• Journal of Navigation and Port Research
• /
• v.34 no.4
• /
• pp.271-279
• /
• 2010

The Mobile Harbor(MH) is a new transportation platform that can load and unload containers to and from very large container ships in the sea. This loading and unloading by crane can be performed with only very small movements of the MH in waves because MH is operated outside of the harbor. For this reason, an anti-rolling tank(ART) and an active mass driving system(AMD) were designed to reduce MH's roll motion, especially at the natural frequency of MH. In the conceptual design stage, it is difficult to confirm the design result of theses anti-rolling devices without modeling and simulation tools. Therefore, the coupled MH and anti-rolling devices' dynamic equations in waves were derived and a simulation program that can analyze the roll reduction performance in various conditions, such as sea state, wave direction, and so on, was developed. The coupled equations are constructed as an eight degrees of freedom (DOF) motion that consists of MH's six DOF dynamics and the ART's and AMD's control variables. In order to conveniently include the ART's and AMD's control dynamics in the time domain, MH's radiated wave force was described by an impulse response function derived by the damping coefficient obtained in the frequency domain, and wave exciting forces such as Froude-Krylov force and diffraction force and nonlinear buoyancy were calculated at every simulation time interval. Finally, the roll reduction performances of the designed anti-rolling devices were successfully assessed in the various loading and wave conditions by using a developed simulation program.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.11C
• /
• pp.1083-1090
• /
• 2005

This paper presents the design of a video encoder for the device of need TV-OUT function. The designed video encoder satisfies the standard conditions of International Telecommunication Union-Radiocommunication (ITU-R) BT.470. ITU-R BT.470 can be classified as NTSC, PAL or SECAM. NTSC and PAL use Amplitude Modulation (AM) to transmit color difference signals and SECAM uses Frequency Modulation (FM). SECAM must have an antic-cloche filter but the filter recommended by ITU-R BT.470 is not easy to design due to sharpness of the frequency response. So formerly the filter was designed as analog. This paper proposes that the filter is designed as digital and the special quality of the filter is transformed easy to design. And the modulation method is modified to be identical with the result required at standard. The encoder can control power consumption by output mode to apply mobile phone, mobile devices, etc. The proposed encoder is experimentally demonstrated with ALTERA FPGA APEX20KE EP20K1000EBC652-3 device and SAMSUNG LCD-TV.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.647-652
• /
• 2008

This paper focused on the application of finite element model updating technique to evaluate the structural properties of the reinforced concrete specimen using the data collected from shaking table tests. The specimen was subjected to six El Centro(NS, 1942) ground motion histories with different Peak Ground Acceleration(PGA) ranging from 0.06g to 0.50g. For model updating, flexural stiffness values of structural members(walls and slabs) were chosen as the updating parameters so that the converged results have direct physical interpretations. Initial values for finite element model were determined from the member dimensions and material properties. Frequency response functions(i.e. transfer functions), natural frequencies and mode shapes were obtained using the acceleration measurement at each floor and given ground acceleration history. The weighting factors were used to account for the relative confidence in different types of inputs for updating(i.e. transfer function and natural frequencies). The constraints based on upper/lower bound of parameters and sensitivity-based constraints were implemented to the updating procedure in this study using standard bounded variable least-squares(BVLS) method. The veracity of the updated finite element model was investigated by comparing the predicted and measured responses. The results indicated that the updated model replicates the dynamic behavior of the specimens reasonably well. At each stage of shaking, severity of damage that results from cracking of the reinforced concrete member was quantified from the updated parameters(i.e. flexural stiffness values).

