• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.1
• /
• pp.78-84
• /
• 2012

Mold may experience deterioration of molding quality as the abrasion of mold occurring due to friction between mold and molded product works as allowance in the course of press process. Therefore, to improve the wear-resistance of mold, methods like nitriding, carburizing, flame and induction surface hardening treatment etc have been applied. However, as such methods are accompanied by problems like shape limitation or product deformation etc, laser surface treatment technology is under review as surface treatment method that can solve such problems. Therefore, in this study, mold material cast iron was surface-treated by using high power diode laser. In previous report 1 and report 2, the heat treatment characteristics were compared by the differences of die materials and shapes, then this paper observed microstructure by using optical microscope and scanning electronic microscope to analyze the structural difference of hardened zone, interface area and base metal after heat treatment. And the structural condition was grasped through EDS. As a result of microstructure, hardened zone showed formation of acicular martensite.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.5
• /
• pp.555-559
• /
• 2011

Oil hydraulic piston pumps are extensively used worldwide because of their simple design, light weight, and cost effectiveness. However, an oil hydraulic pump is likely to have high leakage, friction, and low energy efficiency after long-term use. In oil hydraulic piston pumps the clearance between the valve block and the piston plays an important role in the volumetric and overall efficiency. We studied the wear property of the SACM645 material used in hydraulic piston pumps via experiments with different heat treatments. We prepared three different specimens. The maximum tensile strengths of the QT and QT-nitration specimens are similar (about 820 MPa), but the strains are significantly different. However, the fatigue characteristic depended on the heat treatment.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.863-868
• /
• 2009

The drag reduction(DR) for Betaine+Amin and Xantan Gum as kinds of surfactant and Polyacrylamide as kinds of polymer solution according to the fluid velocity, temperature and surfactant concentration were compared experimentally. For this study, two kinds of experimental apparatus for short time and long time measurement were established. Each experimental appratus was equipped with hot water storage tanks, pumps, testing pipe network, flowmeter, two pressure gauges and data logging system was built for them. Results showed that Betaine+Amin and Xanthan Gum as kinds of surfactant had appeared optimal DR around 200-500 ppm and their DR tended to be decreased when flow velocity increased but Polyacrylamide as kinds of polymer solution showed the opposite trend to be increased when flow velocity increased. The both of them showed above 40% DR in the case of better condition by the short term measurement. But Polyacrylamide as kinds of polymer solution showed more degradation than Betaine+Amin and Xanthan Gum as kinds of surfactant by the long term measurement. As a result, Betaine+Amin and Xanthan Gum as kinds of surfactant showed better materials to use to the district heating system.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.40 no.3
• /
• pp.456-464
• /
• 2016

A new combat uniform is improved for added combat safety with various functions such as survivability, battle conformity and a camouflage performance system. Camouflage performance is an important factor in terms of combat survivability since it makes identification difficult and provide security. The combat uniform is worn under extreme conditions (exposure to ultraviolet light, sweat and friction) and an excellent color fastness to repeated washing is required. In this study, we investigated the color management, durability and discoloration of new combat uniform fabric with a digital pattern for camouflage performance to provide preliminary color management data. We examined color differences between standard fabric and mass-produced combat uniform fabrics, color differences between each military supply contract firm and color changes in combat uniforms after 60 washing cycles. The slight color differences between standard fabric and mass-produced combat uniform fabrics were tolerable under quality criteria of Republic of Korea Ministry of National Defense. However, the differences between the military supply contract firms were recognizable to the naked eye and increased with repeated washing. Continuous research on color fastness under repeated washing and color management is required to standardize reliability from each military supply contract firm for the daytime performance of a combat uniform's camouflage.

