• 한국항공우주학회지
• /
• 제31권1호
• /
• pp.25-33
• /
• 2003

일방향-평직 복합재 혼합 적층판의 체결부 파손하중 및 파손모우드를 결정하기 위한 실험과 유한요소해석을 수행하였다. 체결부 실험은 끝단거리 대 원공직경의 비 및 시편 폭과 원공직경의 비가 다른 총 9가지의 모델에 대하여 편하중을 가하여 수행하였다. 체결부 파손해석을 위한 방법의 검토를 위해, MSC/NASTRAN을 사용하여 핀과 모재의 접촉 및 마찰을 고려한 비선형 해석을 수행하였다. 파손여부는 특성곡선 상에서 Tsai-Wu 방법과 Yamada-Sun 방법을 사용하여 평가하였다. 적층판의 체결부 파손하중 및 파손모우드는 원공 중심에서 끝단까지의 거리가 작거나, 시편의 폭이 작을 경우 파손하중에 큰 영향을 미치지만, 일정값 이상이 되면 파손하중과 파손모우드의 변화는 거의 없는 것으로 밝혀졌다. 특성길이 방법에 의한 유한요소해석은 대체로 파손하중과 파손모우드를 비교적 잘 예측하는 것을 볼 수 있었다.

• 대한치과보철학회지
• /
• 제52권4호
• /
• pp.359-365
• /
• 2014

치아가 얼마 남지 않은 부분 무치악 환자들에 있어 이중관(Double crown)을 이용한 치료의 성공적인 결과에 대해서 여러 문헌에서 보고 되고 있다. 이중관 가철성국소의치(Double crown removal partial denture)는 잔존치의 치주적인 상태가 좋지 않은 환자에게 치료의 대안이 될 수 있다. 이중관 가철성 국소의치는 특히 치주상태가 좋지 않고, 임플란트를 식립하기에는 의과적으로 문제가 있는 환자(Medically compromised patient)에게는 수술에 대한 부담 없이 치료할 수 있어 심리적이고 경제적인 이점이 존재한다. 본 증례에서는 상악은 다수의 치아가 잔존하여 고정성 보철물로 수복이 가능한 상태였고, 하악은 소수 잔존치만 남아있고 치주 상태가 매우 불량하여 잔존치를 이용한 클라스프 가철성 국소의치로는 수복하는 것이 거의 불가능하였다. 또한 환자는 1년 전에 하악 전치부 부위의 골수염으로 인한 수술병력으로 임플란트 식립이 어려운 상황이었다. 이러한 악조건에서 하악의 소수 잔존치를 이용한 이중관 의치는 2년이상의 기간동안 기능적, 심미적인 면에서 만족스러운 결과를 얻었기에 이를 보고하고자 한다.

• Composites Research
• /
• 제16권3호
• /
• pp.75-84
• /
• 2003

본 연구의 목적은 가압주조법에 의해 제조된 Saffil/Al, Saffil/$\textrm{Al}_2\textrm{O}_3$/Al, Saffil/SiC/Al 과 같은 혼합금속 복합재료의 마모 물성을 조사하고자 하는 것이다. 마모 시험은 건조와 윤활상태 하에서 pin-on-disk 형태의 마모 시험기로 수행되었다. 세가지 금속복합재료의 마모 물성시험에서 Saffil섬유, $\textrm{Al}_2\textrm{O}_3$입자, SiC입자의 효과들을 조사하였다. 마모 메커니즘은 복합재료의 마모된 표면들을 관찰하여 분석하였다. 마모과정 동안 마찰계수(COF)의 변화는 컴퓨터에서 자동적으로 기록되었으며, 건조 조건에서 Saffi1/SiC/Al은 고온과 높은 하중 하에서 가장 좋은 마모 저항을 보여주었다. 한편 Saffil/ Al과 Saffi1/$\textrm{Al}_2\textrm{O}_3$/Al의 마모 저항은 비슷한 결과를 보였다. 건조조건에서 적당한 하중과 상온에서 지배적인 마모 메커니즘은 연삭 마모이며, 하중이나 온도가 증가함에 따라 응착마모로 변화되며, 고온에서는 융착마모를 나타내었다. 건조 상태에서 세가지 복합재료를 비교시 액체 파라핀에 의한 윤활시험시 마모 특성이 가장 좋은 결과를 나타내었다. 윤활조건에서는 Saffil/Al복합재료가 가장 좋은 마모 저항성을 보였으며, 이 경우 마찰계수도 가장 작게 나타났다. 윤활 조건에서 금속복합재료의 주요 마모 메커니즘은 microploughing 이었으나, microcracking 역시 다른 정도에서는 미소 균열도 발생한다.

