• 제목/요약/키워드: Frost mass

검색결과 67건 처리시간 0.02초

구동장치 및 열교환기 변경에 따른 냉매가열식 열펌프의 성능특성 (Performance of a Refrigerant Heating Type Heat Pump by Changing of Driving Devices and Heat Exchangers)

  • 박윤철;김상혁;김지영
    • 설비공학논문집
    • /
    • 제20권1호
    • /
    • pp.49-56
    • /
    • 2008
  • When the outdoor air temperature decreased less than the freezing temperature, frost forms at the surface of heat exchangers and it makes the performance degradation of a heat pump system. In this study, a heat pump system has been developed which has a refrigerant heating device as an auxiliarly heating equipment. To reduce power consumptions of the system, a liquid pump, rather than a compressor, was used to drive refrigerant in the heat pump cycle. Ratio of refrigerant mass flow between a refrigerant heating heat exchanger(GHX) and a outdoor plate heat exchanger(PHX) was varied and the system performance was measured and analyzed. As results, when the refrigerant flow rate to the GHX was decreased, the system performance is decreased due to heat absorption capability restriction of the GHX and small variation of the power consumption in the compressor. The effect on the evaporating and condensing pressure by the distribution ratio of the refrigerant to the each heat exchanger is small compare to the effect by the frequency change in the compressor. When the compressor was replaced by the liquid pump, the capacity of the system decreased a little, however the power consumption decrease approximately 80% compare with the power used in the compressor.

산업부산물을 이용한 콘크리트 벤치플룸의 성능평가 (Performance Evaluation of Concrete Bench Flume Using Industrial by Products)

  • 정재호
    • 한국건설순환자원학회논문집
    • /
    • 제11권3호
    • /
    • pp.276-281
    • /
    • 2023
  • 기존 보통포틀랜드시멘트를 사용하여 제작한 수로관은 시멘트의 수화생성물이 산에 취약한 특성으로 인하여 열화가 빠르게 진행되고 내구성이 저하되는 문제점이 발생되고 있다. 따라서 본 연구에서는 다양한 산업에서 발생되는 산업부산물인 고로슬래그와 플라이 애시를 이용하여 수로관을 제작하고 그 특성을 분석하였다. 실험결과 굳지 않은 콘크리트에서 슬럼프는 플라이애시의 볼베어링작용으로 인해 증가되는 경향을 나타내었고, 공기량은 미연탄분으로 인해 감소되어 내동해성에 대한 대책이 필요할 것으로 나타났다. 또한 압축강도는 증기양생을 통해 초기강도가 증가되었고, 슬래그 50 %이상의 배합에서는 OPC와 동등이상의 결과가 나타났다. 내산성결과는 질량감소율이 5 % 미만으로 나타나 내구성에 우수한 성능을 나타내었고, 벤치플룸의 휨파괴하중도 KS기준을 모두 상회하여 상용화가 가능할 것으로 판단된다.

낙동강 하구 만입지의 지형발달 (Geomorphological Development of Embayment Area at the estuary of Nakdong River)

  • 양재혁;조국래
    • 한국지역지리학회지
    • /
    • 제17권6호
    • /
    • pp.649-665
    • /
    • 2011
  • 우리나라 동남해안에 위치하고 있는 낙동강 하구 만입에는 대규모의 충적지형이 발달되어 있다. 외형적으로 이들은 하천과 해양의 상호작용에 의해 형성된 델타의 성격을 보이지만 만입 충적물의 퇴적층후는 일반적인 델타와는 다른 층서적 특징을 나타낸다. 이들의 발달과정을 파악하기 위해 남-북, 동-서 횡단면의 총 108개 지점의 시추 주상도를 검토하고 이 중 53개 지점에 대해서는 층후, 구성물질, 패각의 존재유무, 퇴적상을 도식화하고 연대분석(AMS)을 시도하였다. 지형적 배경, 구성물질의 특징과 규모, 층서적 특징, 연대측정 결과를 고려할 때, 낙동강 하구 만입 충적지는 지구조 운동에 의해 다양한 방향의 산지들이 만입을 형성한 후, 여기에 사면 쇄설성 물질, 하천 퇴적물, 홀로세해진시기의 해양퇴적물($7830{\pm}40BP{\sim}5680{\pm}50BP$)이 시기와 공간을 달리하며 퇴적된 것으로 파악될 수 있다.