• Applied Chemistry for Engineering
• /
• v.31 no.3
• /
• pp.284-290
• /
• 2020

Energetic thermoplastic elastomers (ETPEs) based on glycidyl azide polymer (GAP) and carboxylated GA copolymers [GAP-ETPE and poly(GA-carboxylate)-ETPEs] were synthesized using isophorone diisocyanate (IPDI), dibutyltin dilaurate (DBTDL), 1,4-butanediol (1,4-BD), and soft segment oligomers such as GAP and poly(GA-carboxylate). The synthesized GAP-ETPE and poly(GA-carboxylate)-ETPEs were characterized by Fourier transform infrared (FT-IR), gel permeation chromatography (GPC), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), universal testing machine (UTM), calorimetry and sensitivity towards friction and impact. DSC and TGA results showed that the introduction of carboxylate group in GAP helped to have better thermal properties. Glass transition temperatures of poly(GA-carboxylate)-ETPEs decreased from -31 ℃ to -33 ℃ compared to that of GAP-ETPE (-29 ℃). The first thermal decomposition temperature in poly(GA_0.8-octanoate_0.2)-ETPE (242 ℃) increased in comparison to that of GAP-ETPE (227 ℃). Furthermore, from calorimetry data, poly(GA-carboxylate)-ETPEs exhibited negative formation enthalpies (-6.94 and -7.21 kJ/g) and higher heats of combustion (46713 and 46587 kJ/mol) compared to that of GAP-ETPE (42,262 kJ/mol). Overall, poly(GA-carboxylate)-ETPEs could be good candidates for a polymeric binder in solid propellant due to better energetic, mechanical and thermal properties in comparison to those of GAP-ETPE. Such properties are beneficial to application and processing of ETPE.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.5 no.3
• /
• pp.23-30
• /
• 2002

In recently, using of steel reinforcements by reinforcing materials of the reinforced earth, micro-pile and root-pile etc,. is wide-spreading in the stabilizing control of cutting and embankment slopes, but the failure mechanism of reinforced earth as well as the effect of insert angles or types of reinforcement and others are not defined clearly. In this study, therefore heavy-duty direct shear tests were exercised on the reinforced soil and the non-reinforced soil, which was executed for research on the interaction of soil-reinforcement and theirs behavior. The hardness and softness and the standard sands were used for modeling of reinforced soil, the material constants for the computer simulation were estimated from the results of CD-Test. The effects of reinforcing and of friction increasing on the softness, area ratio of reinforcements is equal, were the better than them of the hardness, as well the reinforcing effects of shear strength without regard to the area ratio is much the same at $10^{\circ}$, insert angle of reinforced bar, differ from them of the existing study. Then, the results of numerical analysis showed that the behavior of reinforcements displayed bending resistance and shear resistance at $15^{\circ}$ and $30^{\circ}$, respectively. Also, the state of strain transfer was observed and the behavior of resistance mechanism on reinforcements presented almost the same them of landslides stabilizing pile.

• Clinics in Shoulder and Elbow
• /
• v.11 no.1
• /
• pp.19-23
• /
• 2008

Purpose: To evaluate the bursoscopic findings of refractory primary adhesive capsulitis of the shoulder and to determine the clinical correlation. Materials and Methods: Arthroscopic capsular release was performed in 21 refractory adhesive capsulitis patients who had not responded to conservative treatment. The VAS for pain, range of motion, UCLA score was checked before and after surgery, and at the last follow up. Results: Bursitis, mild friction and impingement on coracoacromial ligament, as well as adhesion were observed. The function and pain improved earlier than after simple acromiohumeral joint capsular release. Conclusion: Subacromial bursoscopy helps rule out a hidden secondary frozen shoulder or secondary changes with primary adhesion. In addition, it has the advantage of being both a treatment and procedure for making a prognosis.

