• Tribology and Lubricants
• /
• 제36권3호
• /
• pp.168-192
• /
• 2020

In recently designed diesel engines, the running conditions for piston-pin bearings have become severe because of the higher combustion pressure and increased temperature. Moreover, the metal removal from the bushing material has strongly reduced the ability of the antifriction material to accept asperity contacts. Therefore, it is necessary to find ways of reducing wear scar on the connecting-rod small-end bushing and piston-pin boss bearing related to the higher combustion pressure on the power cell of an engine. In this work, the position and level of material removal from the surfaces of the bushing and bearing under such severe operating conditions - for example, maximum power and torque conditions of a passenger car diesel engine - are estimated for several combinations of surface roughness. First, piston-pin rotating motion is investigated by calculating the friction coefficient at piston-pin bearings, the oil film thickness, and the frictional torques induced by hydrodynamic shear stress. Subsequently, the wear scarring on the surfaces of a connecting-rod small-end bushing and two piston-pin boss bearings related to piston-pin rotational motion is numerically calculated under the maximum power and torque operating conditions. This work is helpful to determine the reasonable surface roughness of the bushing and bearing for reducing wear volume occurring at the interface between a bearing and a shaft.

• Tribology and Lubricants
• /
• 제35권6호
• /
• pp.376-381
• /
• 2019

Surface texturing is widely applied to reduce friction and improve the reliability of machine elements. Despite extensive theoretical studies to date, most research has been limited to parallel thrust bearings, mechanical face seals, piston rings, etc. However, most sliding bearings have a convergent film shape in the sliding direction and the hydrodynamic pressure is mainly generated by the wedge action. The results of surface texturing on inclined slider bearings are largely insufficient. This paper is the first part of a recent study focusing on the effect of the groove position on the lubrication performances of inclined slider bearings. We model a slider bearing with one rectangular groove on a fixed pad and analyze the continuity and Navier-Stokes equations using a commercial computational fluid dynamics (CFD) code, FLUENT. The results show that the film convergence ratio and the groove position have a significant influence on the pressure and velocity distributions. There are groove positions to maximize the supporting load with the film convergence ratio and the groove reduces the frictional force acting on the slider. Therefore, the proper groove position not only improves the load-carrying capacity of the slider bearings but also reduces its frictional loss. The present results apply to various surface-textured sliding bearings and can lead to further studies.

• 한국농공학회논문집
• /
• 제48권3호
• /
• pp.73-82
• /
• 2006

Wind energy is one of the promising renewable energies that could provide electricity and other mechanical power. Wind energy market is dramatically growing in many European countries, but wind power is only 0.2% of the total renewable energy uses that is only about 2% of the primary energy consumption in Korea. It is widely accepted that wind resources fur power generation are only limited in some areas including coastal regions and mountainous areas in Gangwon province in Korea, particularly in terms of large scale wind power developments. In this study, wind velocity data were analyzed with respect to the potential utilization. The data provided from National Weather Service were used for the analysis. In addition, field wind data were also collected and analyzed for the comparison between the national data. The comparison showed that there were significant differences between the experimental station and the national station that are about 5km away. Annual average wind speed at the experimental station was less than 2 m/s, which is not enough fur wind power generation. It seemed that the topographic condition resulted in a significant difference in wind speed. When 600 W and 2.5 kW wind turbines were used, annual power productions were only 186 kWh and 598 kWh, respectively. When the average wind speed is lower, wind pumping is an alternative use of wind. At the experimental station, the average pumping rate of $3m^3/h$ at the head of 3 m was expected at a 2.5 m rotor under the conditions that efficiencies of the rotor and the pump were 40% and 80%, respectively. It did not seem that the wind pumping was not applicable at the station either. A higher wind speed was required to install the wind machines. Meanwhile, wind pumping would be applicable in conditions with lower pumping heads. Other applications were introduced far further wind energy utilization, including wind powered ventilation and friction heat generation in greenhouses.

