• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.12
• /
• pp.1185-1192
• /
• 2012

The typical operating temperature of an automotive fuel cell is lower than that of an internal combustion engine, which necessitates a refined strategy for thermal management. In particular, the performance of the cooling module has to be higher for a fuel cell system because the temperature difference between the fuel cell and the surrounding is lower than in the case of the internal combustion engine. Even though the cooling system of an automotive fuel cell determines the operating temperature and temperature distribution of the fuel cell, it has attracted little research attention. This study presents the mathematical model of a cooling system for an automotive fuel cell system using Matlab/$Simulink^{(R)}$. In particular, a radiator model is developed for design optimization from the development stage to the operating stage for an automotive fuel cell. The cooling system model comprises a fan, pump, and radiator. The pump and fan model have an empirical relation, and the dynamics of the pump and fan are only explained by motor dynamics. The basic design study was conducted, and the geometric setup of the radiator was investigated. When the control logic was applied, the pump senses the coolant inlet temperature and the fan senses the coolant out temperature. Additionally, the cooling module is integrated with the fuel cell system model so that the performance of the cooling module can be investigated under realistic operating conditions.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.88.1-88.1
• /
• 2010

In recent days, the study for the renewable energy is required to supplement traditional energy source. One of the renewable energy of Fuel Cell is classified according to the electrolytes. It is the MCFC (Molten Carbonate Fuel Cell) for this study. One of the equipments of the heat exchangers is important component for efficiency and cost. In MCFC system, several heat exchangers are used according to the application. It is named for the humidifier because it is to preheat the fuel and water so that a reactor will convert some of the incoming fuel to hydrogen. Then, hot side fluid service is used the exhausted gas from the fuel cell and cold side fluid service is the fuel and water. The operation temperature range is about 25~500 Celsius Degree. This heat exchanger has the problems of heat transfer considering to multiphase fluid and phase changing. So it is necessary to analyze the heat transfer characteristics and to propose the reasonable design methodology for the humidifier. In this study, the thermal characteristic for the humidifier is estimated by using commercial tool of heat exchanger design and rating. And this study provides the testing methodology and presents the results for test facility of fabrication and for testing.

• Transactions of the Korean hydrogen and new energy society
• /
• v.30 no.2
• /
• pp.128-135
• /
• 2019

In this study, the mesoporous $SiO_2$ (5, 10, or 15 wt%) was incorporated into the polybenzimidazole matrix in order to improve the proton conduction as well as physiochemical properties of composite membrane. The chemical structure of mesoporous $SiO_2$ and crystallinity of as-prepared membranes were analyzed by Fourier-transform infrared (FT-IR) spectroscopy and X-ray diffraction (XRD) analysis, respectively. The thermal stability of the pristine $X_1Y_9$ and composite membranes were evaluated by thermogravimetric analyzer (TGA). On other side, the physical and chemical properties of the pristine $X_1Y_9$ and composite membranes were also determined by acid uptake and oxidative stability tests, respectively. With the incorporation of 15 wt% $SiO_2$, the composite membrane exhibits the higher proton conductivity that may be applicable for non-humidified high temperature fuel cell applications.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.5
• /
• pp.299-310
• /
• 2009

Fuel cells are expected to be promising future power sources in both aspects of thermal efficiency and environmental friendliness. Accordingly, worldwide research and development efforts have been enormously increasing recently in various applications such as power plants, transportation and portable power sources. Among others, high temperature fuel cells, such as solid oxide fuel cells and molten carbonate fuel cells, are suitable for electric power plants. Moreover, their high operating temperature is quite appropriate to construct further advanced integrated systems. This paper reviews recent literatures on research and development of integrated power generation systems based on high temperature fuel cells. Research and development efforts are summarized in the area of fuel cell/ gas turbine hybrid systems, application of carbon capture technology to fuel cell systems, integration of coal gasification with fuel cells, and the use of alternative fuels.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.235-238
• /
• 2005

