• 한국자동차공학회논문집
• /
• 제12권2호
• /
• pp.131-138
• /
• 2004

In the proto design stage of a new car, the performances of an occupant protection system can be evaluated by CAE even though the real test should be carried out. The number of the real test is reduced by the exact predictions followed by the appropriate design recommendation. However, the existing researches using CAE in predicting the performances do not consider the uncertainties of parameters. That often leads to inconsistency between test and CAE. In this research, the robust design of a protection system such as airbag and load limiter is suggested considering the frontal crash. The parameter design scheme of the Taguchi method is introduced to obtain the robust design of arbitrary airbag and load limiter. It is performed based on the frontal crash test condition of US-NCAP with an arbitrary passenger car. The variances of the performances such as HIC, chest acceleration and probability of combined injury are calculated by the outer array and the Taylor series expansion. Through the analysis of the Taguchi method, the robust optimum is determined.

• 자동차안전학회지
• /
• 제15권4호
• /
• pp.88-94
• /
• 2023

The seating postures of passengers in the automated driving vehicle are possible in atypical forms such as rear-facing and lying down. It is necessary to improve devices such as airbags and seat belts to protect occupants from injury in accidents of the automated driving vehicle, and collision safety evaluation tests must be newly developed. The purpose of this study is to define representative types of head-on collision accidents to develop collision standards for autonomous vehicles that take into account changes in driving behavior and occupants' postures. 150 frontal collision cases remained by filtering (accident videos, images, AIS 2+, passenger car, etc…) and random sampling from approximately 320,000 accidents claimed by a major insurance company over the past 5 years. The most frequent accident type is a head-on collision between a vehicle going straight and a vehicle turning left from the opposite side, accounting for 54.7% of all accidents, and most of these accidents occur in permissive left turns. The next most common frontal collision is the center-lane violation by drowsy driving and careless driving, accounting for 21.3% of the total. For the two types above, data such as vehicle speed, contact point/area, and PDOF at the moment of impact are obtained through accident reconstruction using PC-Crash. As a result, two types of autonomous vehicle crash safety test scenarios are proposed: (1) a frontal oblique collision test based on the accident types between a straight vehicle and a left-turning vehicle, and (2) a small overlap collision test based on the head-on accidents of center-lane violation.

• 한국정밀공학회지
• /
• 제30권11호
• /
• pp.1179-1185
• /
• 2013

In this study, the design optimization of the automotive side member is performed to maximize the crash energy absorption efficiency per unit weight. Design parameters which seriously influence on the frontal crash performance are selected through the sensitivity analysis using the Plackett-Burman design method. And also the design variables, which are determined from the sensitivity analysis, are optimized by two methods. One is conventional approximate optimization method which uses the statistical design of experiments (DOE) and response surface method (RSM). The other is a methodology derived from previous work by the authors, which is called sequential design of experiments (SDOE), to reduce a trial and error procedure and to find an appropriate condition for using micro-genetic algorithm. The proposed optimization technique shows that the automotive side member structure can be designed considering the frontal crash performance.

• 한국자동차공학회논문집
• /
• 제17권2호
• /
• pp.90-97
• /
• 2009

One of the most important factors that affect a person's risk of injury in a motor vehicle crash is the age of the person. This study investigates the characteristics of crash injuries among young, middle-aged and older drivers and occupants. Based on the comprehensive claim data from automobile insurance from 2000 to 2007, this study examines in great detail the drivers and occupants injury body regions and severity by age in car-to-car frontal crashes. It has been shown that elderly drivers and occupants suffer more injuries at a chest region compared to the middle-aged group. This research calls attention to the need for design to make vehicles more protective for older drivers in car-to car frontal crashes.

• 한국자동차공학회논문집
• /
• 제21권2호
• /
• pp.63-71
• /
• 2013

The estimation of occupant injury risk at crash accident is one of the most important assessments for the vehicle crashworthiness performance. The design of safety devices such as occupant restraining system also depend on the kinematics of occupant and its injury risk. The real world in-depth accident investigation provides detailed and realistic information of vehicle damage and occupant injury as well as the accident conditions. This paper introduces a statistical analysis of NASS/CDS database and domestic accident data to correlate speed change, vehicle damage extend, and occupant injury at frontal crash. The maximum crush extend shows a linear relationship with the effective impact speed. The injury risks of the occupant with and without restraining were also respectively quantified with the crush extend. This result can be effectively used for the emergent rescue of crash victims with automatic crash notification system.

• 한국자동차공학회논문집
• /
• 제10권4호
• /
• pp.234-241
• /
• 2002

In this study, the car crash analysis that simulates the crushing behavior of car forestructure during a frontal impact is carried out. The analysis model for front impact of a car consists of the lumped mass and the spring model. The characteristics value of masses and springs is obtained from the static analysis of a target car. The deceleration-time curve obtained from the simulation are compared with NCAP test data from the NHTSA. They show a good agreement with frontal crash test data. The deceleration-time curve of passenger compartment is classified into 3 stages; beginning stage, middle stage, and last stage. And the behavior of masses at each stage is explained. The effect of stiffness variation on deceleration of passenger compartment is resolved. The maximum loaded peak-time of torque box and dash is the main factor to control the passenger compartment's maximum deceleration.

