• Korean Chemical Engineering Research
• /
• 제49권5호
• /
• pp.516-520
• /
• 2011

휴대용 고분자전해질 연료전지의 수소발생용으로써 $NaBH_4$는 많은 장점을 갖고 있다. 본 연구에서는 $NaBH_4$ 가수분해 반응의 수소 수율에 대해 연구하였다. $NaBH_4$ 가수분해 반응의 수소 수율에 미치는 촉매 형태, 온도, $NaBH_4$ 농도, NaOH 농도 등의 영향에 대해 실험하였다. 촉매는 Co-P/Cu, Co-B/Cu와 Co-P-B/Cu를 사용하였는데 이들 촉매 종류에 따라 $NaBH_4$ 가수분해 반응의 수소 수율에 미치는 영향은 거의 없었다. $60^{\circ}C$ 이하의 온도에서 $NaBH_4$ 농도가 증가하면 부산물과 $NaBH_4$에 의해 겔이 형성되면서 가수분해 반응의 수소 수율이 감소였다. 겔 형성에 의해서 $NaBH_4$ 가수분해 반응 속도와 수소 총 발생량이 감소하였다. 안정화제인 NaOH를 첨가하면 겔 형성을 촉진해 수소 수율을 감소시켰다.

• 멤브레인
• /
• 제27권5호
• /
• pp.425-433
• /
• 2017

화석연료의 무분별한 사용에 따라 이산화탄소 배출 등 환경오염의 문제가 대두되면서, 전 세계적으로 신 재생에너지 및 친환경 에너지에 많은 연구가 이루어지고 있다. 연료전지는 전기에너지를 발생시키며 부산물로써 물만을 생성하는 친환경 에너지 발전 장치이다. 특히, 음이온 교환막을 이용한 알칼리 연료전지(Anion Exchange Membrane Alkaline Fuel Cell, AEMAFC)는 수소이온 교환막을 이용한 연료전지(Proton Exchange Membrane Fuel Cell, PEMFC)에 비해 보다 높은 촉매의 활성으로 인해 저가의 금속 촉매의 사용이 가능하다는 장점이 있다. 이러한 AEMAFC에서 요구되는 AEM의 특성으로는 연료전지가 작동하는 높은 pH 조건에서 높은 이온전도도 뿐만 아니라 화학적 안정성이다. 본 연구에서는 화학적 안정성을 극대화 시키기 위하여 poly(2,6-dimethyl-1,4-phenylene oxide) 고분자에 spacer-type의 전도기를 도입함과 동시에 가교법을 이용하여 높은 이온전도도($80^{\circ}C$, $67.9mScm^{-1}$)와 기계적 성질(영률 : 0.53 GPa) 뿐만 아니라 높은 pH 조건에서 화학적 안정성($80^{\circ}C$, 1000 h, 6.8% loss of IEC)을 갖는 AEMAFC용 고분자 전해질 막으로써의 가능성을 제시하였다.

• 전력전자학회논문지
• /
• 제26권6호
• /
• pp.404-410
• /
• 2021

This paper proposes a high step-up converter with zero-voltage transition (ZVT) cell for fuel cell electric vehicle. The proposed converter applies a ZVT cell to a dual floating output boost converter (DFOBC) so that not only the main switch but also the ZVT switch can achieve full-range soft switching. The current rating of the ZVT switch is 17% of the main switch. The proposed converter has high reliability in that no timing issue occurs. Therefore, online calculation is not required. The minimum turn-on time of the ZVT switch that guarantees soft switching at all loads and input/output voltage is obtained by analysis. In addition, the proposed DFOBC allows the use of a 650 V device even at 800 V output and has the advantage of being able to boost the voltage by 3.5 times with 0.56 duty. Planar coupled inductor with PCB winding was successfully implemented with the converter operated at 300 kHz. The 25 kW prototype achieves peak efficiency of 99% and power density of 63 kW/L.

• 한국물환경학회지
• /
• 제28권6호
• /
• pp.917-922
• /
• 2012

In order to improve applicability of a microbial fuel cell the laboratory-scaled study has been performed by adopting an air-cathode MFC system with high concentrated anaerobic slugies in this study. The concentrations of microbes are grouped into three types, Type A (TS 1.7%), Type B (TS 1.1%) and Type C (TS 0.51%). The open circuit voltage $(V_{oc})$ characteristics showed that the medium microbes concentration of 1.10% (Type B) kept a constant voltage of 1.0 V for 150 hours, which showed the longest time among three types (Type A and Type C). The discharge charge curves for a closed circuit with $500 \Omega$ also showed that Type B generated a stable discharge voltage of 0.8 V for a longer time as in the open circuit voltage case. This could be explained by the relatively large amount of the attached microbes. Under the $V_{oc}$condition the COD removal efficiency of Type B was found to be low for a long time, but those of Type A and C were found to be high for a short period of time. Therefore, the suspended microbes could decrease the coulombic efficiency. It was concluded that the high $V_{oc}$ was caused by low COD and the $V_{oc}$ became low after the COD removal. The COD reduction resulted in an unstable and low working voltage. From the polarization characteristics Type A was found to show the highest power density of $193\;mW/m^2$ with a fill factor of 0.127 due to the relatively high remaining COD even after the MFC reaction.