• 대한치과보철학회지
• /
• 제59권2호
• /
• pp.201-209
• /
• 2021

가철성 국소의치 치료 시 유지력을 얻는 방법에 따라 많은 연구와 임상적인 적용이 이루어 지고 있다. 그중 한 종류인 이중관 의치는 독일과 스웨덴과 같은 유럽의 나라에서 널리 사용되어지고 있다. 텔레스코픽 이중관 국소의치는 구강 위생관리의 편의성, 지대치로 교합력의 수직적인 전달, 그리고 지대치들 간의 2차적인 고정과 같은 장점들이 있어 클라스프 유지형 가철성 국소의치에 비해 임상적으로 더 나은 결과를 보여줄 수 있다. 본 증례에서 처음에 환자는 자연치를 이용하여 상악에 프릭션핀을 이용한 하이브리드 텔레스코픽 이중관 의치를 제작하였습니다. 7년 뒤 환자의 불량한 구강위생관리 습관과 정기검진의 부재로 지대치들에 치주염이 발생하였고 5개중 4개의 자연치 지대치를 발치하게 되었다. 남은 1개의 자연치 지대치의 내관을 그대로 사용하면서 3개의 추가적인 임플란트를 식립하였다. 대합치인 하악이 고정성 보철임에도 불구하고 전략적인 임플란트 식립으로 인해 환자는 새롭게 제작된 상악 치아-임플란트 연합 이중관 의치에 적응하였고 만족하였다.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.347-351
• /
• 2004

[ $Si_3N_4$ ] composites have been extensively studied for engineering ceramics, because it has excellent room and high temperature strength, wear resistance properties, good resistance to oxidation, and good thermal and chemical stability. In the present work, carbon short fiber reinforced $Si_3N_4$ ceramics were fabricated by hot press method in $N_2$ atmosphere at $1800^{\circ}C$ using $Al_2O_3\;and\;Y_2O_3$ as sintering additives. Content of carbon short fiber was $0\%,\;0.1\%\;and\;0.3\%$. The composites were evaluated in terms of density, flexural strength and elastic modulus through the 3-point bending test at room temperature. Also, The wear behavior was determined by the pin on disk wear tester using silicon nitride ball. Experimental density and flexural strength decreased with increasing content of carbon fiber. But specific modulus increased with increasing content of carbon fiber. In addition, friction coefficient and specific wear loss decreased with increasing content of carbon short fiber by reason of interfacial defects between matrix and fiber.

• Corrosion Science and Technology
• /
• 제17권2호
• /
• pp.68-73
• /
• 2018

Substitution of hip and knee joints by CoCr alloys is in great demand due to their high wear resistance and good biocompatibility. Understanding of tribocorrosion in joint replacements requires study of variables such as coefficient of friction and the choice of a proper corrosive medium in wear-corrosion tests carried out in the lab. The objective of this study was to characterize tribocorrosion behaviour of CoCr alloy with low (LCCoCr) and high carbon (HCCoCr) contents in several corrosive media: NaCl, Phosphate Buffer Solution (PBS), and PBS with hyaluronic acid (PBS-HA). Tribocorrosion tests were carried out on a pin-on-disk tribometer with an integrated electrochemical cell. A normal load of 5N was applied on the alumina ball counterpart at a rotation rate of 120 rpm. Coefficient of friction (COF) was measured and tribocorrosion behaviour was characterized by in situ application of electrochemical techniques. HCCoCr alloy immersed in PBS-HA showed the best tribocorrosion behaviour with the lowest COF. In this case, in situ measurement of corrosion potential and the impedance data under wear corrosion process showed an active state while passive film was continuously destroyed without possibility of regeneration.

• Tribology and Lubricants
• /
• 제36권4호
• /
• pp.199-206
• /
• 2020

CoCr-based alloys have been developed as wear-resistant materials owing to their excellent mechanical properties and strong wear resistance. The purpose of this study is to experimentally assess the frictional and wear characteristics of CoCr-based alloys slid against two different counter materials subjected to various normal forces to determine the expansion applicability of CoCr-based alloys. CoCrMo and CoCr alloys were selected as the target materials and NiCr and NiCrB alloys as counter materials. Experimental tests were performed using a pin-on-reciprocating plate tribo-tester under dry lubrication. Before performing the tests, the surface of the specimens was observed through confocal microscopy and the hardness was measured using a micro-Vickers hardness tester. The wear volume of the plate was calculated at the end of the tests using confocal microscope data, and the wear rate was quantitatively obtained based on Archard's wear law. From the results, the wear rates of the CoCrMo specimens that slid against NiCr and NiCrB are 7.69 × 10^-6 ㎣/Nm and 5.26 × 10^-6 ㎣/Nm, respectively. The wear rates of the CoCr specimens that slid against NiCr and NiCrB were higher than those of the CoCrMo specimens by factors of approximately 4 and 8, respectively. The CoCrMo specimens further exhibited lower friction characteristics than the CoCr specimens. The findings of this study will be useful for expanded applications of CoCr-based alloys as wear-resistant materials for various mechanical parts.

