• 한국자동차공학회논문집
• /
• 제11권2호
• /
• pp.40-47
• /
• 2003

This paper presents a new evaporative system monitoring method using a virtual HC sensor for an automotive on-board diagnosis. A development was made at providing mathematical expressions from the lambda control information to estimate the HC mass flow purged into the intake manifold from the canister for implementing a virtual HC sensor. The change of the lambda averagevalue reflected the influence of the additional fuel from purging results the sensor estimation of the purged HC amount. Based on this virtual HC sensor, a new evaporative system monitoring method was proposed comparing the amount of purged HC amount with the amount of the HC gas evaporated from the fuel tank and absorbed into the canister. Finally, the method was validated with a simulation using the data logged from the retail car.

• 전기화학회지
• /
• 제6권1호
• /
• pp.68-71
• /
• 2003

전지 성능을 저하시키지 않고 연료극 및 공기극의 귀금속 촉매량을 줄이기 위하여 다층막 전극을 이용한 직접메탄을 연료전지의 성능특성을 조사하였다. 다층막 전극 즉, 연료극과 공기극에 사용된 촉매사용량과 나피온 막의 종류를 변화시키며 최종성능을 측정하였다 본 실험에서 사용된 촉매량은 연료극이 $3-4mg/cm^2$ 공기극이 $1-2mg/cm^2$이다. 본 실험에서는 나피온 115를 사용한 MEA3의 $90^{\circ}C$, 2기압에서 측정 결과 최대 전력밀도인 $230mW/cm^2$를 나타내었다. 이 결과는 현재 시판되고 있는 상용전극과 거의 같은 수준의 성능을 보여주고 있는 반면, 금속 촉매의 양은 기존의 상용전극과 비교하여 약 $50\%$ 정도 감소된 것이다.

• 한국자동차공학회논문집
• /
• 제18권4호
• /
• pp.40-47
• /
• 2010

This study deals with the investigation about the effect of the pilot and split injection strategies on the spray-atomization characteristics of biodiesel fuel derived from a soybean oil. Experimental results were compared with the calculation results obtained from the numerical analysis. Fuel properties of biodiesel according to the variation of the fuel temperature were inserted to the fuel library in the KIVA code. The amount of fuel injection is divided into equal mass for each split and main injection. In this work, the pilot injection strategy can be achieved by the amount of fuel injection shortly before the start of the main injection. A spray tip penetration, radial distance and spray area were measured for the analysis of macroscopic spray characteristics. In addition, the local and overall droplet size distribution were calculated by using KIVA-3V code to study the effect of split and pilot injection on the atomization performance under high ambient pressure. From these studies, the experimental results showed the multiple injection induced the decrease of the spray tip penetration due to the reduction and division of the spray momentum compared to single injection. In the atomization performance, the droplet size increased in the case of the multiple injection a little. Moreover, the SMD slightly increased as the fuel droplets goes through the axial direction. The spray behavior of numerical results were well predicted the experimental multiple spray characteristics of biodiesel fuel.

• 수산경영론집
• /
• 제36권3호
• /
• pp.89-117
• /
• 2005

Currently, the tax - exempted vessel fuel is provided for commercial fishing in order to increase the competitive power of fishery production thorough the National Federation of Fisheries Cooperatives. The National Federation of Fisheries Cooperatives should predict the exact amount of fuel consumption for fishing every year to request the fuel from the government. Unfortunately, there is no sophisticated model to predict the tax - exempted vessel fuel consumption. In 2003, the consumption of the tax- exempted vessel fuel was only $25.1\%$ of the estimation amount by the National Federation of Fisheries Cooperatives. This causes an inefficiency in the petroleum management. Moreover, we need some data such as the annual average fishing hours, fishing days and fishing behavior to adopt a new policy regarding fishing. Up to now, the data have been obtained by survey with response in the fishery field. In the most case, we have a small number of data because we spend so much time and money consuming for collecting fishing data. As a result, the level of confidence of the data is associated with the sample size and normally low. In order to achieve more accurate data, we need to develope an efficient method for collecting fishing data. In this research, we proposed a new method to predict the tax- exempted vessel fuel consumption more exactly. The prediction results from the proposed method has been compared with the results from the current method. According to the results in this research, the method proposed here produced much better accuracy than the current method. In addition, we also proposed in the paper for collecting fishing data of the annual average fishing hours using the tax - exempted vessel fuel consumption and the gasoline consumption of vessel engine. The fishing data obtained by using the method proposed in this research could be much more efficient and accurate because it doesn't need to estimate from survey sample data.

• International Journal of Automotive Technology
• /
• 제6권5호
• /
• pp.437-444
• /
• 2005

Unburned hydrocarbon (UBHC) emissions from gasoline engines remain a primary engineering research and development concern due to stricter emission regulations. Gasoline engines produce more UBHC emissions during cold start and warm-up than during any other stage of operation, because of insufficient fuel-air mixing, particularly in view of the additional fuel enrichment used for early starting. Impingement of fuel droplets on the cylinder wall is a major source of UBHC and a concern for oil dilution. This paper describes an experimental study that was carried out to investigate the distribution and 'footprint' of fuel droplets impinging on the cylinder wall during the intake stroke under engine starting conditions. Injectors having different targeting and atomization characteristics were used in a 4-Valve engine with optical access to the intake port and combustion chamber. The spray and targeting performance were characterized using high-speed visualization and Phase Doppler Interferometry techniques. The fuel droplets impinging on the port, cylinder wall and piston top were characterized using a color imaging technique during simulated engine start-up from room temperature. Highly absorbent filter paper was placed around the circumference of the cylinder liner and on the piston top to collect fuel droplets during the intake strokes. A small amount of colored dye, which dissolves completely in gasoline, was used as the tracer. Color density on the paper, which is correlated with the amount of fuel deposited and its distribution on the cylinder wall, was measured using image analysis. The results show that by comparing the locations of the wetted footprints and their color intensities, the influence of fuel injection and engine conditions can be qualitatively and quantitatively examined. Fast FID measurements of UBHC were also performed on the engine for correlation to the mixture formation results.