• 에너지공학
• /
• 제7권2호
• /
• pp.202-208
• /
• 1998

원자력 발전소의 증기방출계통에는 상당수의 산업공정에서 보여지는 바와 같이 배관을 통해 응축성 기체를 침수 분사시켜 응축시키는 과정이 포함된다. 본 연구에서는 증기방출계통 파이프와 지지문의 설계에 사용되는 동적 하중을 계산하기 위하여 증기방출 과도현상에 대한 해석을 특성기법을 사용하여 수행하였다. 해석모델은 마찰이 존재하는 균일한 배관을 통해 증기가 수조로 방출되는 경우에 대하여, 증기유량 및 배관 내에 원래 존재하고 있는 공기와 물의 방출유량 등을 고려하였고 압력 및 열원, 밸브, 분지관 등을 포함하였다. 배관의 유동 특성과 동적 하중을 계통 압력, 배관 길이 및 침수 깊이의 변화에 따라 계산하였다. 계산 결과 공기와 물의 경계에서의 배관의 동적 하중, 배관 내의 물 제거 시간 및 물 이동 속도 등은 계통 압력뿐만 아니라 배관 길이 및 침수 깊이의 영향을 받는 것으로 확인되었다.

• 환경영향평가
• /
• 제15권4호
• /
• pp.237-247
• /
• 2006

In case of studied area located around the sea, the data measured from the regional meteorological office is highly different from the local weather data because the diffusivity of fugitive dust varies considerably with meteorological conditions. Especially, it is very difficult to predict the amount of fugitive dust accurately as wind speed remains high frequently. In this study, the fluxes of suspended particulates as a function of the friction velocity were applied to consider the effect of wind speed on the amount of fugitive dust generated from the reclamation site. The amount of fugitive dust estimated as mentioned above was simulated by using ISCST3 model. As a result, in case of using only the Fugitive Dust Formula which is usually used in Environment Impact Assessment, the predicted $PM_{10}$ concentrations with points were $43.4{\sim}67.8{\mu}g/m^3$. However, in case of applying to the flux of suspended particulates, the predicted values of $PM_{10}$ with points were $43.3{\sim}69.1{\mu}g/m^3$, $49.5{\sim}90.4{\mu}g/m^3$ and $76.0{\sim}182.6{\mu}g/m^3$ with the wind speeds of 4.4, 5.8 and 7.7m/s, respectively. It could be possible to predict the amount of fugitive dust accurately because these predicted values were similar to the measured values. Consequently, we can establish alternatives for reduction of fugitive dust in this area damaged by fugitive dust which is caused by wind.

• Advances in concrete construction
• /
• 제10권4호
• /
• pp.357-367
• /
• 2020

The impulse of this paper is to examine the influence of unsteady flow comprising of Eyring-Powell nanofluid over a stretched surface. This work aims to explore efficient transfer of heat in Eyring-Powell nanofluid with bio-convection. Nanofluids possess significant features that have aroused various investigators because of their utilization in industrial and nanotechnology. The influence of including motile microorganism is to stabilize the nanoparticle suspensions develop by the mixed influence of magnetic field and buoyancy force. This research paper reveals the detailed information about the linearly compressed Magnetohydrodynamics boundary layer flux of two dimensional Eyring-Powell nanofluid through disposed surface area due to the existence of microorganism with inclusion the influence of non- linear thermal radiation, energy activation and bio-convection. The liquid is likely to allow conduction and thickness of the liquid is supposed to show variation exponentially. By using appropriate similarity type transforms, the nonlinear PDE's are converted into dimensionless ODE's. The results of ODE's are finally concluded by employing (HAM) Homotopy Analysis approach. The influence of relevant parameters on concentration, temperature, velocity and motile microorganism density are studied by the use of graphs and tables. We acquire skin friction, local Nusselt and motil microorganism number for various parameters.

