• Journal of Welding and Joining
• /
• 제19권4호
• /
• pp.391-398
• /
• 2001

MIAB welding method uses a rotating arc as its heat source and is known to be efficient in pipe butt welding. The arc is rotated around the weld line by the electro-magnetic force resulting from the interaction of arc current and magnetic field. This paper is concerned with the experiment of initial stage for process control, monitoring for weld quality, and the design of coil system which is efficient of flux generation and concentration. A coil system for the generation of magnetic flux was designed and constructed. Magnetic flux density and arc rotating behavior are important factors in MIAB welding, so the relations between these factors and process parameters were investigated. Various experiments were performed for the steel pipes(48.1mm O.D and 2.0mm thickness). The magnetic flux density is increased by increasing exciting current and decreasing gap size. The maximum of arc rotating frequency is affected by exciting current and gap size. However, the variations of arc rotating frequency during welding and then the melting process are mainly influenced by welding current. Thus, it is considered that the results of this study can be used as important data on the monitoring for weld quality and the design of efficient coil system.

• Journal of Plant Biology
• /
• 제5권1호
• /
• pp.1-6
• /
• 1962

1) Germination rate was rather irregular than decreasing as increasing dose of radiation and there were no differences between Kyong-Sam and Chuong-Bang of Chinese cabbage. 2) In R1 generation, abnormal leaves from seedling of irradiated seeds were observed. These were more apparent in X-ray irradiation than in thermal neutron. 3) Seedling height was inhibited with increasing dose of X-ray and thermal neutrons. Growth inhibition was more remarkable in X-ray than in thermal neutron. Kyong-Sam demonstrated more sensitivity than Chyong-Bang in both X-ray and thermal neutron. 4) Seedling height produced from seeds subjected to thermal neutrons showed small variation around its mean value, while in X-irradiation there was a greater deviaton from the mean value. 5) Fertility was decreased as increasing with dose, while the frequency of abortive pollen was increased. There were variability of the fertility and frequency of abortive pollen among plants or branches of a plant. 6) The mutants were obtained more in thermal neutron irradiation than in X-ray. The types of mutations obtained in Chinese radish of R2 generation were abnormal leaf, densely glowing leaf, degeneration in growing point and dwarf. The maximum frequency of phenotypic mutations was abnormal leaf mutation.

• Journal of Electrical Engineering and Technology
• /
• 제9권3호
• /
• pp.1119-1124
• /
• 2014

High temperature superconducting magnetic energy storage (HTS SMES) is known as an effective solution to significantly decrease the voltage and power fluctuations of grid connected wind power generation system (WPGS). This paper implements an effective control scheme of a back-toback converter with shunt-connected HTS SMES for the frequency regulation of an islanded microgrid. The back-to-back converter is used to connect the WPGS to the grid. A large-scale HTS SMES is linked to the DC side of the back-to-back converter through a two-quadrant DC/DC chopper. An adaptive control strategy is implemented for the back-to-back converter and the two-quadrant DC/DC chopper to improve the efficiency of the whole system. The performance of the proposed control system was evaluated in a test power system using PSCAD/EMTDC. The simulation results clearly show that the back-to-back converter with shunt-connected HTS SMES operates effectively with the proposed control strategy for stabilizing the power system frequency fluctuations.

• 한국정보통신학회논문지
• /
• 제17권5호
• /
• pp.1055-1063
• /
• 2013

전자파 내성 및 전자파 장해 측정을 위한 표준 전자파 발생 장치 중 하나인 CTL cell에서 두 개의 입력 단자에 동일 신호와 역위상 신호 입력에 따른 다양한 전계와 자계 발생에 대해 살펴보았다. 기본 공진주파수 TE011이 2.20GHz인 CTL cell을 이용하여 우세 전계장과 우세 자계장 조건에서 입력 전력의 변화에 따른 전계 특성, 측정 위치에 따른 전계 특성, 주파수 변화에 따른 전계 특성을 측정하였고, 이를 이용하여 CTL cell의 측정 영역에서의 동작 특성과 공진주파수의 영향을 받지 않고 사용 가능한 주파수 대역을 살펴보았다.