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.7
• /
• pp.725-731
• /
• 2008

This paper focused on the application of finite element model updating technique to evaluate the structural properties of the reinforced concrete specimen using the data collected from shaking table tests. The specimen was subjected to six El Centre (NS, 1942) ground motion histories with different peak ground acceleration (PGA) ranging from 0.06 g to 0.50 g. For model updating, flexural stiffness values of structural members (walls and slabs) were chosen as the updating parameters so that the converged results have direct physical interpretations. Initial values for finite element model were determined from the member dimensions and material properties. Frequency response functions (i.e. transfer functions), natural frequencies and mode shapes were obtained using the acceleration measurement at each floor and given ground acceleration history. The weighting factors were used to account for the relative confidence in different types of Inputs for updating (j.e. transfer function and natural frequencies) The constraints based on upper/lower bound of parameters and sensitivity-based constraints were implemented to the updating procedure in this study using standard bounded variable least-squares(BVLS) method. The veracity of the updated finite element model was investigated by comparing the predicted and measured responses. The results indicated that the updated model replicates the dynamic behavior of the specimens reasonably well. At each stage of shaking, severity of damage that results from cracking of the reinforced concrete member was quantified from the updated parameters (i.e. flexural stiffness values).

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.441-447
• /
• 2002

KSR-III(Korea Sounding Rocket - III), which is being developed by Space Technology R&D Division of KARI(Korea Aerospace Research Institute) will be launched in late 2002. It is a three-stage, liquid propellant rocket which can reach 250 km altitude and will carry out observation of ozone layer and scientific experiments, such as microgravity experiment, and atmospheric measurement. KSR-III is believed to be an intermediate to the launch vehicle capable of carrying a satellite to its orbit. Space Test Department of KARI performed GVT(Ground Vibration Test) fer KSR-III EM at Rocket Test Building of KARI. GVT is very important for predicting the behavior of rocket in its operation, developing flight control program and performing aerodynamic analysis. This paper gives an introduction of rocket GVT configuration and information on test procedures, techniques and results of It. In this test. to simulate free-free condition, test object hung in the air laterally by 4 bungee cords specially devised. For the excitation of test object, pure random signal by two electromagnetic shakers was used and total 22 frequency response functions were achieved. Polyreference parameter estimation was performed to identify the modal parameters with MIMO(Multi-Input-Multi-Output) method. As the result of the test, low frequency mode shapes and modal parameters below 60Hz were identified

• Tribology and Lubricants
• /
• v.34 no.1
• /
• pp.33-41
• /
• 2018

This paper describes a new test rig for identification of rotordynamic force coefficients of squeeze film dampers (SFDs) in automotive turbochargers (TCs). Prior studies have mainly concentrated on relatively large-sized SFDs used in aircraft engines, turbocompressors, and turbopumps. The main objective of the current study is to propose a test rig for identification of dynamic force coefficients of small-sized SFDs (a journal diameter of ~11 mm). The current test rig consists of a journal, a SFD cartridge, four support rods, an upper structure, a data acquisition (DAQ) system, and an oil circulation unit. The annular gaps between the journal outer surface and SFD cartridge inner surface create SFD film lands. The damper has two parallel film lands separated by a central groove, having an axial length and depth of 3 mm. Each film land has a length of 4 mm with a $40{\mu}m$ radial clearance. The static load and dynamic impact tests identify the structural characteristics (i.e., stiffness and natural frequency) of the journal and assembled test rig. The measurements show good agreement with predictions. The SFD performance data from this test rig will be used to develop innovative TC rotor systems with improved NVH and reliability characteristics incorporating advanced SFD technology.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.3
• /
• pp.29-37
• /
• 2011

The modal characteristics of a compressor wheel of an automotive turbocharger have been investigated using an experimental method based on an acoustic frequency response function, p/f(${\omega}$), where p is sound pressure radiated from a structure, and f is impact force. First, a well-defined annular disc with narrow radial slots was examined to check whether the vibro-acoustic test could precisely determine natural quencies and vibration modes of structures showing that the vibro-acoustic test proposed in this paper was comparable to the conventional modal test with an accelerometer and the numerical analysis. The conventional method has been found to be inappropriate for compressor wheel because of additional mass due to the accelerometer and additional damping from the accelerometer cable alter the dynamic responses of the wheel blades. odal characteristics of the wheel have been defined using vibro-acoustic test and verified with the results from another conventional method using a laser vibrometer. Natural quencies and mode shapes of a turbocharger wheel, which can't be precisely obtained with onventional method, could be defined accurately without the additional effects from sensor and cable. Proposed method can be applied to small structures where conventional sensors and cables could generate troubles.