• 한국산학기술학회논문지
• /
• 제19권7호
• /
• pp.72-80
• /
• 2018

과학 및 공학 분야 등에서 유한체적법등과 같은 전산해석방법은 비약적으로 발전하여 주로 대학 연구실 및 기업 등에서 활용하고 있었으나 최근에는 대학의 교육과정에서도 전산해석방법이 도입되고 있다. 이것을 계기로 공학대학의 기계공학과등에서 전산유체동역학이 학부 3학년 또는 4학년에 개설되고 있다. 일반적으로 전산유체동역학에서 다루는 수치해석 예제는 상용 전산유체동역학 소프트웨어 회사에서 개발한 예제이다. 따라서 학부 학생들은 저학년에서 학습한 유체역학의 이론적 해와 전산유체동역학 강의에서 학습하는 수치해석 해를 서로 비교할 수 없는 상황이 되고 있다. 따라서 본 연구에서는 유체동역학의 고전적인 해석 대상인인 정상 상태의 수평 원관 층류 유동의 이론적 배경을 설명한 뒤 ANSYS FLUENT를 이용하여 정상 상태의 수평 원관 층류 유동에 대한 수치해석 해를 구하여 이론적 해와 수치해석 해를 서로 비교하여 학생들의 전산유체동역학에 대한 개념을 확실히 다짐으로서 학생들의 현장적응능력을 높였으며 해당 강좌에 대한 강의 평가 결과 학생들이 전산유체동역학에 대한 이해력과 tutorial에 대한 만족도가 매우 높았다.

• 한국지반공학회지:지반
• /
• 제14권4호
• /
• pp.5-16
• /
• 1998

대구지역의 제반은 주로 쇄설성 퇴적암인 혈암으로 구성되어 있다. 이 혈암은 비균질, 비등방성 암석으로 각종 물성치와 역학적 특성이 층리면의 각도($\beta$값)에 따라 매우 다르다. 본 연구에서는 대구지역의 혈암에 대하여 각종 물성, 역학특성 시험을 실시하여 다음과 같은 결과를 얻었다. 비중값은 $\beta$값이 커질수록 감소하지만 간극률, 흡수율은 이와 반대로 증가 하였다. 탄성파 속도는 ($\beta$값이 $90^{\circ}$ 일때가 가장 끈 간을 보이고 탄성계수는$\beta$같이 $30^{\circ}$에서 최대치를 나타내었다. 그리고 강도혹성과 강도정수인 점착력과 마찰각은 모두 $\beta$값이 $60^{\circ}$에서 가장 작은 값을 나타내었다.

• 대한토목학회논문집
• /
• 제14권6호
• /
• pp.1365-1373
• /
• 1994

난류전단 흐름에서의 기포 크기분포를 예측하기 위하여 개발된 Monte-Carlo 모의모형을 실험실 크기의 문제에 적용하였다. 각종 모형 매개변수 및 물리적 변수들에 대한 민감도 분석을 수행하였으며, 실험 관측치와의 비교를 통하여 모형의 실제 적용성에 관하여 조사하였다. 공기와 물의 유량비 또는 마찰계수가 증가함에 따라 기포의 크기가 커지는 것으로 나타났다. 평균유속이 증가함에 따라 가포의 크기는 작아지지만, 폭기구간내 기포의 총표면적은 거의 일정함을 보였다. 모형의 종방향 거리증분에 따른 기포 크기분포의 변화는 거의 없었으며, 횡방향 거리중분을 크게 할수록 기포가 크거나 작은 쪽으로 치우쳐 중간정도의 크기를 갖는 기포의 수가 감소하였다. 기포의 크기분포는 그 초기분포 및 공기의 주입위치에 크게 영향을 받는 것으로 나타났다. 기포의 충돌과 응집을 구분하기 위하여 충돌효율을 도입하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.158-161
• /
• 2003

Recently, the evolution in production techniques (e.g. high-speed milling), the complex shapes involved in modem production design, and the ever increasing pressure for higher productivity demand a drastic improvement of the dynamic behavior of the machine tool axes used in production machinery. And also machine tools of multi functional and minimized parts are increasingly required as demand of higher accurate in some fields such as electronic and optical components etc. The accuracy and the productivity of machined parts are natural to depend on the linear system of machine tools. The complex workpiece surfaces encountered in present-day products and generated by CAD systems are to be transformed into tool paths for machine tools. The more complex these tool paths and the higher the speed requirements, the higher the acceleration requirements are needed to the machine tool axes and the motion control system, and the more difficult it is to meet the requirements. The traditional indirect drive design for high speed machine tools, which consists of a rotary motor with a ball-screw transmission to the slide, is limited in speed, acceleration, and accuracy. The direct drive design of machine tool axes. which is based on linear motors and which recently appeared on the market. is a viable candidate to meet the ever increasing demands, because of these advantages such as no backlash, less friction, no mechanical limitations on acceleration and velocity and mechanical simplicity. Therefore performance tests were carried out to machine tool axes based on linear motor. Especially, dynamic characteristics were investigated through circular test.