• 한국생산제조학회지
• /
• 제21권6호
• /
• pp.932-937
• /
• 2012

In the presented study, SM45C carbon steel parts were joined by friction welding. The welding process was carried out under optimized conditions using statistical approach. The study of SM45C is conducted with various combinations of process parameters. Parameter optimization, microstructure and mechanical property correlation are the major contribution of the study. The welded joints were produced by varying spindle revolution speed, friction pressure, upset pressure and burn-off length. Tension tests were applied to welded parts to obtain the strength of the joints. Fracturs properties were additionally obtained experimentally under fluctuated tensile loads. Microstructures using microphotographs were examined in the weld interface and weld region and heat affected zone and base metal and flash zone of welded parts. Finally, Hardness variations in welding zone and base metal were also obtained. Through these tests, the optimum conditions of parameters for ${\phi}20$ SM45C in friction welding were obtained when the friction spindle revolution was 1,950 rpm, the friction pressures was 30 MPs, upset pressures was 50 MPs.

• Journal of Welding and Joining
• /
• 제4권3호
• /
• pp.32-42
• /
• 1986

In this study, the influence of carbon equivalents on friction welds of dissimilar steels was investigated. Four types of carbon steels with 10mm diameter were welded to a high-speed tool steel SKH 9. Main experimental results could be summarized as follows (1) Under constant friction pressure, the friction time increased almost linearly with the increasing burn-off length, while the forge length decreased almost linearly. (2) The maximum hardness in carbon steels increased almost linearly with the increasing carbon equivalent, but was much lower than that in the high speed steel. (3) After quenching and tempering of dissimilar steel friction welds, the hardness in carbon steel weldments became similar as that in the base metal, while the hardness in SKH 9 weld was still higher that of the base metal. (4) Relative movement in the friction phae occurred not at the interface of the weldments, but in the high speed steed steel near the interface. (5) For considered material combinations and welding parameters, most of fractures in tension and twisting tests occurred in the base metal. And welds with so high strength could produced in a wide range of welding parameters.

• Journal of Welding and Joining
• /
• 제8권1호
• /
• pp.43-53
• /
• 1990

The transient temperature distribution in the continuous friction welding 304 stainless steel bars is investigated by experimental and analytical methods. It is calculated by F.D.M. (finite difference method). The heating pressure, the rotational speed and friction coefficient obtained from experiment are used to determine the heat input at the contacting surface. Thermal properties of the workpiece are the function of temperature. The calculated temperature is well coincided with the measured value. The grain size at weld interface is extremely small due to the severe plastic deformation at high temperature, and result of this refined zone reveals higher hardness value. Because the HAZ is very narror about 2-3 mm, welding defects do not occure.

• 소성∙가공
• /
• 제33권3호
• /
• pp.193-199
• /
• 2024

The friction welding characteristics of stainless steels, mainly used in energy and chemical plant industries due to its excellent corrosion resistance and high strength, was evaluated in this study. Friction welding was introduced and conducted at a rotation speed of 2,000 RPM, friction pressure of 30 MPa, burn-off length of 5 mm and upset pressure of 110 ~ 200 MPa on rod typed specimens. The grain boundary characteristics distributions such a grain size, shape, misorientation angle and kernel average misorientation of the welds were clarified by electron backscattering diffraction method. The application of friction welding on SUS304 alloy resulted in a significant refinement of the grain size in the weld zone (5.11 mm) compared to that of the base material (48.09 mm). The mechanical properties of the welds, on the other hand, appeared to be relatively low or similar to those of the base material, which were mainly caused by dislocation density in the initial material and grain refinement in the welds.

• Archives of Plastic Surgery
• /
• 제32권1호
• /
• pp.67-70
• /
• 2005

Recently, the usage of an exercising treadmill has increased in Korean homes. Along with increasing utilization of these machines, injuries relating to the inadvertent usage of the machine have gradually increased for the last several years. The purpose of this study is to identify the feature of this type of injury, thereby to help prevent and to raise an awareness of the potential injury. 25 patients who had been admitted to Hangang Sacred Heart Hospital from January 2002 through March 2004 were investigated retrospectively. Age, sex, place of injury, the area and the extent of injury, treatment and prognosis were analyzed for each case. All injuries involved in the children with an average age of 3.5 years. This new type of injury was at least a deep second-degree burn of the friction-burn type in all cases. Most of them primarily involved hands. Inattention of the guardian was the main cause of such injuries. 68% of the cases needed an operation such as a split-thickness skin graft or a full-thickness skin graft. In this study, authors reached a conclusion that such injuries may be prevented by an education of the potential risks of using a treadmill and by developing additional safety devices.