• 한국수소및신에너지학회논문집
• /
• 제30권1호
• /
• pp.21-28
• /
• 2019

Reversible solid oxide fuel cell (ReSOC) system was integrated with waste steam for electrical energy storage in distributed energy storage application. Waste steam was utilized as external heat in SOEC mode for higher hydrogen production efficiency. Three system configurations were analyzed to evaluate techno-economic performance. The first system is a simple configuration to minimize the cost of balance of plant. The second system is the more complicated configuration with heat recovery steam generator (HRSG). The third system is featured with HRSG and fuel recirculation by blower. Lumped models were used for system performance analyses. The ReSOC stack was characterized by applying area specific resistance value at fixed operating pressure and temperature. In economical assessment, the levelized costs of energy storage (LCOS) were calculated for three system configurations based on capital investment. The system lifetime was assumed 20 years with ReSOC stack replaced every 5 years, inflation rate of 2%, and capacity factor of 80%. The results showed that the exergy round-trip efficiency of system 1, 2, 3 were 47.9%, 48.8%, and 52.8% respectively. The high round-trip efficiency of third system compared to others is attributed to the remarkable reduction in steam requirement and hydrogen compression power owning to fuel recirculation. The result from economic calculation showed that the LCOS values of system 1, 2, 3 were 3.46 ¢/kWh, 3.43 ¢/kWh, and 3.14 ¢/kWh, respectively. Even though the systems 2 and 3 have expensive HRSG, they showed higher round-trip efficiencies and significant reduction in boiler and hydrogen compressor cost.

• 대한환경공학회지
• /
• 제32권1호
• /
• pp.87-96
• /
• 2010

미생물 연료전지의 전극소재는 전기발생량에 영향을 미치는 중요인자이다. 본 연구에서는 탄소전극의 두께 구조가 미생물 연료전지의 전력밀도 미생물 형성 미생물 군집의 다양성에 미치는 영향에 관해 연구를 수행하였다. 산화 환원 전극조합의 능률적인 구성을 위해 다양한 형태의 탄소전극으로 이루어진 7개 실험실 규모의 반응기가 연속식 공정으로 운전되었다. 반응기의 안정화 상태에서 구멍이 있는 흑연펠트(6 mm 두께) 조합이 전기발생량 238 mV, 그리고 쿨롱효율이 37%로 가장 높은 셀 성능을 나타내었다. 산화전극 표면에 미생물의 생성을 관찰하기 위해 SEM 촬영을 실시한 결과, 니트형태의 탄소섬유와 흑연펠트의 표면에 미생물양의 생성이 증가함을 관찰할 수 있었다. 식종 슬러지와 산화전극 부착성장 미생물의 우점종 변화를 관찰하기 위해 PCR-DGGE를 통한 미생물 군집해석 결과, 식종슬러지내의 미생물 군집과 운전 후 각 전극에 우점화 된 미생물의 군집에는 차이를 보였다. 특히 흑연펠트의 탄소섬유에 전기활성 박테리아로 알려진 eobacter 종이 우점화 된 것을 확인할 수 있었다.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2007년도 추계학술대회 논문집
• /
• pp.319-322
• /
• 2007

In the development of paralleling techniques, Multi-Phase Interleaved(MPI) converter constitutes one of the most promising alternatives reported in the last years. This technique consists of a phase shifting of the control signals of several cells in parallel operating at the same switching frequency. As a result, the aggregated input and output current waveform exhibit lower ripple amplitude and smaller harmonics content than in synchronous or stochastic operation modes. Based on the inherent advantages of the MPI converter, in this paper, a control scheme, which can reduce current and voltage rifle, is proposed for PEMFC generation systems. The MPI boost converter is composed of several identical boost converters connected in parallel.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제54권5호
• /
• pp.238-244
• /
• 2005

This paper proposes a new configuration of 36-pulse voltage source converter which consists of two 6-pulse bridges and a pulse-interleaving auxiliary circuit. The system topology of proposed converter was derived to increase the pulse number of converter output voltage without increasing the number of 6-pulse bridges. The gate pulse generation was analyzed using the theoretical approach of multi-pulse switching converter, The operational feasibility of proposed system was verified by computer simulations with PSCAD/EMTDC software and experimental works with 2kVA hardware prototype. The proposed converter can be widely used for the uninterruptible power supply, the power quality compensator, and the distributed power generation, such as solar and fuel cell power system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 추계학술대회 논문집 전력기술부문
• /
• pp.280-282
• /
• 2002

As EG(Embedded Generation : photo-voltaic, wind, combined heat and power, fuel cell, small hydro etc.) grows fast in adopting to peak load reducing at the middle or the end of distribution system, there much has been interested in interconnection of EG. This paper discusses the various issue of a embedded generator to power system and shows the simulation of its various situation that could happen (focusing on load-flow by EG) by using a commercial software CYME(PSAF) for load-flow. With a result of above simulation, this paper shows a way of possible solution briefly.

• 한국토양비료학회지
• /
• 제45권3호
• /
• pp.410-420
• /
• 2012

The heavy reliance on fossil fuels, especially oil and gas has triggered the global energy crisis. Continued use of petroleum fuels is now widely recognized as unsustainable because of their depleting supplies and degradation to the environment. To become less dependent on fossil fuels, current world is shifting paradigm in energy by developing alternative energy sources mainly through the utilization of renewable energy sources. In particular, bioenergy recovery from wastes with the help of microorganism is viewed as one of the promising ways to mitigate the current global warming crisis as well as to supply global energy. It has been proved that microorganism can generate power by converting organic matter into electricity using microbial fuel cells (MFCs). MFC is a bioelectrochemical device that employs microbes to generate electricity from bio-convertible substrate such as wastewaters including municipal solid waste, industrial, agriculture wastes, and sewage. Sustainability, carbon neutral and generation of renewable energy are some of the major features of MFCs. However, the MFC technology is confronted with a number of issues and challenges such as low power production, high electrode material cost and so on. This paper reviews the recent developments in MFC technology with due consideration of electrode materials used in MFCs. In addition, application of biocathodes in MFCs has been discussed.