• 전기의세계
• /
• v.28 no.9
• /
• pp.35-40
• /
• 1979

A grounded inductor is proposed which contains only one resistor and operational amplifier. The circuit uses the inherent frequency dependent characteristic of an amplifier to simulate the inductor. A parallel resonance circuit is constructed with the proposed circuit. It has been proved by the experimental results of the resonant circuit that the proposed circuit is equivalent to the grounded lossy inductor. The lossy inductor is imbedded in a passive bandstop prototype, and the resultant characteristic curve has been verified by the experiment.

• ETRI Journal
• /
• v.28 no.1
• /
• pp.115-118
• /
• 2006

In this letter, a simple model parameter extraction methodology for an on-chip spiral inductor is proposed based on a wide-band inductor model that incorporates parallel inductance and resistance to model skin and proximity effects, and capacitance to model the decrease in series resistance above the frequency near the peak quality factor. The wide-band inductor model does not require any frequency dependent elements, and model parameters can be extracted directly from the measured data with some curve fitting. The validity of the proposed model and parameter extraction methodology are verified with various size inductors fabricated using $0.18\;{\mu}m$ CMOS technology.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.4 no.2
• /
• pp.83-87
• /
• 2004

Phase noise performance and current consumption of Radio Frequency (RF) Voltage-Controlled Oscillator (VCO) are largely dependent on the Quality (Q) factor of inductor-capacitor (LC) tank. Because the Q-factor of LC tank is determined by on-chip spiral inductor, we designed, analyzed, and modeled on-chip differential inductor to enhance differential Q-factor, reduce current consumption and save silicon area. The simulated inductance is 3.3 nH and Q-factor is 15 at 2 GHz. Self-resonance frequency is as high as 13 GHz. To verify its use to RF applications, we designed 2 GHz differential LC VCO. The measurement result of phase noise is -112 dBc/Hz at an offset frequency of 100 kHz from a 2GHz carrier frequency. Tuning range is about 500 MHz (25%), and current consumption varies from 5mA to 8.4 mA using bias control technique. Implemented in $0.35-{\mu}m$ SiGe BiCMOS technology, the VCO occupies $400\;um{\times}800\;um$ of silicon area.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.8
• /
• pp.757-765
• /
• 2007

Enhanced PSPICE circuit model for vented-box loudspeaker system with lumped parameters was proposed to more accurately simulate real vented-box loudspeaker system. Frequency dependent parameters were used to model voice coil inductor. Acoustic pressure response curves and electrical impedance curves were simulated and investigated by PSPICE circuit model according to circuit parameters' variations. Finally, it was used to identify faults detection in woofers manufactured by unskilled persons.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.10
• /
• pp.983-992
• /
• 2007

It was proposed to identify Thiele Small Parameters for loudspeaker attached to closed-box using known dynamic mass of moving parts. Also, enhanced PSPICE circuit model for closed-box loudspeaker system was proposed to more accurately simulate real closed-box loudspeaker system. Frequency dependent parameters were used to model voice coil inductor. Acoustic pressure response curves and electrical impedance curves were simulated and investigated by PSPICE circuit model according to compensation filter's parameters. Finally, proposed method is expected to be utilized for identification of pseudo Thiele Small parameters of microspeaker.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.8
• /
• pp.641-644
• /
• 2009

We have studied on the microwave characteristics for the meander type inductors on the MgO substrates and $Al_2O_3$ substrates by employing 3-D high frequency simulation, respectively. Proper designs of meander type inductors were proposed and confirmed through the high frequency simulations, 5, 7, 9, 11, and 13 turns meander type inductors have been choose to analyze the electrical properties for the microwave passive component applications. The Al top electrodes have 282 nm length, 45 nm width, 100 nm thickness and 15 nm gap. The simulations were carried out from 50 MHz to 30 GHz, Frequency dependent inductances and quality factor were calculated by employing the equivalent circuit model of meander type inductors. The self resonances frequency of meander type inductor were shifted from high frequency to low frequency range as the number of the turn of inductors was increased. From the microwave simulations, the inductances and quality factors of meander type inductors were extracted through the scattering parameter.

• Composites Research
• /
• v.12 no.2
• /
• pp.1-9
• /
• 1999

The piezoelectric material connected to external electric networks possesses frequency dependent stiffness and loss factor which are also affected by the shunting circuit. The external electric networks are generally specialized for two shunting circuits: one is the case of a resistor alone and the other is the combination of a resistor and an inductor. For resistive shunting, the material properties exhibit frequency dependency similar to viscoelastic materials, but are much stiffer and more independent of temperature. Shunting with a resistor and inductor introduces an electrical resonance, which can change the characteristics of structural resonance optimally in a manner analogous to a PMD (proof mass damper). Passive damping enhancement of composite beam using piezoelectric material connected to external electrical networks is achieved and presented in this paper.

• The Journal of the Acoustical Society of Korea
• /
• v.26 no.6
• /
• pp.276-285
• /
• 2007

In this paper it was discussed and compared measured loudspeaker impedance curve with ones reconstructed by TS parameters estimated using four kinds of parameter estimation methods developed in frequency domain. Frequency dependent parameters were introduced and derived using least square error minimization technique. For known dynamic mass TS parameter estimation methods were reviewed and also proved non-uniqueness of these parameters by simulation method. Minimum phase transformation was adopted to derive phase information from magnitude of loudspeaker electrical impedance curve measured by one channel analyzer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.912-915
• /
• 2004

Inductors material utilized in the downsizing passive devices and Rf components requires the physical and electrical properties at given area such as inductors thickness reduction, inductance and q-factor increase, low leakage current and thermal stability. In this study, Spiral inductors on the $SiO_2/Si$(100) substrate were fabricated by the magnetron sputtering method. Cu thin film with the thickness of $2{\mu}m$ was deposited on the substrate. Also we fabricated square inductors through the wet chemical etching technique. The inductors are completely specified by the turn width and the spacing between spirals. Both the width and spacing between spirals were varied from 10 to $60{\mu}m$ and from 20 to $70{\mu}m$, respectively. Inductance and Q factor dependent on the RF frequency were investigated to analyze performance of inductor arrays

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.2105-2107
• /
• 2004

In this study, Spiral inductors on the $SiO_2$/Si(100) substrate were fabricated by the magnetron sputtering method. Cu thin film with the thickness of 2 ${\mu}m$ was deposited on the substrate. Also we fabricated square inductors through the wet chemical etching technique. The inductors are completely specified by the turn width and the spacing between spirals. Both the width and spacing between spirals were varied from 10 to 60 ${\mu}m$ and from 20 to 70 ${\mu}m$, respectively. Inductance and Q factor dependent on the RF frequency were investigated to analyze performance of inductor arrays. Also, We recommend that the reasonable Q-factors, spec's turns and thickness of the coil for inductors cab be set to be ideal condition.