Sulfonated poly(ether sulfone) copolymers (PESs) were synthesized using hydroquinone 2-potassium sulfonate (HPS) with other monomers (bisphenol A and 4-fluorophenyl sulfone). PESs with different $mole\%$ of hydrophilic group were prepared by changing the mole ratio of HPS in the polymerization reaction. The chemical structure and the thermal stability of these polymers were characterized by using $^1H-NMR$, FT-IR and TGA techniques. The PES 60 membrane, which has $60 mole\%$ of HPS unit in the polymer backbone, has a proton conductivity of 0.091 S/cm and good insolubility in boiling water. The TGA showed that PES 60 was stable up to $272^{\circ}C$ with a char yield of about $29\%\;at\;900^{\circ}C\;under\;N_2$ atmosphere. To investigate the single cell performance, the catalyst coated PES 60 membrane was used and a single cell test was carried out using $H_2/O_2$ gases as fuel and oxidant at various temperatures. We observed that the cell performance was enhanced by increasing the cell temperature. A current density of $1400 mA/cm^2$ at 0.60 V was obtained at $70^{\circ}C$.

• Membrane Journal
• /
• v.33 no.3
• /
• pp.137-147
• /
• 2023

In this study, Br-PPO was developed by applying additive organic particles through a suspension polymerization synthesis method. The anion exchange membrane fuel cell system performance was evaluated using it to an anion exchange membrane. To improve the performance, organic ion exchange particles were prepared and added to the anion exchange membrane. Chemical structure analysis and synthesis were determined through FT-IR and NMR, and tensile strength and thermal stability were measured through TGA and UTM to determine whether it could be driven. Before the anion exchange membrane fuel cell test, the performance was evaluated by measuring the ion conductivity and ion exchange capacity. Finally, the Br-PPO-TMA-SDV (0.7%) anion exchange membrane with excellent ion conductivity and ion exchange capacity was introduced into the fuel cell system. Its performance was compared with FAA-3-50, a commercial membrane, to determine whether it could be introduced into a fuel cell system.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.410-411
• /
• 2009

The multi-component ceramic proton conductor, $BaZr(Y)O_3-SiO_2-TiO_2-ZrO_2$ (BZY-STZ) and $LaPO_4-SiO_2-TiO_2-ZrO_2$ (LP-STZ), were synthesized by micro-emersion and sol-gel technique. The characterization of proton conductors were carried out using X-ray diffraction(XRD), thermogravimetric analysis(TGA), differential thermal analysis(DTA), impedance analysis. The proton conductors indicate the possibility of application for the intermediate temperature up to $700^{\circ}C$.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2004.05b
• /
• pp.65-68
• /
• 2004

Proton-exchange membranes have attracted much attention in the past few decades due to their important application in fuel cell systems. The mainly used proton-exchange membranes are perfluoropolymers such as DuPont's Nafion$^{(R)}$ and Asahi Chemical's Aciplex$^{(R)}$ because of their high performance including high proton conductivity ＆ mechanical strength, and excellent thermal ＆ chemical stability.(omitted)ted)

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.5
• /
• pp.512-520
• /
• 2017

This paper is a numerical study of various methods of applying SOFC hot BOP insulation. The application methods are four cases from case 1 to case 4, and the performance difference between the result of applying powdered insulation and the result of zoning using composite multi-layer insulation was examined. Numerical results show that the thermal stability of composite multi-layer insulation is better than that of powder insulation when the thermal conductivity is 0.04 W/mK. In the future, we will increase the thermal conductivity of the composite multi-layer thermal insulation material and find the greatest value of thermal conductivity with a similar result to that of the powder insulation.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.127-128
• /
• 2006

Nafion/basic polymer composite membranes were prepared to reduce the methanol crossover for the application of direct methanol fuel cell. The thermal and mechanical properties increased with increasing basic polymer contents due to the formation of complex via acid/basic interaction. The water uptake, proton conductivity, methanol permeability decreased with increasing basic polymer concentration by reduction of acidity associated with the formation of acid/base complex. The molecular effect on those properties was not considerable.