• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.709-714
• /
• 2017

Structures like bridges or buildings need to be checked continuously to diagnose their safety. However, it is extremely difficult for the people who access such structures to check all areas directly. To overcome this problem, there is a lot of active research into structural health monitoring (SHM) with wireless sensor nodes (WSNs). In this paper, for more accurate checking of SHM with WSNs, we experimentally compare and evaluate the performance of Xenomai, which provides real-time processing under the traditional Linux kernel. For this purpose, we patch Xenomai into the traditional Linux kernel of a commercial embedded board, Raspberry Pi, and implement a task that periodically reads vibration data of the z-axis from an accelerometer in order to analyze the natural frequency of cantilever beams. Reading the data from the traditional Linux kernel with the same method, we analyze the natural frequency of the cantilever beams using Smart Office Analyzer. Finally, to review the validity of Xenomai for WSNs, we obtain vibration data on the z-axis from the accelerometer via wired network and compared and analyzed them the same way.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.10
• /
• pp.929-934
• /
• 2016

In this paper, we studied the design and fabrication of array antenna at around 1.8 GHz band. To improve of frequency properties of antenna, single feed microstrip patch antenna was simulated by HFSS(High Frequency Structure Simulator). A $1{\times}2$ array antenna of 1.8 GHz for LTE band was designed and fabricated by photolithography on an FR4 substrate (dielectric constant of 4.4 and thickness of 0.8 mm). The fabricated antenna was analyzed by network analyzer. The measured results agree well with the simulations, which confirmed the validity of this study. The fabricated $1{\times}2$ array antenna showed a center frequency, the minimum return loss and impedance were 1.82GHz, -30.5dB, and $49.6{\Omega}$ respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.3
• /
• pp.454-459
• /
• 2007

In this work, micro-scale, high-performance solenoid-type RF chip inductors utilizing amorphous $Al_2O_3$ core material were investigated. The size of the chip inductors was $0.86{\times}0.46{\times}0.45mm^3$ and copper(Cu) wire with $27{\mu}m$ diameter was used as the coil. High frequency characteristics of the inductance(L), quality factor(Q), impedance(Z), and equivalent circuit parameters of the RE chip inductors were measured and analyzed using an RF impedance/material analyzer(HP4291B with HP16193A test fixture). It was observed that the RF chip inductors with the number of turns of 9 to 12 have the inductance of 21 to 34nH and exhibit the self-resonant frequency(SRF) of 5.7 to 3.7GHz. The SRF of inductors decreases with increasing the inductance and inductors have the quality factor of 38 to 49 in the frequency range of 900MHz to 1,7GHz.

• Journal of Korean Society on Water Environment
• /
• v.36 no.5
• /
• pp.392-404
• /
• 2020

The focus of this study was to quantify the thermal stratification and analyze the relationship between the stratification structure and the tributaries to understand flow variations in the Paldang Reservoir. The vertical distribution of the temperature and density gradients, and the depth and thickness of the thermocline were quantitatively calculated using a lake physics tool (rLakeAnalyzer) and high-frequency monitoring data. Based on a density gradient of 0.2 kg/㎥/m, the thermocline was formed from mid-May to early-September 2019 and the other periods were weakly stratified or mixed. The thickness of the thermocline was developed until 4.7 m and the depth of the thermocline was formed at a depth of 3 - 6 m at the front of the Paldang Reservoir. During the formation of the thermocline, the Namhangang and Gyeongancheon tributaries with relatively high water temperature (low-density) flowed into the upper layer of the reservoir, and the Bukhangang tributary with low water temperature (high-density) mainly affected the lower layer of the reservoir. This is because the density currents were formed due to the difference in the water temperature of the tributaries. The findings of this study may be used for constructing high-frequency monitoring and quantitative data analyses of reservoirs.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.30-30
• /
• 2011