• 한국자동차공학회논문집
• /
• 제10권1호
• /
• pp.153-161
• /
• 2002

This paper develops a finite element model for crashworthiness analysis ova small-sized bus. The full vehicle finite element model is composed of 31,982 shell elements,599 beam elements,42 bar elements, and 34,204 nodes. The model uses four material models (such as elastic, elastic-plastic(steel), rigid. and elastic-plastic (rubber) material model) of PAM-CRASH. The model uses four contact types to define sliding interfaces in ten areas. A frontal crash test using an actual vehicle with 30mph velocity to a rigid barrier is carried out. Vehicle pulses at lower part of left and right b-pillar are measured, and deformed shapes of frame and driver seat's lower left area are photographed. A frontal crash simulation using the developed full vehicle finite element model is performed with PAM-CRASH installed in super computer SP2. The simulation is performed with the same conditions as the test. The measured vehicle pulses and photographed deformed shapes from the test are compared to ones from the simulation to validate the reliability of the developed model.

• 대한기계학회논문집A
• /
• 제26권8호
• /
• pp.1577-1584
• /
• 2002

This paper develops a finite element model for studying the occupant behavior and injury cofficients of a large-sized cab-over type truck. Since it does not have a room to absorb collision energy and deformation in front of the passenger compartment the deformation is directly transmitted to the passenger compartment. Moreover, since its steering column is attached on the frame, severe deformation of the frame directly affects on the steering wheel's movement. Therefore, if the occupant behavior and injury coefficients analysis is performed using a finite element model developed based on a sled test, it is very difficult to expect acquiring satisfactory results. Thus, the finite element model developing in this paper is based on the frontal crash test in order to overcome the inherent problems of the sled test based model commonly used in the passenger car. The occupant behavior and injury coefficients analysis is performed using PAM-CRASH installed in super-computer SP2. In order to validate the reliability of the developed finite element model, a frontal crash test is carried out according to a test method used fur developing truck occupant's secondary safety system in european community and japan. That is, test vehicle's collision direction is vertical to the rigid barrier and collision velocity is 45kph. Thus, measured vehicle pulses at the lower parts of the left and right B-pilla., dummy chest and head deceleration profiles, HIC(head injury criterial) and CA(chest acceleration) values, and dummy behavior from the frontal crash test are compared to the analysis results to validate reliability of the developed model.

• 대한인간공학회지
• /
• 제13권1호
• /
• pp.15-25
• /
• 1994

Based on Fatal Accident Reporting System (FARS) data, safety belt effect- tiveness in preventing fatalities is investigated for the following five types of crashes: frontal, left, rear, right, and rollover. Passenger cars containing two occupants, a driver and a right front passenger, are included in this analysis. For each crash type, these cars containing the two occupants are classified into four categories according to the safety belt usage categories for the two front seat occupants, namely, both belted, both unbelted, and either one was belted but not both. Relative risks of driver and right front passenger fatalities are compared among these four cases. For each crash type, two independent estimates of safety belt effectiveness are obtained for drivers and for right front passengers. The weighted average of the two estimates is calculated for drivers and for right front passengers for the five crash types. Using FARS data starting 1978 throught 1983, safety belts are more effective in rollover accidents than in frontal collisions. In rollover accidents, safety belt effectiveness estimate for drivers is $68%{\pm} 6% $ and that for right front passengers is $71%{\pm}6% $ , in which the error limits indicate one standard error. Sfety belt effectiveness estimates for drivers and right front passengers involved in frontal collisions are $41%{\pm} 9% $ and $37%{\pm} 10% $ , respectively. For left and right sided collisions and for both drivers and right-front-passengers, none of the four estimates are significantly different from 0%, statistically : however, when left and right sided collisions are combined with far sided occupants(drivers involved in right sided collisions and right front passengers involved in left sided collisions) safety belt effectiveness is significant, $38%{\pm} 12% $ . For rear collisions, the estimate for drivers shows statistically significant positive effect, $60%{\pm}23% $ . while for right-front-passengers the estimate is not significantly different from 0%. These results show that a safety belt is an effective restraint system not only in frontal crashes but also in a variety of crashes.

• 대한의용생체공학회:의공학회지
• /
• 제24권1호
• /
• pp.15-21
• /
• 2003

본 연구에서는 경량휠체어 탑승자의 차량 전방충돌시 안전성 평가를 위하여 동적 슬래드 충격실험을 하였다. 실험은 총 6회 시행하였으며 충격속도는 20g/48 $\pm$2km/h 였고, Hybrid III 50%ile 성인남자 인체모형을 사용하여 두부손상기준(Head Injury Criteria), 목의 굴전모멘트, 축 인장력, 전단력, 흉부 가속도. 두부, 휠체어, 무릎의 전방 쏠림량을 측정하였으며 미국자동차학회 규격인 SAE J2249에서 제안한 동작기준 (Motion Criteria)과 미국 제너럴모터스사의 자체기준(GM-IARV)인 복합상해기준(Combined Injury Criteria)을 이용하여 안전성평가를 하였다. 실험결과는 경량 휠체어 탑승자의 전방 충돌 시 최대 상해치를 100%로 봤을 때 휠체어와 탑승자 거동의 위험도지수 MC는 52%, 탑승자의 상체 위험도지수 CIC는 60.1% 였다.