• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.4
• /
• pp.131-137
• /
• 2012

This article is about using the fuel mixed with 10% and 20% bio-ethanol to gasoline for the engine as a way to reduce carbon emission before commercializing future automobiles like fuel cell cars. The fuel mixed with 10% and 20% bio-ethanol showed output equivalent to that of the previous gasoline fuel. CO and $CO_2$ emission was somewhat reduced, but the difference was not significant. And the consumption of the fuel increased slightly. However, bio-ethanol is produced from bio mass growing with the absorption of carbon dioxide, so the total amount of carbon dioxide did not increase according to the result. In NOx, as the use of ethanol increases, the effect of reduction gets greater, and the emission of oxygen showed almost no change compared with gasoline.

• Structural Engineering and Mechanics
• /
• v.16 no.4
• /
• pp.423-440
• /
• 2003

Arbitrary Lagrangian Eulerian finite element methods gain interest for the capability to control mesh geometry independently from material geometry, the ALE methods are used to create a new undistorted mesh for the fluid domain. In this paper we use the ALE technique to solve fuel slosh problem. Fuel slosh is an important design consideration not only for the fuel tank, but also for the structure supporting the fuel tank. "Fuel slosh" can be generated by many ways: abrupt changes in acceleration (braking), as well as abrupt changes in direction (highway exit-ramp). Repetitive motion can also be involved if a "sloshing resonance" is generated. These sloshing events can in turn affect the overall performance of the parent structure. A finite element analysis method has been developed to analyze this complex event. A new ALE formulation for the fluid mesh has been developed to keep the fluid mesh integrity during the motion of the tank. This paper explains the analysis capabilities on a technical level. Following the explanation, the analysis capabilities are validated against theoretical using potential flow for calculating fuel slosh frequency.

• Journal of the Korean Applied Science and Technology
• /
• v.28 no.4
• /
• pp.508-516
• /
• 2011

Hydrotreated biodiesel(HBD) is paraffinic bio-based liquid, with the chemical structure $C_nH_{2n+2}$, originating from vegetable oil(the process can also be applied to animal fat). The oil or fat is treated in a number of process, the most important being hydrogenation, in order to create a bio-based liquid diesel fuel. During the hydrogenation, oxygen is removed from the triglyceride and converted into water. Propane is formed as a by product and can be combusted and used for energy production. HBD can be used in conventional diesel engines, pure or blended with conventional diesel, due to its similar physical properties to diesel. This study reports the quality characteristics with chemical and physical properties as an alternative diesel fuel. Especially, HBD showed higher cetane value and number than FAME, and it is consisted of $C_{15}$ - $C_{18}$ n-paraffinic compounds. We also describes quality characteristics of HBD blends(2, 5, 10, 20, 30, 40, 50 vol%) in automotive diesel. HBD blends(max. 20 vol%) were the limit by the Korean specification due to poor low temperature characteristics.

• Korean Journal of Metals and Materials
• /
• v.48 no.1
• /
• pp.39-48
• /
• 2010

In order to investigate the effects of tempering temperature and heat-treatment path on the microstructural and mechanical properties of ASTM Gr.92 steels, four samples with different tempering temperatures and heat-treatment paths wer prepared. THeree experimental steels showed tempered martensitic microstructures, but the sample tempered at $810^{\circ}C$ was presumed to retain partially untempered martensitic microstructures due to a lower ${\alpha}$+${\gamma}$ phase regime. $M_{23}C_6$, V(C,N), and Nb(C,N) precipitates were observed in all samples. In addition $Cr_2N$ was observed to be precipitated finely and uniformly by isothermal heat-treatment. The lath width and precipitate size in the isothermal heat-treated samples were much smaller than those of the tempered-only specimens. Because of a fine and uniform precipitate, a reduction of lath width would enhance precipitation hardeing, and it was shown that mechanical propertiesincluding the hardness and tensile properties of the steels were improved by isothermal heat-treatment.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.25 no.3
• /
• pp.285-291
• /
• 2022

In order to use the liquid rocket fuel, 1,5-diamino-4-methyltetrazolium azide, [DMT]⁺[N₃]^- and 1,5-diamino-4-methyltetrazolium cyanide, [DMT]⁺[CN]^- were synthesized and prepared the ionic liquid rocket fuel after dissolving the synthesized solid-type energetic chemicals in hydrazine, respectively. The thermal decomposition temperatures(T_d) and densities(d) of the prepared ionic liquid rocket fuels were about 200 ℃ and above 1.0 g/cm³ respectively. The ignition delay times(I_dt) of the ionic liqud rock fuels with [DMT]⁺[N₃]^- and [DMT]⁺[CN]^- were in a range of 26.6 - 82.5 ms and the 44.0 - 98.5 ms, respectively. These results mean that the synthesized tetrazolium salts could be used as an ionic liquid rocket fuels. The viscosities of the ionic liqud rock fuels with [DMT]⁺[N₃]^- and [DMT]⁺[CN]^-, which were dissolved in mixture solution of hydrazine/2-hydroxyethylhydrazine were to be 1.34 - 101 cP, and 1.29 - 80.5 cP, respectively. The synthesized ionic liquid rocket fuels in this study could be used as rocket fuel because the [I_dt(100 ms or less), T_d(150 ℃ or more), d(1.00 g/cm³ or more), and η(40.0~ 100 cP)] were achieved to satisfy the range of the used liquid rocket fuels.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.7 s.250
• /
• pp.682-691
• /
• 2006

