• Korean Journal of Environmental Agriculture
• /
• v.16 no.1
• /
• pp.72-79
• /
• 1997

Adsorption, leaching, and retention of the Flupyrazofos(KH-502), a new active ingredient for insecticide, in the soils under laborarory and field conditions were investigated to provide the basic data for the safety use and to assess a secondary impact of this insecticide on soil and water environments. A significant power function relation was found between the adsorbed KH-502 and time, representing that 45% of the added KH-502 was adsorbed within 30 min. but a quasiequilibrium was reached after 6 to 12 hr with a slower adsorption. Adsorption phenomena followed th first-order kinetics and time required for 50% adsorption was 5.8 hr. The equilibrium adsorption isotherm was explained by the Freundlich equation and was classified as S-type. The amounts of KH-502 leached through the soil column (C) as compared to initial conc. ($C_0$) were very low and these relative concentrations ($C/C_0$) were 0.073 and 0.017 in SL and CL soils, respectively. The residual conc. of KH-502 in the surface soil was comparatively low and decreased with time. Half-lives of KH-502 in the surface soil was comparatively low and decreased with time. Half-lives of KH-502 under the field conditions were estimated to be 20 and 18 days in the SL and CL soils, respectively. The KH-502 cone, transported to the subsurface soils was extremely low. These results demonstrate that KH-502 has a low pollution risk potential to the surrounding environment as far as it is used following the recommended guideline.

• Journal of the Korean Chemical Society
• /
• v.65 no.3
• /
• pp.197-202
• /
• 2021

In this study, activated clay treated with H₂SO₄ (20% by weight) and heat at 90 ℃ for 8 h for acid white soil was used as an adsorbent for the removal of PO₄^3--P in water. Prior to the adsorption experiment, the characteristics of activated clay was examined by X-ray Fluorescence Spectrometry (XRF) and BET surface area analyser. The adsorption of PO₄^3--P on activated clay was steeply increased within 0.25 h and reached equilibrium at 4 h. At 5 mg/L of low PO₄^3--P concentration, roughly 98% of adsorption efficiency was accomplished by activated clay. The adsorption data of PO₄^3--P were introduced to the adsorption isotherm and kinetic models. It was seen that both Freundlich and Langmuir isotherms were applied well to describe the adsorption behavior of PO₄^3--P on activated clay. For adsorption PO₄^3--P on activated clay, the Freundlich and Langmuir isotherm coefficients, K_F and Q, were found to be 8.3 and 20.0 mg/g, respectively. The pseudo-second-order kinetics model was more suitable for adsorption of PO₄^3--P in water/activated clay system owing to the higher correlation coefficient R² and the more proximity value of the experimental value q_e,exp and the calculated value q_e,cal than the pseudo-first-order kinetics model. The results of study indicate that activated clay could be used as an efficient adsorbent for the removal of PO₄³-P from water.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.1
• /
• pp.136-142
• /
• 2007

Recent publications have paid attention on the utilization of solid reagents for the removal of substances causing eutrophication, in particular $PO_4^{3-}$ ions. The adsorption of dissolved inorganic phosphate on slag produced by the refining process of iron ore was fundamentally studied for suppressing the liberation of phosphate from wastewater. This study has been conducted in order to find a possibility to improve the phosphate removal and to evaluate the phosphate removal variation to form hydroxyapatite, when the converter slag is used for phosphate removal. The result shows that the converter slag can be applied to remove phosphate using Freundlich isotherm. The size of converter slag, $2{\sim}0.425 mm$ was more efficient than $2{\sim}4.75mm$ to remove phosphate. In particular, 1 mg/L of phosphate can be removed up to 80% of the initial concentration for the continuous column experiment.

