cell hybrid vehicle (FCHV) requires a unidirectional DC/DC converter for the fuel cell (FC) and a bidirectional DC/DC converter for the battery. To manage the various power flows between these modules with a simple way, a new band-gap reference voltage (BGRV) control strategy is proposed. The proposed method easily controls this variable power flow by setting the reference voltages of each converter to slightly different values, and it can be simply implemented by commercial controllers as well. The operational principle of proposed method is presented and verified experimentally by the 400W prototype.

• 한국산업융합학회 논문집
• /
• 제19권4호
• /
• pp.185-192
• /
• 2016

Low operational cost and high efficiency is absolute requirements in the mass production of the ship engine. Increasing the performance of the fuel injection system in the diesel engine is one kind of solution to improve the efficiency. Modern diesel engines are using electronic control module as the main controller in the fuel injection control system, however the mechanical system still involved in the modern control system. In modern ship engine, a control valve was used in injection fuel to regulate the flow of the fuel. High pressure and friction are intensively occur within this part, therefore high wear resist and low friction coefficient material including fine lubricating are needed. This study is to figure out the wear resist material and proper lubricant in the control valve fuel injection. The experiment has been tested using pin on disk in several treatments those are used various lubricants and non-lubricant condition. Two kinds of lubricant were used in this experiment such as INDERIN AW-32 and paraffin oil. INDERIN AW-32 has a better result compared to non-lubricant condition, which are 20% performance increases than non-lubricant condition. SCM 440 was providing small friction coefficient in the lower velocity. The friction coefficient was constantly maintains at 0.1 m/s of velocity or above respectively with the increment of the loads. Using INDERIN AW-32 and paraffin oil the lowest friction coefficient occurred at the lower load, and increases side by side with the increment of loads.

• Journal of Advanced Marine Engineering and Technology
• /
• 제27권2호
• /
• pp.260-271
• /
• 2003

For the Purpose of understanding the mixing phenomena of a GDI(Gasoline Direct Injection) engine, the spray behaviors and fuel distributions were investigated in a single cylinder transparent GDI engine. The experimental engine is a swirl type GDI engine with a SCV(Swirl Control Valve). PLIF(Planar Laser Induced Fluorescence) system with KrF Excimer laser was used for the measurement of the fuel distributions. The effects of SCV opening angles and the injector specifications on the fuel distribution characteristics were investigated. As a result, it was found that the SCV opening angle had a great effect on the fuel distributions in the late stage of compression process by changing the flow fields in the combustion chamber.

• 한국분무공학회지
• /
• 제24권2호
• /
• pp.66-72
• /
• 2019

Diesel vehicles suffer from poor starting and running problems at cold temperatures. Diesel vehicles have the characteristic that CO and PM are reduced or similarly discharged when going from low temperature to high temperature. In this study, a bypass type piezo injector for electronic control based common rail injection system was used. Numerical analysis using injector drive analysis model was performed to analyze injector drive and internal fuel flow characteristics according to fuel temperature change. The results show that the rate of density change due to the fuel temperature is proportional, and that the effect of the kinematic viscosity is relatively large between $-20^{\circ}C$ and $0^{\circ}C$. Comparing the results of temperature condition at $0^{\circ}C$ and $20^{\circ}C$, it is considered that the viscosity is more correlated with the needle displacement than the pressure chamber of the delivery chamber.

• 항공우주기술
• /
• 제11권1호
• /
• pp.84-90
• /
• 2012

연소기용 연료개폐밸브는 파일롯 공압으로 포핏을 열고 스프링 힘에 의해 닫음으로써 로켓엔진의 연료 유량을 제어한다. 현재 개발 중인 연소기 연료개폐밸브는 액추에이터에서 압력이 제거되더라도 유로부에 해당 압력이 존재한다면 스스로 열림을 유지하는 방식으로 설계되어 있다. 밸브의 성능을 평가하기 위해 밸브가 열리고 닫히는 특성에 따라 힘 평형 상태를 분석할 필요가 있다. 이를 위하여 밸브의 포핏이 열리기 위한 파일롯 압력과 닫히기 위한 유로부 압력을 힘 평형에 의해 조절되도록 설계하였다. 또한, 상용 소프트웨어인 Fluent CFD 해석을 통해 밸브의 고유유량계수를 구해보았다. 예측과 해석을 통해 획득된 결과들은 실험 결과와 비교하였다.