• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.8
• /
• pp.391-399
• /
• 1999

We have designed the backward wave oscillator, a power-pulsed generator oscillated at 20 GHz has higher frequency than current one. An absolute instability linear analysis was used for the purpose of designing the slow wave structure. A large diameter (D/$\lambda$=4.8) of the slow wave structure was adopted to prevent the breakdown brought about by the increase of power density. We have fabricated a marx generator, pulse forming line and diode. And the development of a compact pulsed power generator with short period and low amplitude is expected.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.135-136
• /
• 2008

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.11a
• /
• pp.39-40
• /
• 2007

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.663-666
• /
• 1998

A triangular/square waveforms generator with current controllable frequency is described. The genertor utilizes operational transconductance amplifiers as switching elements. The circuit built with commercially available components exhibits good linearity of current to frequency and relatively low temperature sensitivity.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.6
• /
• pp.579-585
• /
• 2009

The multifrequency eddy current testing(ECT) have been proposed various frequency mixing algorithms. In this study, we compare these approaches to frequency mixing of ECT signals from steam generator tubes; time-domain optimization, discrete cosine transform-domain optimization. Specifically, in this study, two different frequency mixing algorithms, a time-domain optimization method and a discrete cosine transform(DCT) optimization method, are investigated using the experimental signals captured from the ASME standard tube. The DCT domain optimization method is computationally fast but produces larger amount of residue.

• Journal of Power Electronics
• /
• v.8 no.1
• /
• pp.81-90
• /
• 2008

This paper presents an investigation of a voltage and frequency controller for an isolated asynchronous generator (IAG) driven. by a wind turbine and supplying 3-phase 4-wire loads to the isolated areas where a grid is not accessible. The control strategy is based on the indirect current control of the VSC (voltage source converter) using the frequency PI controller. The proposed controller consists of three single-phase IGBT (Insulated Gate Bipolar Junction Transistor) based VSC, which are connected to each phase of the IAG through three single phase transformers and a battery at their DC link. The controller has the capability of controlling reactive and active powers to regulate the magnitude and frequency of the generated voltage, harmonic elimination, load balancing and neutral current compensation. The proposed isolated system is modeled and simulated in MATLAB using Simulink and PSB (Power System Block-set) toolboxes to verify the performance of the controller.

• Proceedings of the KIPE Conference
• /
• 2017.11a
• /
• pp.63-64
• /
• 2017

This paper proposes a speed estimator for sensorless control of diesel-generator (genset) systems, where the speed of the genset is calculated from the back-EMF frequency of the generator. The back-EMF frequency is extracted from a phase output current by using multiple second-order generalized integrators (SOGIs) connected in parallel and series and separated frequency-locked loops. The proposed method (PS-SOGI-FLL) is able to estimate the fundamental frequency in the distorted output current with high accuracy and strong robustness. Simulation results are shown to verify the validity of the proposed method.

• Journal of Sensor Science and Technology
• /
• v.20 no.4
• /
• pp.238-242
• /
• 2011

This paper describes the fabrication and characteristics of a low frequency vibration driven electromagnetic energy harvester. The fabricated generator consists of a permanent magnet of NdFeB, a FR-4 planar spring and a Copper cylinder type coil. ANSYS modal analysis was used to determine the resonant frequency for the generator. The implemented generator is capable of producing up to 550 mV peak-to-peak under 7 Hz frequency, which has a maximum power of $95.5\;{\mu}W$ with load resistance of $580\;{\Omega}$. This device is shown to generate sufficient power at different resonating modes, and the experimental and simulated results are discussed and composed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.7
• /
• pp.978-983
• /
• 2015

This paper presents Frequency Bias setting for the adequate AGC(Automatic Generator Control) operation based on the frequency response of power system in Korea. AGC frequency control recovers the frequency up to 60Hz following a primary control when the frequency suddenly drops due to a fault in power system. AGC can compensate an appropriate amount of generation by calculating ACE(Are Control Error) from the frequency deviation with the AGC frequency bias set from the actual frequency response in power systems. An appropriateness of the proposed AGC bias setting is verified through case studies employing the simulation model.

• Journal of IKEEE
• /
• v.17 no.4
• /
• pp.537-543
• /
• 2013

This paper proposed a low EMI spread spectrum clock generator (SSCG) using discontinuous frequency modulation technique. The proposed SSCG is designed for triangular frequency modulation with high modulation depth. When the maximum time interval error (MTIE) of the SSCG is higher than given limit, the output frequency of SSCG is divided by two and used for reducing the time interval error (TIE). This discontinuous frequency modulation technique can effectively reduce the EMI within given limit. The simulated EMI of proposed SSCG was reduced by 18.5dB than that of conventional methods.