• Journal of Welding and Joining
• /
• 제3권2호
• /
• pp.1-9
• /
• 1985

In this study, the influence of carbon equivalents on friction welds of similar steels was investigated. Four types of steels with 15mm diameter tested in the wide range of carbon equivalents from 0.3 to 1.1 Main experimental results are summarized as follows : (1) Under the constant burn-off length, the friction time becomes longer with the increasing carbon equivalent, but the upset length shows no consistent tendencies. (2) Due to the recrystallization in the contact area, the maximum hardness occurs some away from the contact surface. And it increases almost linearly with the increasing carbon equivalent. (3) Even a steel with 1.1 C.E. can be friction welded to make defect-free welds. (4) With the increasing carbon equivalent, the bend angle and charpy impact value decrease very rapidly in the range from 0.3 C. E., but remain nearly unchanged for C. E. higher than 0.6. (5) Heat treatment of the base metals before welding has very little influence on the mechanical properties of welds. On the other hand, normalizing of the welds improves the bend angle and charpy impact value, but its effect becomes almost negligible, when the carbon equivalents are higher than 0.6.

• 자원환경지질
• /
• 제5권4호
• /
• pp.187-209
• /
• 1972

발파(發破)에 있어서 천공배치(穿孔配置)는 발파효과에 영향(影響)을 미치는 가장 중요(重要)한 요소중(要素中)의 하나다. Burn-cut 의 폭발(爆發)의 여러 요소(要素)에 관(關)한 연구(硏究)는 Brown, Cook에 의(依)해 발표(發表)된 바 있으나 본연구(本硏究)에 있어서는 Burn-cut 와 Pyramid-cut의 천공배치(穿孔配置)의 대비(對比)와 폭원(爆源)과 자유면(自由面)사이의 역학적(力學的) 응력해석(應力解析)에 중점(重點)을 두어 이등교수(伊藤敎授)가 전개(展開)한 이론(理論)에서 다루지 않은 주정천공배치(週正穿孔配置)에 의(依)한 Burn-cut의 효과을 연결(連結)시켰다. 종래(從來)의 이론(理論)에 의(衣)하면 단일자유면발파(單一自由面發破)에 있어서는 압축응력외(壓縮應力外)에 자유면(自由面)에서 반사(反射)되는 인장응력(引張應力)의 영향(影響)을 추가(追加)로 받는다. 본(本) 신천공(新穿孔) 배치(配置)에 의(依)한 Burn-cut는 자유면수(自由面數)의 증가(增加)와 거리(距離)의 축소(縮少)를 꾀하므로서 이효과(效果)는 더욱 증대(增大)된다. 이와 같은 효과를 위(爲)해서는 다음 두가지 점(點)을 고려해야 한다. 첫째 심기공(心技孔)의 무장약공(無裝藥孔)은 보조응력(補助應力)을 크게 하기위(爲)해 가능(可能)한 대구경(大口徑)으로 깊게 천공(穿孔)해야 한다. 둘째 각 심기공간(心技孔間)의 거리(距離)를 접근(接近)시켜 완전(完全) 발파(發破)를 기(期)해야 한다. 