  • PDF

승용차의 제상 및 성에 제거 성능 평가를 위한 수치해석적 연구 (Numerical Study on the Performance Assessment for Defrost and De-Icing Modes)

  • 김윤기;양장식;김경천;지호성
    • 대한기계학회논문집B
    • /
    • 제35권2호
    • /
    • pp.161-168
    • /
    • 2011
  • HVAC(Heating, Ventilating, Air Conditioning) 시스템은 승객실 내부의 열환경을 제어하여 쾌적성을 향상시키거나 전면 유리창에 생성된 성에를 제거하여 운전자의 가시영역을 확보하는 등 차량의 성능과 관련된 매우 중요한 기능을 담당한다. 본 연구에서는 CFX 를 사용하여 HVAC 시스템의 기능 중 제상 덕트의 성능과 관련된 수치해석적 연구를 수행하였다. 제상덕트의 해석결과, 출구에서의 유량배분특성 및 유동구조는 일반적인 설계주안점에 부합된 양호한 결과를 얻었다. 외부온도 $-18^{\circ}C$ 하에서 물의 잠열인 $3.37{\times}10^5$[J/kg]을 고려한 상변화 과정을 수치적으로 모사하기 위하여 열용량법을 사용하였고, 시간에 따른 제상패턴 해석을 위해 얼음과 유리의 고체도메인에 대한 추가적인 격자 생성 작업이 필요하였다. 유동해석 결과, 전면유리 근처의 유동구조, 유적선, 온도장 해석결과는 본 연구에서 수행한 제상덕트 모델이 우수한 성능으로 제상기능을 수행할 수 있음을 보였으며, 수치해석적 결과는 실험적 결과와 비교하여 제상패턴이 잘 일치함을 확인하였다. 또한 전면유리 상의 4 개의 지점에서 얻어진 온도, 물분율, 엔탈피의 시간에 따른 변화를 통해 상변화 과정을 정량적으로 파악하였다.

조강형 혼화제에 의한 플라이애시 다량 치환 콘크리트의 품질 향상 (Quality Improvement of High Volume Fly Ash Concrete due to Early Strength Gain Admixture)

  • 한천구;박종호;이정아
    • 한국건설순환자원학회논문집
    • /
    • 제4권4호
    • /
    • pp.117-124
    • /
    • 2009
  • 본 연구에서는 FA 다량 치환 콘크리트의 품질 개선 및 기타 품질 향상을 목적으로 선행 연구에서 개발된 조강형 혼화제(GA)로 FA 다량 치환 콘크리트의 품질 향상 가능성을 평가하였다. 실험은 우선 FA 15%를 치환한 배합에 나프탈렌계 혼화제(이하 NA)를 사용한 것을 Plain으로 하였고, FA 20, 25% 및 30%를 치환한 경우, GA를 사용하여 콘크리트의 제반특성을 Plain과 비교 실험 하였다. 굳지 않은 콘크리트 특성으로 유동성은 GA를 사용할 경우 저하하므로 그 사용량을 증가시켜주어야 하는데, 단 W/B 60%의 경우는 Plain 보다 슬럼프 로스가 약 35~70 mm 감소하여 유리한 것으로 나타났다. 공기량은 FA 사용량 증가에 따라 FA에 포함된 미연소탄분의 AE제 흡착작용에 기인하여 감소함으로서 AE제 사용을 비례적으로 증가시켜 주어야함을 알 수 있었다. 블리딩은 FA 20%에서 블리딩 발생량이 가장 적게 나타나 블리딩 저감 효과를 기대할 수 있었다. 경화 콘크리트의 특성으로 응결시간은 GA를 사용한 경우 Plain과 동등한 수준으로 나타나, 응결 지연현상을 줄일 수 있는 것으로 판단된다. 압축강도는 W/B 및 양생온도와 관계없이 GA를 사용한 경우 Plain과 동등한 강도 발현을 확인 할 수 있었으나, FA 30% 치환한 경우는 사용상에 주의가 필요할 것으로 사료된다. 동결융해 저항성은 Plain보다 초기 값이 작게 나타났으나, 전반적으로 큰 차이가 아니기 때문에 내동해성 문제가 없을 것으로 판단된다. 촉진 중성화는 GA를 사용함에 따라, FA를 다량 사용할 경우 단점으로 지적되는 중성화 취약에 대한 문제는 어느 정도 해결 할 수 있을 것으로 분석되었다.

  • PDF

설비공학 분야의 최근 연구 동향: 2011년 학회지 논문에 대한 종합적 고찰 (Recent Progress in Air-Conditioning and Refrigeration Research: A Review of Papers Published in the Korean Journal of Air-Conditioning and Refrigeration Engineering in 2011)

