• Journal of computational fluids engineering
• /
• v.2 no.1
• /
• pp.54-65
• /
• 1997

Wall wetting in diesel engines has been considered as a bad phenomenon because of fuel deposition which makes fuel/air mixing and evaporation worse. In order to avoid the problem, many research works have been carried out. One of the studies is on new combustion chamber systems which are using spray impacting on a wall. In this study a new type of chamber system is analysed using wall impaction model introduced and assessed in the coupled paper. The gas phase is modelled in terms of the Eulerian continuum conservation equations of mass, momentum, energy and fuel vapour fraction, The liquid phase is modelled following the discrete droplet model approach in Lagrangian form. With various conditions the spray distribution, vapor contour and gas flows are analyzed, and then design factors of those combustion systems are recommended.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.7
• /
• pp.529-535
• /
• 2008

The characteristics of combustion process in an internal combustion engine are affected by the mixing process between injected fuel and ambient gas. Therefore, it is necessary to understand the mixture formation process of diesel spray. In this study, the spray structure was visualized by the exciplex fluorescence method, which can provide the simultaneous 2-D images of vapor and liquid phase in inner spray. For accurate investigation, the liquid-phase images were recorded with a 35mm still camera and CCD camera. Consequentially, it could be confirmed that the high-concentration vapor phase is formed in the region of spray tip and the edge of the liquid phase where droplets exist in the evaporating diesel spray, and the formed vapor is spread by diffusion. Also, the distribution of vapor is determined by the motion of droplets that exist in the edge of the liquid phase and the spray-tip region.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.3
• /
• pp.466-474
• /
• 2004

The characteristics of liquefied butane spray are expected to be different from conventional diesel fuel spray, because a flash boiling spray is expected when the surround pressure is below the saturated vapor pressure of the butane(0.23MPa 98K). The axial velocities. radial velocities. and size distributions in butane sprays were measured with PDPA(Phase Doppler Particle Analyzer) system. Sprays were macroscopically observed by using the high speed camera in case that the surround pressure is 0.37MPa and 0.15MPa. respectively. Compared with the conventional spray. the reversed results were investigated when the surround pressure is below the saturated vapor pressure of the butane.

• Journal of ILASS-Korea
• /
• v.7 no.3
• /
• pp.18-23
• /
• 2002

An evaporating diesel spray of a common rail lnjector was visualized by LIEF technique. This technique makes it possible to separate the vapor and liquid phase images. The experiment was conducted in a constant volume vessel to make a high temperature and high pressure condition. Three images(vapor and liquid phase images from LIEF and a liquid phase image from Mie scattering) were taken simultaneously in one spray event. The major experimental parameters are the injection pressure and the ambient gas pressure. Also, a relative SMD distribution in a liquid phase was obtained by the ratio of the intensities of the fluorescence and the Mie scattering. The results show that the injection pressure and the ambient gas pressure have a close relation with the spray development and air-fuel muting process.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.4
• /
• pp.874-882
• /
• 2017

As the interest on the air-pollution is gradually rising up at home and abroad, automotiv e and fuel researchers have been working on the exhaust emission reduction from vehicles through a lot of approaches, which consist of new engine design, innovative after-treatment systems, using clean (eco-friendly alternative) fuels and fuel quality improvement. This research has brought forward three main issues : evaporative, performance, air pollution. In addition, researcher studied the environment problems of the bio-ethanol, bio-butanol, bio-ETBE (Ethyl Tertiary Butyl Ether), MTBE (Methyl Tert iary Butyl Ether) fuel contained in the fuel as octane number improver. The researchers have many dat a about the health effects of ingestion of octane number improver. However, the data support the con clusion that octane number improver is a potential human carcinogen at high doses. Based on the bio-fuel and octane number improver types (bio-ethanol, bio-butanol, bio-ETBE, MTBE), this paper dis cussed the influence of gasoline fuel properties on the evaporative emission characteristics. Also, this p aper assessed the acceleration and power performance of gasoline vehicle for the bio-fuel property. As a result of the experiment, it was found that all the test fuels meet the domestic exhaust gas standards, and as a result of measurement of the vapor pressure of the test fuels, the bio - ethanol : 15 kPa and the biobutanol : 1.6 kPa. thus when manufacturing E3 fuel, Increasing the biobutanol content reduces evaporation gas and vapor pressure. In addition, Similar accelerating and powering performance was shown for the type of biofuel and when bio-butanol and bio-ethanol were compared accelerated perf ormance was improved by about 3.9% and vehicle power by 0.8%.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.3
• /
• pp.453-465
• /
• 2014

