• Journal of ILASS-Korea
• /
• v.17 no.4
• /
• pp.171-177
• /
• 2012

To understand oxygenated fuel characteristics including spray penetration length and spray angle at a real engine ambient pressure condition, DME was injected into a high pressure chamber by a piezo injector common rail system. The piezo injector common rail system was able to apply steady injection pressure, rapid response, and accurate injection quantity. Injection and ambient pressure were varied to confirm a relation with spray form. Using a direct photographing technique, development process of DME spray was captured. DME injection quantity was enlarged linearly as increasing of the injection pressure. In the high pressure chamber, when the injection pressure was enlarged the penetration length and velocity were increased due to a big momentum of fuel particle at the same ambient pressure. When ambient pressure was increased, the DME spray penetration length and velocity were decreased since the high ambient density of nitrogen was acted as a resistance. Although the ambient pressure and injection pressure were varied, each case of spray angle was almost same since the spray angle had a connection of the injector nozzle geometry.

• Journal of Environmental Health Sciences
• /
• v.43 no.1
• /
• pp.55-63
• /
• 2017

Objectives: This study estimated the emission quantity of benzo(a)pyrene(BaP) produced by fuel combustion in the Seosan area, and analyzed the uncertainty regarding the emissions. Methods: It was based on data from a national agency and from public institutions. Emissions were estimated by using national-level guidelines. The total estimated emissions were analyzed by performing Monte Carlo analysis. Results: The full emission quantity of BaP which was discharged by fuel combustion in the Seosan area stood at 1,194.79 g/yr. The point source emissions came to 184.16 g/yr (95% CI; 158.40-209.39). The line source emissions reached 315.33 g/yr (95% CI; 284.99-344.03). The area source emissions accounted for 695.31 g/yr (95% CI; 605.10-793.88). Chemical and compound manufacturing was the highest with 639.13 g/yr (95% CI; 542.95-728.24) in terms of emissions and oil refinery emissions were high with 153.10 g/yr (95% CI; 129.19~177.46). It was found in the Seosan area that the major source of BaP is the manufacturing of chemicals and chemical products. Conclusion: The emission quantity of BaP which was discharged by the fuel combustion in Seosan area reached 1,194.79 g/yr. Research needs to be continued for the definite estimation of emission of BaP henceforth.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2000.05a
• /
• pp.36-44
• /
• 2000

In his study the simulation was carried out by simplifing and modeling dividing into fuel injectioin pump high pressure pipe and fuel injection valve in the fuel injection system of a low speed marine diesel engine. A computer simulation model was developed using the method of characteristics to analyze the unsteady flow in the fuel injection system considering cavitation and variation of fuel density and bulk modulus. Comparison was commenced between the calculated data and experimental data of pressure and injection quantity at the high pressure distributor in fuel injection system for the training ship "M/V hanara" the effects of the high pressure pipe length diameter plunger diameter nozzle openning pressure were also investigated by simulating results.g results.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.6
• /
• pp.43-52
• /
• 2000

In this study, a simulation program was developed, which could simulate a fuel injection system for low-speed marine diesel engine. The fuel injection system was divided into fuel injection pump, high pressure pipe and fuel injection valve. The unsteady flow in the high pressure injection pipe was analyzed by the method of characteristics, considering cavitation and variation of fuel density and bulk modulus. It was confirmed that the simulation results were good agree with experimental results of injection pressure and quantity at the high pressure distributor in fuel injection system for the training ship "M/V Hannara". And the effects of the atomizer hole diameter, maximum needle lift, plunger diameter and nozzle opening pressure were also investigated with simulating results.g results.