• Applied Chemistry for Engineering
• /
• v.33 no.2
• /
• pp.151-158
• /
• 2022

In this paper, parameter characteristics such as pH effect, isotherm, kinetic and thermodynamic parameters and competitive adsorption of dyes including malachite green (MG), direct red 81 (DR 81) and thioflavin S (TS), which have different functional groups, being adsorbed onto activated carbon were investigated. Langmuir, Freundlich and Temkin isotherm models were employed to find the adsorption mechanism. Effectiveness of adsorption treatment of three dyes by activated carbon were confirmed by the Langmuir dimensionless separation factor. The mechanism was found to be a physical adsorption which can be verified through the adsorption heat calculated by Temkin equation. The adsorption kinetics followed the pseudo second order and the rate limiting step was intra-particle diffusion. The positive enthalpy and entropy changes showed an endothermic reaction and increased disorder via adsorption at the S-L interface, respectively. For each dye molecule, negative Gibbs free energy increased with the temperature, which means that the process is spontaneous. In the binary component system, it was found that the same functional groups of the dye could interfere with the mutual adsorption, and different functional groups did not significantly affect the adsorption. In the ternary component system, the adsorption for MG lowered a bit, likely to be disturbed by the other dyes meanwhile DR 81 and TS were to be positively affected by the presence of MG, thus resulting in much higher adsorption.

• Korean Journal of Environmental Agriculture
• /
• v.11 no.3
• /
• pp.195-200
• /
• 1992

Heavy metal adsorption on peat was studied to examine the utilization of abundant natural resouces as pollution control. The smaller the peat particle size, the more the heavy metals studied were adsorbed. Adsorption of heavy metals on peat was greater in single metal solutions than in mixed solutions, and the order of adsorption amount on peat was Cu > Cd > Zn. The most effective pH range of the adsorption of Cd, Zn, and Cu was between 4 and 6. With increasing the concentration of heavy metals the amount of adsorption on peat was increased, but the adsorption ratio was decreased. The adsorption of heavy metals on peat was fitted to the Freundlich isotherm and peat was appeared to be an effective adsorbent of the heavy metals. The treatment of polyethyleneimine(PEI) on the peat surface effectively increased adsorption capacity of the heavy metals. Because of its higher energy content, the heavy metal adsorbed peat could be utilized as a energy source. After burning the peat, the reduced peat volume could be save the expenses for waste disposal.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 1997.10a
• /
• pp.65-66
• /
• 1997

우리나라의 대부분 하천과 인공댐의 경우 조류발생에 기여하는 영양염은 질소, 인 그리고 규소 등인데 특히 인이 생산제한 인자로 작용하고 있다. 따라서 인을 적절히 제거할 경우에는 조류 발생에 의한 수질의 악화와 수이용의 저해요인을 배제할 수 있어 이에 대한 연구가 많이 진행되어 왔다. 지금까지와 연구는 인의 화학적 응집 침전법, 생물학적 처리법에 대하여 수행되어 왔으나 설비자금, 운영비, 운전기술, 슬러지 생성 그리고 제거효율 등에서 만족스런 결과가 도출되지 못하여 현장 적용을 하지 못하고 있는 실정이다. 이러한 현실을 감안하여 우리의 자연 환경에서 쉽게 자할 수 있는 황토를 모재로하여 Al3-과 Fe3-, Ca2-을 적절히 배합하여, 주로 인을 선택적으로 제거하 고자 개발된 황토의 흡착능력 그리고 흡착 메카니즘에 대한 기본적인 연구를 하고자 (1) 등온흡착실험을 통하여 흡착용량을 평가하고 (2) 흡착제거속도를 평 가하였고 (3)파과시간 및 흡착특성을 파악하기 위해 column 흡착실험을 하였다 또한 (4) 황토내의 Al3-, Fe3-과 Ca2- 등이 인의 화학적 흡착에 기여하는 정도를 파악하여 흡착메카니즘을 규명하고자 하였다. 먼저 흡착용량실험을 위하여 PO3-4-P 농도 3ppm의 용액 200mf에 황토 0.2g, 0.5g, 1.0g, 2.0g을 각각 투여한 후 충분한 흡착평형이 일어나게 24시간 동 안 130rpm으로 $25^{\circ}C$ 등온반웅조에서 저어주어 흡착평형에 도달하면 상등액을 GF/C Filter로 여과한 후, 여액에 대해 PO3-4-P의 농도를 Ascrobic he건법으로 측정한 결파, Freundlich 등온흡착식에 의하면 K값은 17.34와 16.28이었으며 1/n 값은 1.32와 1.42로 인흡착 성능이 뛰어난 것으로 평가되었다. 둘째, 흡착속도 실험은 PO3-4-P 농도 1.5ppm의 용액 2f에 259의 황토를 투여하고 충분한 혼합이 일어날 수 있도록 170rpm으로 교반하면서 시간별 용액 의 농도 변화를 측정한 결과, 0.45mg/g/m교의 속도로 15분만에 94.3%의 인 제거 효율을 보였다. 셋째, 직경 12mm의 glass column에 황토를 209 채우고 1.5ppm의 PO34P 용액을 2.Sne11in의 유량으로 통수 시킨 후, 시간에 따른 농도 변화를 측정한 결과, 원수 농도의 50%에 해당하는 파과점까지 약 70시간 만에 도달하였다. 넷째, Al3-, Fe3-과 Ca2- 등이 화학적 흡착에 기여하는 정도를 파악하기 위 하여 황토 2g에 대하여 Hieltijes and Lijklema 방법에 의해 Adsorbed-p, Nonapatite inorganic-P(NAI-P), Apatite-p, Organic-P로 구분하여 분석하고, 총인(Total Phosphorus)을 Standard Methods에 따라 Persulfate digestion후 0.45 m membrane 여지 여과하여 여액에 대해 PO3-4-P의 농도를 Ascorbic Acid 법으로 측정한 결과, NAI-P가 가장 큰 비율을 차지하였고, 부원료로 첨가된 금속 양이온 중 Fe3-이온이 흡착에 기여하는 정도가 가장 큰 것으로 평가되었다.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.4
• /
• pp.723-731
• /
• 2000