  • 한화택;이대영;김서영;최종민;백용규;김수민
    • 설비공학논문집
    • /
    • 제24권6호
    • /
    • pp.521-537
    • /
    • 2012
  • This article reviews the papers published in the Korean Journal of Air-Conditioning and Refrigeration Engineering during 2011. It is intended to understand the status of current research in the areas of heating, cooling, ventilation, sanitation, and indoor environments of buildings and plant facilities. Conclusions are as follows. (1) Research trends of thermal and fluid engineering have been surveyed as groups of fluid machinery and fluid flow, thermodynamic cycle, and new and renewable energy. Various topics were presented in the field of fluid machinery and fluid flow. Research issues mainly focused on the rankine cycle in the field of thermodynamic cycle. In the new and renewable energy area, researches were presented on geothermal energy, fuel cell, biogas, reformer, solar water heating system, and metane hydration. (2) Research works on heat transfer area have been reviewed in the categories of heat transfer characteristics, pool boiling and condensing heat transfer, nanofluids and industrial heat exchangers. Researches on heat transfer characteristics included heat transfer above liquid helium surface in a cryostat, methane hydrate formation, heat and mass transfer in a liquid desiccant dehumidifier, thermoelectric air-cooling system, heat transfer in multiple slot impinging jet, and heat transfer enhancement by protrusion-in-dimples. In the area of pool boiling and condensing heat transfer, researches on pool boiling of water in low-fin and turbo-B surfaces, pool boiling of R245a, convective boiling two-phase flow in trapezoidal microchannels, condensing of FC-72 on pin-finned surfaces, and natural circulation vertical evaporator were actively performed. In the area of nanofluids, thermal characteristics of heat pipes using water-based MWCNT nanofluids and the thermal conductivity and viscosity were measured. In the area of industrial heat exchangers, researches on fin-tube heat exchangers for waste gas heat recovery and Chevron type plate heat exchanger were implemented. (3) Refrigeration systems with alternative refrigerants such as $CO_2$, hydrocarbons, and mixed refrigerants were studied. Heating performance improvement of heat pump systems were tried applying supplementary components such as a refrigerant heater or a solar collector. The effects of frost growth were studied on the operation characteristic of refrigeration systems and the energy performance of various defrost methods were evaluated. The current situation of the domestic cold storage facilities was analyzed and the future demand was predicted. (4) In building mechanical system fields, a variety of studies were conducted to achieve effective consumption of heat and maximize efficiency of heat in buildings. Various researches were performed to maximize performance of mechanical devices and optimize the operation of HVAC systems. (5) In the fields of architectural environment and energy, diverse purposes of studies were conducted such as indoor environment, building energy, and renewable energy. In particular, renewable energy and building energy-related researches have mainly been studied as reflecting the global interests. In addition, various researches have been performed for reducing cooling load in a building using spot exhaust air, natural ventilation and energy efficiency systems.

공기조화, 냉동 분야의 최근 연구 동향: 2006년 학회지 논문에 대한 종합적 고찰 (Recent Progress in Air Conditioning and Refrigeration Research: A Review of Papers Published in the Korean Journal of Air-Conditioning and Refrigeration Engineering in 2006)

  • 한화택;신동신;최창호;이대영;김서영;권용일
    • 설비공학논문집
    • /
    • 제20권6호
    • /
    • pp.427-446
    • /
    • 2008
  • A review on the papers published in the Korean Journal of Air-Conditioning and Refrigeration Engineering in 2006 has been accomplished. Focus has been put on current status of research in the aspect of heating, cooling, ventilation, sanitation and building environments. The conclusions are as follows. (1) The research trends of fluid engineering have been surveyed as groups of general fluid flow, fluid machinery and piping, etc. New research topics include micro heat exchanger and siphon cooling device using nano-fluid. Traditional CFD and flow visualization methods were still popular and widely used in research and development. Studies about diffusers and compressors were performed in fluid machinery. Characteristics of flow and heat transfer and piping optimization were studied in piping systems. (2) The papers on heat transfer have been categorized into heat transfer characteristics, heat exchangers, heat pipes, and two-phase heat transfer. The topics on heat transfer characteristics in general include thermal transport in a cryo-chamber, a LCD panel, a dryer, and heat generating electronics. Heat exchangers investigated include pin-tube type, plate type, ventilation air-to-air type, and heat transfer enhancing tubes. The research on a reversible loop heat pipe, the influence of NCG charging mass on heat transport capacity, and the chilling start-up characteristics in a heat pipe were reported. In two-phase heat transfer area, the studies on frost growth, ice slurry formation and liquid spray cooling were presented. The studies on the boiling of R-290 and the application of carbon nanotubes to enhance boiling were noticeable in this research area. (3) Many studies on refrigeration and air conditioning systems were presented on the practical issues of the performance and reliability enhancement. The air conditioning system with multi indoor units caught attention in several research works. The issues on the refrigerant charge and the control algorithm were treated. The systems with alternative refrigerants were also studied. Carbon dioxide, hydrocarbons and their mixtures were considered and the heat transfer correlations were proposed. (4) Due to high oil prices, energy consumption have been attentioned in mechanical building systems. Research works have been reviewed in this field by grouping into the research on heat and cold sources, air conditioning and cleaning research, ventilation and fire research including tunnel ventilation, and piping system research. The papers involve the promotion of efficient or effective use of energy, which helps to save energy and results in reduced environmental pollution and operating cost. (5) Studies on indoor air quality took a great portion in the field of building environments. Various other subjects such as indoor thermal comfort were also investigated through computer simulation, case study, and field experiment. Studies on energy include not only optimization study and economic analysis of building equipments but also usability of renewable energy in geothermal and solar systems.