The wave-cutoff tool is a new diagnostic method to measure electron density and electron temperature. Most of the plasma diagnostic tools have the disadvantage that their application to processing plasma where toxic and reactive gases are used gives rise to many problems such as contamination, perturbation, precision of measurement, and so on. We can minimize these problems by using the wave-cutoff method. Here, we will present the results obtained through the development of the wave-cutoff diagnostic method. The frequency spectrum characteristics of the wave-cutoff probe will be obtained experimentally and analyzed through the microwave field simulation by using the CST-MW studio simulator. The plasma parameters are measured with the wave-cutoff method in various discharge conditions and its results will be compared with the results of Langmuir probe. Another disadvantage is that other diagnostic methods spend a long time (~ a few seconds) to measure plasma parameters. In this presentation, a fast measurement method will be also introduced. The wave-cutoff probe system consists of two antennas and a network analyzer. The network analyzer provides the transmission spectrum and the reflection spectrum by frequency sweeping. The plasma parameters such as electron density and electron temperature are obtained through these spectra. The frequency sweeping time, the time resolution of the wave-cutoff method, is about 1 second. A short pulse with a broad band spectrum of a few GHz is used with an oscilloscope to acquire the spectra data in a short time. The data acquisition time can be reduced with this method. Here, the plasma parameter measurement methods, Langmuir probe, pulsed wave-cutoff method and frequency sweeping wave-cutoff method, are compared. The measurement results are well matched. The real time resolution is less than 1 ?sec. The pulsed wave-cutoff technique is found to be very useful in the transient plasmas such as pulsed plasma and tokamak edge plasma.

• Journal of the Korean Magnetics Society
• /
• v.6 no.6
• /
• pp.367-374
• /
• 1996

The developmement of electronic machine industries requires miniature of size as well as increasement of driving frequency in electronic parts, recently. To realize micro-struture of magnetic devices, in this study, we fabricated thin film inductors by using thin film manufacturing techniques such as photolithography and wet etching process, and these devices are measured at high frequency range of 1 MHz~1 GHz. The results are as follows. The accurate measuring technique by using network analyzer system having microstrip line was established. The manufactured inductors are fabricated with several ten micrometers by means of wet etching process known as easier and more economic than dry etching process. VVhen the device size of two types (spiral, meander) is the same, inductance value L and quality factor Q of spiral type devices are larger than those of meander type, but driving frequency of spiral type is lower than that of meander type due to increasement of inductance L. It is necessary to decrease resistance value R by increasing cross section of the conductor film coil. Thus high frequency measuring method would be a very useful for another measuring fields of the range over several hundreds MHz.

• Elastomers and Composites
• /
• v.52 no.4
• /
• pp.326-331
• /
• 2017

Two kinds of polyurethane elastomers were prepared and their acoustical properties underwater investigated. Their dynamic mechanical properties were measured using a dynamic mechanical analyzer. The sound speed and echo reduction in the 1-50 kHz frequency range were calculated from the data obtained using the analyzer. The sound speed, transmission and attenuation cofficient in 300-800 kHz were measured in a water-filled tank. Impedance tube experiments were performed to determine the reflective coefficient and echo reduction in the 3-8 kHz range. The polyurethane elastomer containing a hollow glass sphere showed a lower reflective coefficient and a higher echo reduction than the polyurethane elastomer without a filler.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1384-1387
• /
• 1996

SCPI(Standard Commands for Programmable Instrument) is a standard command sets designed for controlling various types of instruments. In order to control FFT(Fast Fourier Transform) analyzing device using SCPI it is required to support sweep measurement function. We defined SCPI command set for FFT analysis and developed parser of defined command set using lex(Lexical Analyzer Generator) and yacc(Yet Another Compiler Compiler). After developing FFT analyzing test was performed with that parser. Up to audible signal frequency the result of FFT analysis was accurate and that result was agree with that of conventional FFT analyzer. As a result it is proved that various types of instruments including sweep measurement instrument can be controlled with appropriate SCPI command sets. Also when developing new instruments the method used in this experiment will contribute to reducing the time required to develop the SCPI parser and increasing reliability.

• Journal of the Korean Magnetics Society
• /
• v.10 no.1
• /
• pp.22-29
• /
• 2000

The effective linewidth was measured using the conventional cavity perturbation method at 9.43 GHz in room temperature for Ca-Zr substituted yttrium iron garnet plate. The experimental set-up consists of the network analyzer, the electromagnet and the cylimdrical TE001 cavity. Measurement was performed in the static magnetic field perpendicular to the sample plane. The real and imaginary parts of diagonal component of the microwave susceptibility tensor are obtained from the resonance frequency and the quality factor Q of the cavity. Variations of the effective linewidth was qualitatively explained with the spin wave scattering theory.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.9
• /
• pp.450-455
• /
• 2001

We proposed a new sensitivity verification method for the UHF partial discharge(PD) detection system. Initially, we measure the UHF power induced by 5 pC PD which takes place near UHF sensor. Subsequently, we inject the swept UHF signal from a network analyzer into the GIS and measure the attenuation of the signal along the 71S Both the UHF power by 5 pC PD and the attenuation make it possible to verify the sensitivity and spatial coverage of the PD detection system. This method doesn\`t require the calibration of injected pulse type UHF signal into the GIS and makes us precisely measure the attenuation in frequency domain.