• 한국재료학회지
• /
• 제20권4호
• /
• pp.194-198
• /
• 2010

Cubic boron nitride (c-BN) is a promising material for use in many potential applications because of its outstanding physical properties such as high thermal stability, high abrasive wear resistance, and super hardness. Even though 316L austenitic stainless steel (STS) has poor wear resistance causing it to be toxic in the body due to wear and material chips, 316L STS has been used for implant biomaterials in orthopedics due to its good corrosion resistance and mechanical properties. Therefore, in the present study, c-BN films with a $B_4C$ layer were applied to a 316L STS specimen in order to improve its wear resistance. The deposition of the c-BN films was performed using an r.f. (13.56 MHz) magnetron sputtering system with a $B_4C$ target. The coating layers were characterized using XPS and SEM, and the mechanical properties were investigated using a nanoindenter. The friction coefficient of the c-BN coated 316L STS steel was obtained using a pin-on-disk according to the ASTM G163-99. The thickness of the obtained c-BN and $B_4C$ were about 220 nm and 630 nm, respectively. The high resolution XPS spectra analysis of B1s and N1s revealed that the c-BN film was mainly composed of $sp^3$ BN bonds. The hardness and elastic modulus of the c-BN measured by the nanoindenter were 46.8 GPa and 345.7 GPa, respectively. The friction coefficient of the c-BN coated 316L STS was decreased from 3.5 to 1.6. The wear property of the c-BN coated 316L STS was enhanced by a factor of two.

• Tribology and Lubricants
• /
• 제34권2호
• /
• pp.49-54
• /
• 2018

Hydraulic reciprocating seal has been widely used to prevent fluid leakage in hydraulic systems. Also, hydraulic reciprocating seal plays a significant role to provide lubricant film at contacting interface to minimize tribological problems due to sliding with counter material. To predict lifetime of hydraulic reciprocating seal, quantitative understanding of wear characteristics with respect to operating conditions such as normal force and sliding speed is needed. In this work, effect of sliding speed on wear of polyurethane (PU) hydraulic reciprocating seal were experimentally investigated using a pin-on-disk tribo-tester. The wear characteristics of PU specimens were quantitatively determined by comparing the confocal microscope data before and after test. It was found that the wear rate of PU specimens decreased from $4.9{\times}10^{-11}mm^3$ to $1.1{\times}10^{-11}mm^3/Nm$ as sliding speed increased from 120 mm/s to 940 mm/s. Also, it was observed that the friction decreased slightly as the sliding speed increased. Improvement of lubrication state with increasing sliding speed was likely to be responsible for this enhanced friction and wear characteristics. This result also suggests that decrease in sliding distance between PU elastomer and counter materials at lower sliding speed is preferred. Furthermore, the quantitative assessment of wear characteristics of PU specimen may be useful in prediction of lifetime of PU hydraulic reciprocating seal if the allowed degree of wear for failure of the seal is provided.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.397-397
• /
• 2007

Diamondlike carbon (DLC) coatings were deposited on alumina ceramic seals using a plasma immersion ion deposition technique (PIID). Then they were subjected to tribological tests using a pin-on-disc tribometer under a high load (1.3 GPa) and under elevated temperatures up to 400C. Coefficients of friction (COFs) were recorded and compared with that of the untreated alumina while the wear tracks were analyzed using SEM with EDS to characterize the DLC films. To enhance the DLC adhesion to the substrate, various interlayers including Si and Cr were deposited using the PIID process or an ion beam assisted deposition (IBAD) method. It was observed that the DLC coating, if adhering well to the substrate, reduced the COFs significantly, from 0.4-0.8 for the uncoated alumina to about 0.05-0.1, within the tested temperature range. The adhesion was determined by the interlayer type and possibly by the application method. Cr interlayer did not perform as well as the Si interlayer. This could also be due to the fact that the Cr interlayer and the subsequent DLC coating had to be done in two different processing systems, while both the Si interlayer and the subsequent DLC film were deposited in one system without breaking the chamber. The coating failure mode was found to be delamination between the Cr and the alumina substrate. In contrast, the Si interlayer with proper DLC deposition procedures resulted in very good adhesion and hence excellent tribological performance. Further study may lead to future DLC applications of ceramic seals.