In recent years, the amount and number of synthetic organic compounds(SOCs) discharged from various industries has been increasing. Granular activated carbon(GAC) adsorption is one of the best available technology to remove SOCs from water supplies and wastewater. In this paper competitive adsorption for binary mixture of 4-nitrophenol and phenol on reverse stratified tapered adsorber(RSTA) using GAC was studied. Two isotherm experiments were conducted, one for phenol and the other for 4-nitrophenol. The phenol data of binary mixture isotherm were not fitted to Freundlich isotherm. The competitive adsorption increased significantly with decreasing carbon dose and increasing adsorbate concentration. The RSTA was found to provide an increase in breakthrough time when decreasing flow rate, increasing angle and injection layers. The performance enhancement provided by RSTA can be exploited in separation and in the purification of fluids.

• Resources Recycling
• /
• v.15 no.4 s.72
• /
• pp.13-18
• /
• 2006

This study was to investigate the extraction characteristics of extraction resins containing HEH/EHP for Gadolinium solution. The experiments were carried out with the variation of equilibrium pH and initial concentration of Gd. The optimum extraction time was 90 mins on Gd extraction using resin. The extraction ratio(%) was increased by increasing equilibrium pH from pH 1.0 to 2.0. The experimentally measured amounts of Gd on resins at equilibrium agreed well with those predicted using Freundlich's isotherm.

• Journal of the Korean Chemical Society
• /
• v.56 no.6
• /
• pp.692-699
• /
• 2012

The aim of the present study is to explore the possibility of utilizing loess and fly ash as well as activated carbon for the adsorptive removal of PCBs in transformer oil. Here, we investigated the effect of various factors such as temperature (5, 25, 55), contact time (30 min-3 day) and adsorbent does (1, 2.5, 5, 10 g) in detail. It was found that PCBs adsorption rate from transformer oil by activated carbon is more favored than loess at the equilibrium time of 60 minutes. The equilibrium data for both activated carbon and loess is fitted well to the Freundlich isotherm model. The rate constant and activation energy of PCBs adsorption in transformer oil on each adsorbent was analyzed by fitting a kinetic model at 5, 25 and $55^{\circ}C$. From the thermodynamic parameters, the PCBs adsorption process for transformer oil/activated carbon and loess system is spontaneous and endothermic in nature.

• Analytical Science and Technology
• /
• v.15 no.2
• /
• pp.163-171
• /
• 2002

The adsorption characteristics of Cd(II) and Pb(II) ions has been studied by using chitin as an adsorbent. The pure chitin was obtained from the extraction of red-crab shell dumped by fish factory. Adsorption kinetics of Cd(II) and Pb(II) ions on the chitin reached at the maximum adsorption within two minutes. Adsorbed amounts of heavy metals were pH 7.0>10.5>3.5 in the following order. Adsorption ratio by chitin was 21${\sim}$99% for Cd(II) ion and 24${\sim}$95% for Pb(II) ion. Recovery ratio of Cd(II) ion on the chitin was 22${\sim}$53%, and that of Pb(II) ion was 22${\sim}$73%. The adsorption behavior of these heavy metals was explained well by Freundlich adsorption isotherm.