• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2001.09a
• /
• pp.356-363
• /
• 2001

The friction pendulum type seismic isolation system (FPS) using the PTFE based materials has been developed to provide a simple and effective way to achieve earthquake resistance for buildings. PTFE matrials are soft and apt to be deformed easily after a few working cycles. Instead of the usual PTFE materials, the Polyimide material was used in this research. Polyimide is harder than PTFE, but has smaller friction coefficient and longer duration fur usage. In this paper, various kinds of PTFE materials were tested to define the frictional characteristics compared with the Polyimide material. FPS was manufactured with fine surface roughness and used with Polyimide material to show the seismic isolation efficiency, and life duration when applied to a rigid mass model and a 5 stole frame model.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.1
• /
• pp.47-54
• /
• 2004

The friction drag reduction of a ship is of prime importance for the design and production of high-valued/high-tech ship. Thus, this study carried out the development of reliable numerical tools to identify the friction drag reduction mechanism for turbulent boundary layer on the ship surface and to deduce the optimum reduction technique by numerical experiment. The developed LES and DNS numerical tools were applied to simulate the turbulent channel flow These results were very well matched with previous results not only qualitatively but also quantitatively. The parallelization using MPI (Message Passing Interface) technique implemented in the developed code to speed up the simulation and to obtain the accurate results from the fine grid system was testified its computational efficiency.

• Journal of Ocean Engineering and Technology
• /
• v.13 no.2 s.32
• /
• pp.66-73
• /
• 1999

This paper presents the experimental examinations and statistical quantitative analysis of the correlation between the cumulative counts of acoustic emission(AE) during plastic deformation periods of the welding and the tensile strength and other properties of the tube-to-tube welded joints of O.D. 30mm (I.D 18mm) nozzle steel. This is a new approach which attempts finally to develop real-time quality monitoring system for friction welding. And this study results in practical possiblility of real-time quality control more than 100% joint efficiency showing good weld no micro structural defects.

• Journal of Ocean Engineering and Technology
• /
• v.13 no.1 s.31
• /
• pp.88-93
• /
• 1999

This paper presents the experimental examinations and statistical quantitative analysis of the correlation between the cumulative counts of acoustic emission(AE) during plastic deformation periods of the welding and the tensile strength and other properties of the bar-to-bar welded joints of O.D. 16mm shaft(SM40C) as well as the various welding variables. And this is a new approach which attempts finally to develop real-time quality monitoring system for friction welding. The results lead to a practical possibility of real-time quality control more than 100% joint efficiency showing good weld with no micro structural defects.

• Design & Manufacturing
• /
• v.10 no.2
• /
• pp.12-17
• /
• 2016

Recently, lightweight material is attracting attention as a solution to the problem of fuel efficiency and increasing the need for development. CFRP has been attracting attention as lightweight materials for automobile because it has a high specific stiffness and specific strength compared to steel material. CFRP have a wide range of mechanical properties depending on the laminate condition. In this paper, study on the forming analysis of double-dome model was performed considering CFRP prepreg laminate condition and coefficient of friction. After forming analysis, the result has compared with wrinkling area and vertical strain of fiber to the laminated condition. And then compared with inflow of blank to the laminate condition. Through this paper, we propose the forming analysis methods of CFRP material.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.155-161
• /
• 2000

To improve the vehicle fuel economy, various technologies such as improvement of power train efficiency, use of light weight material, improvement of aerodynamic design, have been studied. One of the possible way to improve the vehicle fuel economy is to reduce the engine friction loss by improving the engine oil characteristics. In the present paper, it was examined the effect of the engine oil viscosity and the addition of friction modifier to engine oil on vehicle fuel economy improvements. Moreover, the effect of engine oil degradation on vehicle fuel economy was examined with two gasoline vehicles and one diesel vehicle by using the fuel economy test facility.

• Journal of Welding and Joining
• /
• v.22 no.3
• /
• pp.56-61
• /
• 2004

Friction stir weldability of AZ31B Mg alloy was studied using microstructural observation and mechanical tests. Defect free joints was obtained under the condition of 2000rpm-100mm/min. In TMAZ, a lot of twin deformation were observed due to the mechanical effect of the FSW tool and thus relatively high hardness was obtained. In SZ, the twin deformation was disappeared by recovery and the hardness decreased because the. grain structure was coarsened by dynamic recrystallization and grain growth. The Al-Mn precipitates were observed throughout the joint regions. On the other hand, $$\beta$-Mg_{17}Al_{12}$ intermetallic compounds were not observed in either of the zone. The joint efficiency was about 80% and the impact value of the joint was almost equal to that of base metal.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.6
• /
• pp.412-421
• /
• 2023

As the demand for mechatronic systems and high performance increases in the machinery industry, the importance of improving friction characteristics is emphasized. During relative movement of objects, friction and wear occur on two surfaces in contact, and various methods are being designed to increase the lifespan and energy efficiency of machines. The energy increase effect using lubricants is a well-known method. In this study, a micro-sized rectangular grid pattern was produced by applying a precise micro-pattern photo lithography process. Rectangular grid patterns of the same shape and friction behavior according to the size of the pattern were produced in convex and concave shapes, and the tribological characteristics of each were analyzed.

• The Journal of Korea Robotics Society
• /
• v.13 no.2
• /
• pp.86-91
• /
• 2018

This paper presents about design efforts of a human-sized quadruped robot leg for high energy efficiency, and verifications. One of the representative index of the energy efficiency is the Cost of Transport (COT), but increased in the energy or work done is not calculated in COT. In this reason, the input to the output energy efficiency should be also considered as a very important term. By designing the robot with customized motor housing, small rotational inertia, and low gear ratio to reduce friction, high energy efficiency was achieved. Squatting motion of one leg was performed and simulation results were compared to the experimental results for validation. The developed 50 kg robot can lift the weight up to 200 kg, and during squatting, it showed high energy efficiency. The robot showed 71% input to output energy efficiency in positive work. Peak current during squatting only appears to be 0.3 A.

• Journal of the Korean Geotechnical Society
• /
• v.35 no.8
• /
• pp.31-42
• /
• 2019

A total of 73 pile design data for prebored PHC piles was analyzed to study the current design method. Based on the design data, a ratio of skin friction to total capacity from the pile design data was about 20~53%. Such low ratio of skin friction to total capacity tends to underestimate skin friction. Considering this tendency, the current design method should be improved. Also, an average design efficiency of PHC pile capacity was 70% and an average design efficiency for bearing capacity of soil or weathered rock was 80%, which shows slightly higher value than the former. This is probably due to the fact that the allowable bearing capacity is estimated to be equal to or slightly higher than the design load. Hence, the allowable bearing capacity should be estimated to be higher than the long-term allowable compressive force of the PHC pile. In the current design method, skin friction is calculated to be about 2.2 times lower than end bearing. The current design method for prebored PHC piles applied foreign design methods without any verification of applicability to the domestic soil or rock condition. Therefore, the current design method for prebored PHC piles should be improved.