• 한국정보통신학회논문지
• /
• 제15권12호
• /
• pp.2582-2589
• /
• 2011

본 논문에서는 차량 OBD-II 인터페이스를 통해 쉽게 확보할 수 있는 차량 진단 정보로부터 차량의 연료 소모량을 예측하는 방법을 제안하였다. 이를 위해 차량으로부터 제공되는 흡입 공기량(MAF), 단기 연료 보정(STFT), 장기 연료 보정 (LTFT) 값이 연료 소모량과 관계가 있다고 가정하고, 흡입 공기량, 단기 연료 보정, 장기 연료 보정을 입력 변수로 하며, 연료 소모량을 출력으로 구성하였다. 차량 OBD-II 인터페이스를 이용하여 획득한 값과 차량관련 전문업체로부터 지원받은 연료 소모량 값의 관계를 연소 반응식으로 구성하였다. 제안한 방식의 유용성을 확인하기 위해 도심 도로 5 Km를 실제 주행테스트를 수행하였고, 제안한 차량 데이터를 이용한 연료 소모량 예측 알고리즘의 성능을 확인하였다.

• Journal of Biosystems Engineering
• /
• 제9권2호
• /
• pp.65-73
• /
• 1984

While most of researches on the performance of high temperature grain dryer have dealt mainly with improving dryer capacity and drying speed during the last twenty years, energy efficiency, in fact, has not been emphasized. Current fuel supplies and energy cost have shifted the emphasis to reducing the energy consumption for grain drying while maintaining dryer capacity and grain quality. Since the energy input for drying is relatively large, the recovery and reuse of at least part of the exhaust energy can significantly reduce the total energy consumption in existing drying systems. Unilization of exhaust heat in grain dryer either through direct recycling or by a thermal coupling in heat exchanger have been subject of a number of investigators. However, very seldom research in Korea has been done in this area. Three drying tests(non-recycling, 0.22 recycle ratio, and 0.76 recycle ratio)were performed to investigate the thermal efficiency and heat loss factors of continuous flow type dryer, and to analyze the effect of recycle ratio (weight of exhaust air recycled/total weight of input air) on the energy requriements for rough rice drying. The test results showed that when the exhaust air was not recycled, the energy lost from furnace was 15.3 percent of input fuel energy, and latent and sensible heat of exhaust air were 61.4 percent and 11.2 percent respectively. The heat which was required in raising grain temperature and stored in dryer was relatively small. As the recycle ratio of exhaust air was increased, the drying rate was suddenly decreased, and thermal efficiency of the kerosene burner was also decreased. Drying test with 0.76 recycle ratio resulted in 12.4% increase in fuel consumption, and 38.4% increase in electric power consumption as compared to the non-recycled drying test. Drying test of 0.22 recycle ratio resulted in 6.8% saving in total energy consumption, 8.0% reduction in fuel consumption, and 2.5% increase in electric power consumption as compared to the non-recycled drying test.

• Journal of Mechanical Science and Technology
• /
• 제18권11호
• /
• pp.2049-2057
• /
• 2004

In this study, the combustion characteristics and durability of a diesel engine using emulsified fuel was investigated. Water was used in oil type emulsified fuel. In order to understand the effect of emulsified fuel in a wide range of engine running conditions, D-13 mode was selected as a test condition, and a durability test was included to understand the long-term effect of water. Combustion pressure in a cylinder, exhaust emissions, specific fuel consumption, sound level and maximum torque were measured. NOx and PM were simultaneously reduced and the specific fuel consumption was increased and decreased at low and high loads, respectively. There was no trouble and any damage on the parts of the cylinder during a 500 hour durability test.

• 한국자동차공학회논문집
• /
• 제8권3호
• /
• pp.65-76
• /
• 2000

To measure the fuel consumption rate of a vehicle, a car is tested on chassis dynamometer following given driving mode. But the fuel consumption rate measured by this method may be somewhat different from that measured in on-road driving conditions. It may be due to not considering road grade in driving modes. In this study, new driving modes which include road grade are proposed, and the simulation program to estimate the real driving fuel consumption rate of a vehicle is developed. On-road car tests to verify the simulation program are carried out and the results of the simulation are analysed and compared with those of the experiments.

• 융복합기술연구소 논문집
• /
• 제3권2호
• /
• pp.57-60
• /
• 2013

The purpose of this study is to analysis of how to calculate fuel efficiency in major development countries (U.S. and Europe) and energy consumption formular derivation of domestic CNG fuel and prove by vehicle test. The formula of fuel consumption is different in mpg(mile per gallon), l/100km, and km/l each countries. CNG fuel has a significant impact on fuel density, composition, and Hydro-Carbon ratio. So, this study how to measurement and calculation procedures of CNG gaseous fueled vehicle energy consumption rate.