• Journal of Advanced Marine Engineering and Technology
• /
• v.12 no.1
• /
• pp.28-36
• /
• 1988

Since the oil shocks of 1970s, the quality of the fuel oil for marine diesel engines has become more degarded than ever. When the poorer quality fuel is burned, carbon residues of the fuel oil cause blockage of the fuel injection valve nozzle and troubles of fuel injection system. The mis-firing of engine occurs due to the decrease of fuel quantity injected, the decrease of compression pressure in the slow speed range, the increase of fuel leaked and the high ignition temperature of degraded fuel etc. This paper is to investigate theoretically the effects of mis-firing on the crankshaft axial vibration of diesel engine. The cylinder pressure in operation is calculated by the computer aided simulation of closed cycle for a large two-stroke diesel engine and also the exciting force of axial vibration and the resonance amplitudes are calculated. And then, the condition of normal state, misfiring and one-cylinder cut-off operation are analyzed. The results of calculations show good agreements with those of the actual measurements.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.4
• /
• pp.1-7
• /
• 2013

DME spray characteristics were investigated about varied ambient pressure and fuel injection pressure using the DME common rail fuel injection system when the nozzle holes diameter is varied. The common rail fuel injection system with DME cooling system was used since DME has properties of compressibility and vaporization in atmospheric temperature. The fuel injection quantity and spray characteristics were measured. The spray analysis parameters were spray shape, penetration length, and spray angle at six nozzle holes. Three types of injector were used, the nozzle holes diameter were 0.166 mm (Injector 1), 0.250 mm (Injector 2), and 0.250 mm with enlargement of orifice hole from 0.6 mm to 1.0 mm (Injector 3). The fuel injection pressure was varied by 5MPa from 35 to 70MPa when the ambient pressure was varied 0, 2.5, and 5MPa. When using Injector 3 in comparison to the others, the DME injection quantity was increased 1.69 ~ 2.02 times. Through this, it had the similar low heat value with diesel which was injected Injector 1. Among three types of injector, Injector 3 had the fastest development velocity of penetration length. In case of spray angle, Injector 2 had the largest spray angle. Through these results, only the way enlargement the nozzle holes diameter is not the solution of DME low heat value problem.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.1
• /
• pp.90-97
• /
• 2016

Sunken vessels accidents have harmful impacts on the marine environment because of oils and chemicals in the vessels. The government has managed them and developed risk assessment which can evaluate potential risk quantitatively since 1999. But the grades of present risk assessment has changed greatly depending on quantity of remaining fuel oils, and the list of remaining fuel oils omitted in status report of sunken vessels. Therefore, the aim of the study is to estimate and develop model for quantity of remaining fuel oils and verify the remaining fuel estimation comparison with active vessels. To accomplish the purpose of the study, apply this verified estimation model to current risk assessment and recommend guideline for an accurate sunken vessels risk assessment.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.3
• /
• pp.37-44
• /
• 2012

In this paper, the application of robust fuel gauge algorithm in the external environment to general fuel gauge system is proposed. The proposed fuel gauge system is composed of two modules which are Moving Average Filter (MAF) and Inclination Filter (IF). They are used to show correctly the amount of fuel in the external environment which are curve road, slope or acceleration/deceleration driving. In parallel, verification and validation processes using Software In the Loop Simulation (SILS) in personal computer and Hardware In the Loop Simulation (HILS) similar to actual vehicle environments are established. Through this research, it turned out to be possible to operation of gauge become correct of external environment.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.19 no.2
• /
• pp.58-63
• /
• 2011

A Continuous Descent Approach(CDA) is defined as a simple, cost-effective, noise and emission abatement technique for any powered aircraft on approach. CDA also can be optimised within energy, speed and safety constraints by avoiding unnecessary flap, air brake and engine thrust. This study includes comparison on fuel consumption between Continuous Descent type and Step Down type by using flight data. In particular, we investigated fuel flow per hour, calibrated airspeed and pressure altitude for all flight time. During descent flight, the fuel consumption of Continuous Descent type was less than the fuel consumption of Step Down type.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.233-236
• /
• 2004

An experimental study was conducted to evaluate characteristic variation of diluted engine oil by diesel fuel and its effects on engine components. Especially, engine oil was made to have $15\%$ fuel content. To predict existing diesel fuel content in engine oil after test was used the viscosity calibration curve. About $54\%$ percent of diesel fuel in diluted engine oil was distillated by various paths related to reciprocating motion of piston and the rest diesel fuel plays an important role for decreasing engine oil viscosity. Test results show that lowered engine ell viscosity by diesel fuel dilution become a reason of increasing engine elements wear, Therefore, this caused the quantity of blow-by gas to increase and main gallery pressure to decrease.