그 까닭은 구경(口徑)이 증가(增加)됨에 따라 2차(次) 자유면(自由面)은 넓어지고 거리가 가까울수록 장약공(裝藥孔)과 무장약공(無裝藥孔)사이의 인장응력(引張應力)은 더욱 발달(發達)되기 때문이다. 선진국(先進國)에서는 심기공(心技孔)사이의 거리(距離)를 4"로 함이 이상적(理想的)이라고 알려지고 있으나 본실험(本實驗)에 의(依)하면 더 욱 근접(近接)될수록 파괴암석(破壞岩石)이 증가(增加)되고 굴진장(掘進長)도 깊어짐이 밝혀졌다. 나아가서는 굴진장(掘進長)을 더욱 증대(增大)시키기 위(爲)해 Burn-cut로 부터 Large hole Burn-cut를 개발(開發)하여 발파회수(發破回數) max 7회(回)/일(日)로서 1발파당(發破當) 3.1m까지 시도(試圖)함으로서 고속도굴진(高速度掘進)의 기원(起源)을 마련했다. 또한 대구경(大口徑) Burn-cut에서는 큰 저항(抵抗)을 극복하기 위해 금속초유폭약(金屬硝油爆藥)을 사용(使用)함이 더욱 효과적(效果的)임이 입증(立證)됐다. 최근(最近)에 와서 저렴(低廉)한 가격(價格)과 취급안전(取扱安全)으르 각광을 받고있는 AN-FO는 비료용 또는 공업용(工業用) 초안(硝安)에 연료유(燃料油)를 혼합(混合)한 것으로서 외관(雷管)만으로는 순감(純感)하여 폭발(爆發)하지 않으나 Gelatin Dynamite등(等)의 폭발성(爆發性) 예감제(銳感劑)에 의(依)해 발파공내(發破孔內)에서 일단 기폭(起爆)되면 종래(從來)의 초안폭약(硝安爆藥)에 상당(相當)한 위력(威力)을 발휘(發揮)케 한다. AN-FO 폭제(爆劑)의 성능(性能)에 관(關)해서는 많은 보고(報告)가 있었으나 본(本) 실험(實驗)에 의(依)하면 초유혼합비(硝油混合比)는 분상(粉狀)은 93.5:6.5, prill상(狀)은 94:6이 최적(最適)이며 분상(粉狀) AN-FO는 prill상(狀) AN-FO보다 항상(恒常) 폭속(爆速)이 높다. 또한 기폭감도(起爆感度), 충격감도(衝擊感度), 진거감도(塵據感度) 등(等) 제감도(諸感度)는 타화약(他火藥)에 비(比)해 몹시 경감(鏡感)하며 전폭성(傳爆性)은 prill상(狀)이 분상(粉狀)보다 우수(優秀)함을 얻었다. 발파후(發破後) Gas도 양호(良好)하며 AN-FO는 제조후(製造後) 7일(日) 전후(前後)가 최대효과를 갖는다. 종래(從來) AN-FO는 지난 여러해 동안 로천굴(露天掘)에만 사용(使用)하여 왔으나 필자(筆者)는 AN-FO의 기초성능시험(基礎性能試驗)을 토대(土臺)로 이를 이용(利用)한 신종폭제(新種爆劑)로서 금속초유폭약(金屬硝油爆藥)과 수중폭약(水中爆藥)을 발전(發展)시켰다. 금속초유(金屬硝油)의 폭약(爆藥)은 AN-FO와 Al 금속분말의 혼합물(混合物)이며 수중폭약(水中爆藥)은 종래폭약(從來爆藥)과 AN-FO로 제조(製造)한 바 이에 관(關)해서는 다른 논문(論文)에 기술(記述)했다. 본(本) 연구(硏究)에 있어서는 단일자유면(單一自由面) 발파(發破)에 있어서 격유폭약류(隔油爆藥類)를 사용(使用)한바 그 효과(效果)가 매우 양호(良好)하였음을 확인(確認)하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제36권2호
• /
• pp.276-285
• /
• 2012

본 연구목적은 열간압연용 런-아웃 테이블 롤러 표면의 기계적 성질을 개선하기 위해 다공질 자용성 합금으로 피복하는 방법을 개발하는 것이다. 열간압연에서 런-아웃 테이블의 롤러 내구성을 높이기 위해서는 고온에서 롤러표면의 경도를 높게 유지해야 하고, 내마모성, 내식성, 내열성, 내소부성 및 내응착성의 향상을 유지하여야 한다. 또한, 고온의 열연 강판을 안정적으로 이송할 수 있도록 하기 위해서는 롤러표면에 적절한 마찰계수를 유지하도록 하여야 하고, 롤러와 강판 사이에 미끄럼 발생이 없어야 한다. 본 연구에서는 자용성 합금에 텅스텐카바이드를 첨가시켜 서메트화하여 롤러의 내마모성을 증대시켰고, 미세 철분말을 롤러표면에 피복하여 다공질을 만들어 마찰계수를 높이고 붙잡음성을 향상시켰다. 그 결과, Ni-Cr 피복 롤러에 비하여 다공질 자용성 합금 피복 롤러는 피복층에 철분이 5 ~ 10 wt%로 많이 함유되어 재용융 공정에서 전기로로 가열하여 일부분만 합금화되고 나머지는 산화 및 용해에 의해 탈락되어 다공질로 나타나 강판과의 붙잡음성을 향상시켰다.