• 한국도로학회논문집
• /
• 제12권1호
• /
• pp.55-59
• /
• 2010

높은 차량운행비용(VOC : Vehicle Operating Cost)은 포장도로 복구작업의 주요한 원인이고, 차량운행비용(VOC)은 연료소모량, 오일소모량, 부품교체비용 등으로 구성된다. 이중 연료소모량이 VOC에서 차지하는 비중이 높고, 다른 도로조건에 비해 도로 표면 거칠기가 도로의 노화 정도를 대표적으로 지시하는 값이기 때문에, 본 연구에서는 포장도로의 표면 거칠기(IRI : International Roughness Index) 변화에 따른 차량의 연료소모량 변화를 측정하였다. 차량의 연료분사 인젝터의 전압변화를 측정하여 연료소모량을 계산하였고, 속도는 GPS센서를 사용하여 측정하였다. 본 실험 결과를 이용하여 IRI 변화에 대한 연료소모량의 변화율을 계산할 수 있었다. 계산 결과, 40~100km/h 속도영역에서 중형 및 대형 승용차의 연료소모량(L/100km)은 3.5m/km 정도의 IRI 수준에서 IRI(m/lm) 증가율의 7배 정도로 증가하였고, 60km/h의 속도에서 가장 연비가 우수하였다.

• 동력기계공학회지
• /
• 제19권3호
• /
• pp.29-35
• /
• 2015

Environmental pollution is produced by consumption of fossil fuel, therefore alternative fuels is interested for development of new energy resources and reduction of exhaust emissions for air pollution prevention. Biofuels are produced from new vegetable oil and animal fat, may be used as fuel without change of engine structure in diesel engine. In this paper, the test results on specific fuel consumption, combustion characteristics of neat diesel oil and biodiesel blends(10 vol.% biodiesel and 20 vol.% biodiesel) were presented using four stroke, direct injection diesel engine, especially this biodiesel was produced from biodiesel fuel at our laboratory by ourselves. This study showed that specific fuel consumption is increased slightly, on the other hand cylinder pressure, rate of pressure rise, rate of heat release and soot were decreased slightly in the case of biodiesel blends than neat diesel oil.

• 한국분무공학회지
• /
• 제22권2호
• /
• pp.47-54
• /
• 2017

$CO_2$ emission regulation will be prescribed and main issue in automotive industry. Mostly, vehicle's fuel efficiency deeply related to $CO_2$ emission is regulated by qualified driving test cycle by using chassis dynamometer and exhaust gas analyser. But, real driving fuel consumption rate depends so much on the individual usage profile and where it is being driven: city traffic, road conditions. In this study, vehicle model of fuel consumption rate for ICEV and PHEV was developed through co-simulation with CRUISE model and Simulink based on driving control model. The simulation results of fuel consumption rate were analysed with on-road vehicle data and compared with its official level.

• 한국농공학회지
• /
• 제17권2호
• /
• pp.3763-3771
• /
• 1975

This study was attempted to investigate the changes of specific fuel consumption, compression pressure and power output, consequently to obtain basic data on farm kerosene engine. The samples which are used in this study are a 4 cycle water cooled korosene engine for the use of K6-CT83 power tiller and a 4 cycle air-cooled kerosene engine for the use of G5L-3A water pump. The Korean Industrial Standards (K.S)KS-B 6002 "Test code of small internal combustion engine" was referred in carrying out this study, and its results are as follows. 1. According to load increasing, the speific fuel consumption of the engines generally decreases, however, in case of 10% over-loading it increases. 2. As a result of full load consecutive operation, according to passing of operating time, the amount of wear generally increases, consequently the speific fuel consumption also increases, and inversly the compression pressure decreases. 3. The changes of specific fuel consumption and compression pressure were closely related with time of piston ring exchange, and periodically about 100 hours the engines show the increase of specific fuel consumption and the decrease of compression pressure. 4. After about 300 hours, although the engine had new piston rings, the specific fuel consumption increase, consequently the engine needs boring. In actual use, it is impossible to operate consecutively on full load, therefore the boring time of engine is expected to come later.

• 한국추진공학회지
• /
• 제15권2호
• /
• pp.23-28
• /
• 2011

제트연료변경에 따른 엔진 운용 특성 변화를 살펴보기 위해 JP-8 연료와 JP-S 연료를 사용하여 소형터 보제트엔진의 지상시험 및 고도시험을 수행하였다. 비중이 18% 높은 JP-S 연료에 대한 연료조절시스템 특성은 동일 연료공급명령에 대한 실 연료공급량이 JP-8 연료보다 8% 많이 공급되었다. 시동특성은 연료조절시스템의 명령 대비 공급량의 차이로 인한 점화시점 및 엔진 회전수 가속율 등의 변화를 제외하고는 유사한 특성을 보였다. 정상상태 성능 특성은 순 추력의 일부 구간을 제외하고는 순 추력과 공기유량, 배기가스온도 등 대부분의 엔진 성능 변수가 1% 이내로 유사하였으나 연료소모량만은 연료의 발열량 차이로 인해 최대 5 %이상 차이가 발생하였다. 이를 동일 추력 대비 비 연료소모율로 비교할 때 지상시험에서는 약 1.1~2.6 %, 고공환경시험에서는 5 % 이상 차이가 발생하였다.