This study was conducted to assess the effect of mixed fuel composition and mass fraction on spray inner structure in evaporating transient spray under the various ambient conditions. Spray structure and spatial distribution of liquid phase concentration are investigated using a thin laser sheet illumination technique on the multi-component mixed fuels. A pulsed Ar+ laser was used as a light source. The experiments were conducted in a constant volume vessel with optical access. Fuel was injected into the vessel with electronically controlled common rail injector. Used fuel contain $i-octane(C_8H_{18}),\;n-dodecane(C_{12}H_{26})$ and $n-hexadecane(C_{16}H_{34})$ that are selected as low-, middle- and high-boiling point fuel, respectively. Experimental conditions are 25Mpa, 42MPa, 72MPa and 112MPa in injection pressure, $5kg/m^3,\;15kg/m^3\;and\;20kg/m^3$ in ambient gas density, 400K, 500K, 600K and 700K in ambient gas temperature, 300K and 368K in fuel temperature, and different fuel mass fraction. Experimental results indicate that the more high-boiling point component, the longer the liquid phase it were closely related to fuel physical properties, but injection pressure had no effect on. And there was a high correlation between the liquid phase length and boiling temperature at 75% distillation point.

• Journal of the Korean Society of Safety
• /
• v.27 no.1
• /
• pp.20-25
• /
• 2012

The purpose of the study is to assess the extinguishing concentration of inert gases in engine nacelle fire. The experiment was performed with a two dimensional rectangular bluff body stabilized flames, where the fuel was ejected to counter flow and co-flow against an oxidizer stream. Two inert gases, $CO_2$ and $N_2$, were used for extinguishing agent in the oxidizer and methane was used for fuel. The main experimental parameters were the direction of injecting fuel, the kinds of agent and the velocity ratio between air and fuel streams, which controlled the mixing characteristic near bluff body and the strength of recirculation zone in the downstream. The result shows the flame structure and the mode were strongly dependent with fuel/air ratio and the fuel jet direction. For both flow configurations, the extinguishing concentration of $CO_2$ was smaller than the $N_2$ because of the large heat capacity of $CO_2$. However, the concentration of inert gasesat blowout was much smaller than those in the cup burner and coflow jet diffusion flames, which implies that the extinction mechanism of bluff body stabilized flames was mainly due to the aerodynamic aspect. Compared to co-flow fuel injection, the extinguishing concentration of inert gases under counter flow configuration was lower. The effect of direction might result from the mixing characteristic and strength of recirculation zonearound a bluff body. More details should be investigated for the characteristic of recirculation zone in the wake of bluff body using the LES(Large Eddy Simulation).

• Journal of the Korean Ceramic Society
• /
• v.46 no.6
• /
• pp.574-582
• /
• 2009

$UO_2$ microsphere particles, core material of HTGR(High Temperature Gas Reactor) nuclear fuel, were prepared using by the GSP(Gel Supported Precipitation) method which is a modified-method of the wet sol-gel process. The spherical shape of initial liquid ADU droplets from the vibration nozzle system was continuously kept till the conversion to the final $UO_2$ microsphere. But the size of a final $UO_2$ microsphere was shrunken to about 25% of an initial ADU droplet size. Also, we found that the composition of dried-ADU gel particles was constituted of the very complicated phases, coexisted the U=O, C-H, N-H, N-O, and O-H functional groups by FT-IR. The important factors for obtain the no-crack $UO_2$ microsphere during the thermal treatment processes must perfectly wash out the remained-$NH_4NO_3$ within the ADU gel particle in washing process and the selections of an appropriate heating rate at a suitable gas atmosphere, during the calcining of ADU gel particles, the reducing of $UO_3$ particles, and the sintering of $UO_2$ particles, respectively.

• 한국연소학회:학술대회논문집
• /
• 2006.10a
• /
• pp.260-265
• /
• 2006

An experimental study on the catalytic reformer adopted in the auxiliary power unit system of solid oxide fuel cell was conducted. A 3-fluid nozzle, by which liquid fuel such as diesel, water and air are sprayed and uniformed mixed, was designed and used in this study. An electrically heated monolith inserted in the reformer was used for the vaporization of fuel and water in the transient state of reformer. The reformer uses the partial oxidizing reaction at the catalyst and the supply of water prevents the flame combustion in the spraying zone and lessens the deactivation of catalyst. The result showed that the reforming of liquid fuel can be started by the electrically heated monolith and the 3-fluid nozzle can give the uniform mixing of fuel, water and air. It was also found that the reformer fueled by n-hexadecane can make the reformate, at best, containing $H_2$ at 15.5% and CO at 11.5% that are used as fuel in the solid oxide fuel cell.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1697-1702
• /
• 2003

In this paper, the effect of oxygen component in fuel on the exhaust emissions has been investigated for a direct injection diesel engine. It was tested to estimate change of engine performance and exhaust emission characteristics for the commercial diesel fuel and oxygenated blended fuel which has seven kinds of mixed ratio. And, the effects of exhaust gas recirculation(EGR) on the characteristics of NOx emission have been investigated. Ethylene glycol mono-n-butyl ether(EGBE) contains oxygen component 27% in itself, and it is a kind of effective oxygenated fuel of mono-ether group that the smoke emission of EGBE blended fuel is reduced remarkably compared with commercial diesel fuel, that is, it can supply oxygen component sufficiently at higher loads and speeds in a diesel engine. It was found that simultaneous reduction of smoke and NOx was achieved with oxygenated fuel and cooled EGR method.