• 전기학회논문지
• /
• 제65권7호
• /
• pp.1161-1168
• /
• 2016

Battery energy storage system(BESS) attract the attention of the power system operators with its fast response to a disturbance in spite of its limited energy capacity. This paper proposes the operating method of BESS for following the Automatic Generation Control(AGC) frequency control which is centrally distributed by a system operator. As BESS needs to just meet the control requirement from the system operator, it should be able to properly manage the state of charge(SOC) of BESS to be available to control signal. For doing these, the proposed method distributes the control requirement to available batteries in proportion to its SOC. In addition, unavailable batteries are controlled to recover the SOC to an appropriate range, and the recovering power is supplied by available batteries meeting the control requirement. Moreover, the proposed method manages the efficiency of power conversion system (PCS) by limiting the number of PCS to be assigned for the low control requirement. Finally, the case studies are carried out to verify the effectiveness of proposed strategy.

• Journal of Electrical Engineering and Technology
• /
• 제6권4호
• /
• pp.439-446
• /
• 2011

Frequency is an important operating parameter for the protection, control, and stability of a power system. Thus, it must be maintained very close to its nominal frequency. Due to the sudden change in generation and loads or faults in a power system, however, frequency deviates from its nominal value. An accurate monitoring of the power frequency is essential for optimum operation and prevention of wide area blackout. Most conventional frequency estimation schemes are based on the DFT filter. In these schemes, the gain error could cause defects when the frequency deviates from the nominal value. We present an advanced frequency estimation technique using gain compensation to enhance the DFT filter-based technique. The proposed technique can reduce the gain error caused when the frequency deviates from the nominal value. Simulation studies are performed using both the data from EMTP-RV software and the user-defined arbitrary signals to demonstrate the effectiveness of the proposed algorithm. Results show that the proposed algorithm achieves good performance under both steady state tests and dynamic conditions.

• ETRI Journal
• /
• 제38권3호
• /
• pp.455-462
• /
• 2016

Frequency hopping (FH) is a common characteristic of a wide variety of communication systems. On the other hand, software-defined radio (SDR) is an increasingly utilized technology for implementing modern communication systems. The main challenge when trying to realize an SDR FH system is the frequency tuning time, that is, the higher the hopping rate, the lower the required frequency tuning time. In this paper, significant universal hardware driver tuning options (within GNU Radio software) are investigated to discover the tuning option that gives the minimum frequency tuning time. This paper proposes an improved SDR frequency tuning algorithm for the generation of a target signal (with a given target frequency). The proposed algorithm aims to improve the frequency tuning time without any frequency deviation, thus allowing the realization of modern communication systems with higher FH rates. Moreover, it presents the design and implementation of an original GNU Radio Companion block that utilizes the proposed algorithm. The target SDR platform is that of the Universal Software Radio Peripheral USRP-N210 paired with the RFX2400 daughter board. Our results show that the proposed algorithm achieves higher hopping rates of up to 5,000 hops/second.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -1
• /
• pp.381-384
• /
• 2002

Orthogonal Frequency Division Multiplexing (OFDM), which employs orthogonal overlapping subcarriers to modulate the signals, has been attracted much attention in recent time as a favorable option for future generation wireless networks due to its ability to overcome many impairments in wireless channels. Since OFDM is a multi-carrier system adaptive modulation techniques can be effectively and efficiently used to enhance the system performance in terms of both BER and overall system capacity. This paper discusses a COFDM-CDMA system with adaptive modulation schemes for future generation wireless networks.

• 대한전자공학회논문지
• /
• 제27권8호
• /
• pp.1221-1230
• /
• 1990

This paper presents a code generation method and an effective handling algorithm of ingeger constant multiplication for RISC machines in compiler design. As RISC Architectures usually use faster and more simply formed instructions than CISC's and most RISC processors do not have an integer multiplication instruction, it is required an effective algorithm to process integer multiplication. For the proposed code generator, Portable C Compiler(PCC) is redesigned to be suitable for an RISC machine, and composed an addition chain is built up to allow fast execution of constant multiplication, a part of integer one whicch appears very frequency in code generation phase.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -2
• /
• pp.735-738
• /
• 2002

This paper a new simple PWM (Pulse Width Modulation) signal generation based on modified relaxation oscillator is introduced. Its advantages of the proposed principle are that the precise PWM signal can be easily achieved with a high frequency range up to several megahertz and a low-voltage power supply. The proposed circuit can accept either voltage or current modulating signal. It is very suitable for developing into Integrated Circuits (ICs) form in communication applications. The simulation and experimental results are also depicted, they shown good agreement with theoretical anticipation.