• Journal of the Institute of Convergence Signal Processing
• /
• v.7 no.4
• /
• pp.207-213
• /
• 2006

This paper presents the design and implementation of a video processor for the device of need TV-OUT function. The designed video processor satisfies the standard conditions of ITU-R(International Telecommunication Union-Radiocommunication) BT.470. Also, in order to apply various digital device, we concentrate upon hardware complexity. ITU-R BT.470 can be classified as NTSC, PAL or SECAM. NTSC and PAL use QAM(Quardarature Amplitude Modulation) to transmit color difference signals and SECAM uses FM(Frequency Modulation). FM must have antic-cloche filter but filter recommended by ITU-R BT.470 is not easy to design due to sharpness of the frequency response. So this paper proposes that the special quality of anti-cloche filter is transformed easy to design and the modulation method is modified to be identical with the result required at standard. The processor can control power consumption by output mode to apply portable digital devices. The proposed processor is experimentally demonstrated with ALTERA FPGA APEX20KE EP20K1000EBC652-3 device and SAMSUNG LCD-TV.

• Journal of the Society of Naval Architects of Korea
• /
• v.61 no.5
• /
• pp.297-311
• /
• 2024

In this study, a combined seakeeping performance evaluation method has been developed for the design purpose of the light aircraft carrier CVX of Korean Navy. A frequency domain analysis method was developed for evaluation of safe operating envelope up to sea state 6, while a time domain analysis method was developed for survival condition of sea state 7 and higher. The frequency-domain solver AdFLOW-Navy was developed by adding empirical formula of roll damping and fin-stabilizer to the existing AdFLOW by KRISO, which was based on the three-dimensional higher order boundary element method (HOBEM). For the estimation of the roll damping coefficient, a two-dimensional cross-section was automatically extracted from the three-dimensional panel, and the roll damping coefficient was analyzed for the two-dimensional cross-section. As for the time domain analysis method, KIMAPS-Navy was developed by improving and expanding the KIMAPS series developed by KRISO which is based on the impulse response function by utilizing the hydrodynamic coefficients obtained from the AdFLOW-Navy. In addition, a weakly nonlinear analysis approach was applied to analyze highly nonlinear motion under heavy sea states. Finally numeraical analysis results were compared with model tests, which showed practical usefulness of the present combined seakeeping analysis approach.

• Journal of Magnetics
• /
• v.21 no.3
• /
• pp.460-467
• /
• 2016

Magnetic hyperthermia mediated by superparamagnetic particles is mainly based in sinusoidal waveforms as excitation signals. Temperature changes are conventionally explained by rotation of the particles in the surrounding medium. This is a hypothesis quite questionable since habitual experimental setups only produce changes in the magnetic module, not in the field lines trajectories. Theoretical results were tested by changing the waveform of the exciting signal in order to compare non-sinusoidal signals against sinusoidal signals. Experiments were done at different frequencies: 200 KHz, 400 KHz, 600 KHz, 800 KHz and 1 MHz. Superparamagnetic Iron Oxide samples (SPION), made of magnetite ($Fe_3O_4$) and suspended in water (100 mg/ml), were used. Magnetic field strength varies from $0.1{\pm}0.015KA/m$ to $0.6{\pm}0.015KA/m$. In this study was observed that the power loss depends on the applied frequency: for 1 to 2.5 RMS current the responses for each signal are part of the higher section of the exponential function, and for 3.5 to 8 RMS current the response is clearly the decrement exponential function's tale (under $1{\times}10^3LER/gr$).