The paper provides a review on bio-oil production technology from biomass by using fast pyrolysis to use heating fuel, power fuel and transport fuel. One of the most promising methods for a small scale conversion of biomass into liquid fuels is fast pyrolysis. In fast pyrolysis, bio-oil is produced by rapidly heating biomass to intermediate temperature ($450{\sim}600^{\circ}C$) in the absence of any external oxygen followed by rapid quenching of the resulting vapor. Bio-oil can be produced in weight yield maximum 75 wt% of the original dry biomass and bio-oils typically contain 60-75% of the initial energy of the biomass. In this study, it is described focusing on the characterization of feedstock, production principle of bio-oil, bio-oil's property and it's application sector.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.253-256
• /
• 2006

A numerical study for spray flow of fuel and oxidizer droplets in the combustion chamber has been conducted prior to the analysis of spray combustion of the liquid rocket engine. As the spray combustion model, DSF model and Euler-Lagrange scheme have been used. While the coupling effects of the droplets between gas phase and evaporated vapor have been calculated using PSIC model, SIMPLER algorithm and QUICK scheme have been used as numerical schemes. As the results, the calculations have shown velocity and temperature distribution in combustion chamber as well as mole fraction of fuel and oxidizer.

• Journal of the Korean Society of Visualization
• /
• v.20 no.2
• /
• pp.38-44
• /
• 2022

Due to increasingly strict emission regulations for carbon-based fuels in the shipping industry, there is a significant motivation to investigate the alternative fuel. Ammonia is one of the attractive alternative fuels as a carbon-free fuel. Since ammonia has different properties such as high vapor pressure and low boiling point compared to conventional fuels, further research into ammonia spray behavior is important. In this work, the spray characteristics of ammonia and other fluids (ethanol, n-decane) were compared by using numerical simulation. The results show that the spray characteristics of ammonia differs from those of the others due to the occurrence of flash boiling. The narrow-dispersed spray with accelerated velocity at the center have been observed for ammonia. It is also found that droplets of ammonia achieve smaller diameter with more uniform distribution, leading to better atomization behavior compared to the others.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.5
• /
• pp.172-180
• /
• 2006

This study was to analyze the effect of mixed fuel composition and mass fraction on the characteristics of evaporating diesel spray and combustion under the various ambient conditions. The characteristics of vaporization distribution and combustion were visualized by laser induced fluorescent method and direct photography. The experiments were conducted in the constant volume vessel and rapid compression expansion machine with optical access. Multi-component fuels mixed i-octane, n-dodecane and n-hexadecane were injected the vessel and rapid compression expansion machine with electronically controlled common rail injector. Experimental results show that fuel vapor formed stratified distribution. And vaporization and diffusion are become actively increasing in mass fraction of low boiling point component. Consequently multi-component fuels were expected to control the evaporating behavior according to their suitable mass fraction.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.5
• /
• pp.707-716
• /
• 2008

The objective of this study was to analyze the effect of mixed fuel composition and mass fraction on spray inner structure in evaporating transient spray under the variant ambient conditions. Spray structure and spatial distribution of liquid phase concentration were investigated using a thin laser sheet illumination technique on the three component mixed fuels. A pulsed Nd:YAG laser was used as a light source. The experiments were conducted in a constant volume vessel with optical access. Fuel was injected into the vessel with electronically controlled common rail injector. Used fuel contains i-octane($C_8H_{18}$), n-dodecane($C_{12}H_{26}$) and n-hexadecane($C_{16}H_{34}$) that were selected as low-, middle- and high-boiling point fuel, respectively. Experimental conditions are 42 MPa, 72 MPa and 112 MPa in injection pressure, $5\;kg/m^3$, $15kg/m^3$ and $30kg/m^3$ in ambient gas density, 300 K, 500 K, 600 K and 700 K in ambient gas temperature, 300 K and 368 K in fuel temperature and different fuel mass fraction. Experimental results indicated that the multi-component fuels made two phase region mixed vapor and liquid so that it would are helpful to improve combustion, for the fuels of high boiling point component could accelerate evaporation very much according as low boiling point fuel was added to high boiling point fuel.