• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.93-93
• /
• 2010

We developed friction welded bimetallic sleeve for 220kV aluminum conductor XLPE cable. Not only friction welded bimetallic sleeve for Termination(EB-A, EB-G) but also friction welded sleeve for Joint of Al to Cu conductor was developed regardless of this project. Generally, friction welded sleeve used to connect Al conductor cable to Cu conductor cable and used for improvement of mechanical property of terminal by offer the copper side of friction welded bimetallic sleeve at the Termination. Connection method for Al-Cu conductor has mainly used friction welding at the solid state, because it is difficult to connect by using conventional welding method. this investigation introduces development of friction welded bimetallic sleeve by friction welding and test result of 220kV Al conductor XLPE cable and accessories using friction welded sleeve.

• Tribology and Lubricants
• /
• 제15권2호
• /
• pp.178-183
• /
• 1999

This paper presents friction and wear related results of thermite and gas pressure welded rails under various environmental contact conditions. A welded rail which was fabricated by thermite welding and gas pressure one has been tested over full range of test conditions in a pin-on-disk wear testing machine. The results show that the friction coefficient and wear rates of a welded rail are heavily dependent on the contact pressures and sliding environments for two welding methods such as thermite and gas pressure weldings.

• 한국자동차공학회논문집
• /
• 제13권2호
• /
• pp.142-148
• /
• 2005

In this paper, the stress singularity on interface of friction welded dissimilar materials was investigated by using 2-dimensional elastic boundary element method. It is required that stress distributions and stress singularities on an interface for friction welded dissimilar materials analize to establish strength evaluation. The stress singularity index ($\lambda$) and stress singularity factor ($\Gamma$) were calculated from the results of stress analysis. The stress singularities on variations for shapes and thickness of friction welded flashes were analized and discussed. This paper suggested that the strength evalution by using the stress singularity factors as fracture parameters, considering the stress singularity on an interface edge of friction welded dissimilar materials were very useful.

• 한국자동차공학회논문집
• /
• 제14권4호
• /
• pp.59-67
• /
• 2006

Recently, application of friction welded SUH35/SUH3 is increasing in the manufacturing process of automotive engine valves For securing its reliability and a reasonable strength evaluation method, it is necessary to assess stress singularity under the residual stress condition on the friction welded interface between dissimilar materials. In this paper, strength evaluation method of friction welded materials was investigated by boundary element method and static tensile testing. An advanced method of quantitative strength evaluation for SUH35/SUH3 friction welded material is to be suggested by establishing fracture criterion by using stress singularity factors.

• 한국자동차공학회논문집
• /
• 제15권4호
• /
• pp.171-177
• /
• 2007

In this paper, an evaluation method of fracture toughness on interface cracks was investigated in friction welded dissimilar materials with interfacial edge cracks. To establish a reasonable strength evaluation method and fracture criterion, it is necessary to analyze stress intensity factor under the load and residual stress condition on friction welded interface between dissimilar materials. The friction welded specimens with an edged crack were prepared for analysis of stress intensity by using the boundary element method (BEM) and the fracture toughness. A quantitative fracture criterion for friction welded STS 304/SM 45C with interface crack is suggested by using stress intensity factor, F and the results of fracture toughness experiment.

• 한국해양공학회지
• /
• 제4권2호
• /
• pp.94-99
• /
• 1990

This paper deals with investigating experimentally the effects of PWHT on the weld quality such as strength, toughness, hardness and micro-structure of the welded joints in friction welding of torsion bar material SUP9A bar to bar. The results obtained are summarized as follows; 1) It was certified that the condition of the post-weld heat treatment(PWHT) for the friction welded joints was very satisfactory because both strength and toughness of the joints were improved as almost same as those of the base metal or better by the PWHT. 2) The peak of hardness distribution of the friction welded joints can be eliminated by PWHT, resulting in being almost equalized at the weld interface, the HAZ(heat affected zone) and the base metal. 3) The micro-structure of the base meta., HAZ and weld interface(WI) of friction welded joints welded at the optimum welding condition consists of the same sorbite structure obtained by PWHT and fined sorbite at WI, resulting in increasing toughness as well as strength, and no micro structural defect has been found at the friction welded zone.

• 한국해양공학회지
• /
• 제4권2호
• /
• pp.244-244
• /
• 1990

This paper deals with investigating experimentally the effects of PWHT on the weld quality such as strength, toughness, hardness and micro-structure of the welded joints in friction welding of torsion bar material SUP9A bar to bar. The results obtained are summarized as follows; 1) It was certified that the condition of the post-weld heat treatment(PWHT) for the friction welded joints was very satisfactory because both strength and toughness of the joints were improved as almost same as those of the base metal or better by the PWHT. 2) The peak of hardness distribution of the friction welded joints can be eliminated by PWHT, resulting in being almost equalized at the weld interface, the HAZ(heat affected zone) and the base metal. 3) The micro-structure of the base meta., HAZ and weld interface(WI) of friction welded joints welded at the optimum welding condition consists of the same sorbite structure obtained by PWHT and fined sorbite at WI, resulting in increasing toughness as well as strength, and no micro structural defect has been found at the friction welded zone.

• 동력기계공학회지
• /
• 제6권4호
• /
• pp.49-55
• /
• 2002

In this paper, the elevated temperature tensile properties and short-time creep rupture characteristics were investigated for the friction welded joints of dissimilar materials, Cu-1%Cr-0.5%Zr and STS316L. The joining tests on Cu-1%Cr-0.5%Zr/STS316L by friction welding were performed, and optimum joining conditions of the friction welded joints were determined. The characteristics of the elevated temperature tensile strength, hardness, fractographs were examined, and the creep rupture characteristics for the optimum welded joints were investigated under uniaxal static load at 300, 400 and $500^{\circ}C$.

• 한국자동차공학회논문집
• /
• 제14권5호
• /
• pp.164-171
• /
• 2006

Application of friction welding is increasing in the manufacturing process of machine elements in many industry fields. To establish a reasonable strength evaluation method and fracture criterion, it is necessary to analyze stress singularity under the residual stress condition on friction welded interface between dissimilar materials. In this paper, a method to establish fracture criterion on interface of friction welded dissimiliar materials was investigated by using the boundary element method BEM and static tensile testing. A quantitative fracture criterion for friction welded dissimilar materials is suggested by using stress singularity factor, $\Gamma$.

• 한국자동차공학회논문집
• /
• 제13권5호
• /
• pp.104-111
• /
• 2005

With increasing use of SUH35/SUH3 dissimilar materials for automotive engine valves, it is required that stress singularities under residual stress on an interface for friction welded dissimilar materials analyzed to establish strength evaluation. The stress singularity $index{\lambda}$ and stress singularities $factor{\Gamma}$ were calculated from using the results of stress analysis to consider residual stress and loads. The stress singularities on variations for shapes and thickness of welded flashes were analyzed and discussed. This paper suggested that the strength evaluation by using the stress singularity factors as fracture parameters, considering the stress singularity on an interface edge of friction welded dissimilar materials will be useful.