• 한국가스학회지
• /
• 제24권1호
• /
• pp.49-55
• /
• 2020

산업용 혹은 발전용 가스터빈에 사용되는 이중 콘형 예혼합 연소기의 다단 연소 특성을 이해하기 위하여 실험적연구를 수행하였다. 이를 위하여 기존에 모두 경사면에 공급되는 연료를 콘부분으로 일부 할애하는 방식으로 다단연소 방식을 구성하였으며 콘에서 분사되는 연료공급은 축방향과 콘 경사면 방향으로 하였다. 다단연소 연소특성을 이해하기 위하여 콘에서의 연료 분사 방향과 연료 분배율 변화에 대한 NOx와 CO의 배출 농도 그리고 벽면 온도분포를 측정하였다. 그 결과 총 연료에 대한 콘으로의 분배율이 3%인 경우 콘에서의 연료 분사방향에 관계없이 노즐내의 예혼합 영역에서 연료가 공기와 균일하게 혼합됨으로서 연소영역의 고온점 감소에 의하여 NOx 배출 농도가 감소된다. 그러나 콘에서 축방향으로 분사되는 연료분배율이 8%로 증가하는 경우 노즐 내부 예혼합 영역으로의 화염 역화로 인하여 NOx의 배출농도가 오히려 증가하게 된다.

• 한국수소및신에너지학회논문집
• /
• 제13권1호
• /
• pp.83-89
• /
• 2002

The goal of this research is to understand the NOx emission in direct injected diesel engine with premixed hydrogen fuel. Hydrogen fuel was supplied into the test engine through the intake pipe. Amount of hydrogen-supplemented fuel was 70 % basis on heating value of the total input fuel. The effects of intake air temperature and exhaust gas recirculation(EGR) on NOx emission were studied. The intake air temperatures were varied from $23^{\circ}C$ to $0^{\circ}C$ by using liquid nitrogen. Also, the exhaust gas was recirculated to the intake manifold and the amount of exhaust gas was controlled by the valve. The major conclusions of this work include: ( i ) nitrogen concentrations in the intake pipe were increased by 30% and cylinder gas temperature was decreased by 24% as the intake air temperature were changed from $23^{\circ}C$ to $0^{\circ}C$; ( ii ) NOx emission per unit heating value of supplied fuel was decreased by 45% with same decrease of intake air temperature; and (iii) NOx emission was decreased by 77% with 30% of EGR ratio. Therefore, it may be concluded that EGR is effective method to lower NOx emission in hydrogen fueled engine.

• 전기학회논문지P
• /
• 제64권4호
• /
• pp.303-307
• /
• 2015

The effects of additive such as $H_2O_2$ in KOH electrolyte solution for the Aluminum/Air fuel cell were investigated with regard to electric power characteristics. The power generated by a Al/Air fuel cell was controlled by the KOH electrolyte solution and $H_2O_2$ depolarizer. Higher cell power was achieved when higher KOH electrolyte concentration and higher $H_2O_2$ depolarizer amount. The maximum power was increased by the increase amount $H_2O_2$ depolarizer, it was found that $H_2O_2$ depolarizer inhibits the generation of hydrogen and the polarization effect was reduced as a result. Internal resistance analysis was employed to elucidate the maximum power variation. Higher internal resistance created internal potential differences that drive current dissipating energy. In order to improve the output characteristics of the Al/Air fuel cell, it is thought to be desirable to increase the KOH electrolyte concentration and increase the $H_2O_2$ addition amounts.

• 한국기계가공학회지
• /
• 제19권11호
• /
• pp.58-63
• /
• 2020

The fuel injection amount and timing along with the ignition timing for the gasoline engine of a racing car were adjusted using an electronic control unit (ECU), and the engine performance was evaluated through an acceleration test. The fuel map for the fuel injection amount and ignition map for the ignition timing were derived. Using the transient throttle control, the air-fuel ratio could be maintained at a constant value even in the case of a sudden throttle operation. In the flat shift, ignition blocking was more effective than fuel blocking. In a 75 m acceleration test, the required duration without and with ECU control was 4.47 s and 3.99 s, respectively. Notably, the acceleration could be improved by approximately 10.7% when the ECU control was implemented.

• 한국해양공학회지
• /
• 제35권6호
• /
• pp.393-402
• /
• 2021

As greenhouse gas emissions from maritime transport are increasing, the International Maritime Organization is continuously working to strengthen emission regulations. Liquefied natural gas (LNG) fuel is less advantageous as a point of CO₂ reduction due to the methane leakage that occurs during the bunkering and operation of marine engines. In this study, greenhouse gas emissions from an LNG-fueled ship were analyzed from the perspective of the life cycle. The amount ofmethane emission during the bunkering and operation procedures with various boil-off gas (BOG) treatment methods and gas engine specifications was analyzed by dynamic simulation. The results were also compared with those of other liquid fuel engines. As a result, small LNG-fueled ships without a BOG treatment facility emitted 32% more greenhouse gas than ships utilizing marine gas oil or heavy fuel oil. To achieve a greenhouse gas reduction via a BOG treatment method, a gas combustion unit or re-liquefaction system must be mounted, which results in a greenhouse gas reduction effect of about 25% and 30%. As a result of comparing the amount of greenhouse gas generated according to the BOG treatment method used with each tank size from the perspective of the operating cycle with the amounts from using existing marine fuels, the BOG treatment method showed superior effects of greenhouse gas reduction.