• Journal of Chest Surgery
• /
• v.25 no.6
• /
• pp.598-604
• /
• 1992

Rhabdomyosarcoma is the most common soft tissue sarcoma in childhood and acounts for 6% to 15% of all cases of childhood cancer, Rhabdomyosarcoma in seventh most common form of childhood neoplasms, following acute leukemia, tumors of the central nervous system, lymphoma neuroblastoma, Wilm`s tumor, bone tumor. Rhabdomyosarcoma can arise anywhere in the body, but primary site in the thorax is relatively rare. We experienced a case of aveolar rhabdomyosarcoma arising from intercostal muscle, A 12 year-old woman was suffered from the intermittent left chest pain radiating to the scapular area and dyspnea, On physical examination, pulmonary friction rub was heard on the left upper lobe area. Qn adimission, the chest simple radiography revealed a 7 x 6, 5cm sized radio-opaque mass with pleural effusion in the superior mediastinum and the CT showed a well difined radio-opaque mass including the destructed 2nd rib and pleural effusion. The percutaneous tra-nsthoracic needle aspiration biopsy was likely to show blastoma. After the chemotherapy[vincristine, actinomycin-D, cyclophosphamde] was done to treat blastoma, the pleural effussion was subsided and the mass was slightly decreased by 4.5x 4. 5cm. For treatment and diagnosis, we performed en-bloc resection and the defected chest was reconstucted with Gortex patch. Grossly, the specimen was colored graysh-white and arised in between two ribs The microscopic findings showed that the tumor cells were small round with scant pinkish cytoplasm on the H-E stain and the tumor cell nests were grouped by reticulum fibers and showed alveolar pattern on the silver stain The electromicroscopic finding presented that the cytoplasm contained tangled fibrillar and flocculent materials. The histopathologic findings were compatable with laveolar rhabdomyosarcoma. She was discharged without any complication. After discharge, she has been treated with radiation theraphy and chemotheraphy, and not recurred untill last follow-up We report a case of alveolar rhabdomyosarcoma arising to intercostal muscle, developed in 12 year-old waman, with brief review of literatures.

• The Research Journal of the Costume Culture
• /
• v.22 no.3
• /
• pp.431-439
• /
• 2014

This research verified the usefulness and practicality of citrus peel extract as a natural dye. This study dyed cotton, silk, and cotton/mulberry fiber blended fabrics using citrus peel extract, and measured the dyeability and functional property to verify their usefulness and practicality. The dyeing affinity of the citrus peel extract was measured by dyeing under alkaline conditions to determine the temperature and time for optimal dyeing conditions of the solution. The results show that a temperature and time of $60^{\circ}C$ and 30 minutes were optimal for dyeing cotton fabrics with citrus peel extract, $50^{\circ}C$ and 60 minutes for silk fabrics, and $60^{\circ}C$ and 60 minutes for cotton/mulberry fiber blended fabrics, respectively. In addition the results of measuring the color fastness of the cotton, silk, and cotton/mulberry fiber blended fabrics dyed with the citrus peel extract show that the color fastness was superior for washing, friction, sweat, and water. However, the color fastness for sunlight appeared to be slightly weak. In addition, it was found that fabric dyed with the citrus peel extract showed partial antimicrobial properties. The antimicrobial property appeared the greatest in the silk fabric. The cotton/mulberry fiber blended fabrics had 90% or more Staphylococcus aureus present, but the antimicrobial properties were not high in the cotton fabric. Additionally, the heavy metal content, which is harmful to the human body, appeared to be lower than standard figures, so the dye was found to be innocuous to humans. Therefore, when the results of this study are put together, citrus peel extract is sufficiently useful and practical as an ingredient for a natural dye. Moreover, there is ample possibility to develop citrus peel dyed fabrics as environmentally friendly fashion materials.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.110-110
• /
• 2011

The nanomechanical properties of fully lithiated and unlithiated silicon nanowire deposited on silicon substrate have been studied with atomic force microscopy. Silicon nanowires were synthesized using the vapor-liquid-solid process on stainless steel substrates using Au catalyst. Fully lithiated silicon nanowires were obtained by using the electrochemical method, followed by drop-casting on the silicon substrate. The roughness, derived from a line profile of the surface measured in contact mode atomic force microscopy, has a smaller value for lithiated silicon nanowire and a higher value for unlithiated silicon nanowire. Force spectroscopy was utilitzed to study the influence of lithiation on the tip-surface adhesion force. Lithiated silicon nanowire revealed a smaller value than that of the Si nanowire substrate by a factor of two, while the adhesion force of the silicon nanowire is similar to that of the silicon substrate. The Young's modulus obtained from the force-distance curve, also shows that the unlithiated silicon nanowire has a relatively higher value than lithiated silicon nanowire due to the elastically soft amorphous structures. The frictional forces acting on the tip sliding on the surface of lithiated and unlithiated silicon nanowire were obtained within the range of 0.5-4.0 Hz and 0.01-200 nN for velocity and load dependency, respectively. We explain the trend of adhesion and modulus in light of the materials properties of silicon and lithiated silicon. The results suggest a useful method for chemical identification of the lithiated region during the charging and discharging process.