• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권11호
• /
• pp.536-543
• /
• 2003

In this paper, we describe a unique self oscillating and mixing (SOM) down-converter design using a modified defected ground structure (DGS). The proposed SOM converter is consisted of self-oscillator, which can produce negative resistance and select resonance frequency, RF matching circuit, and IF low pass filter. As the advantage of this SOM converter can mix LO and RF signals as well as inducing LO signal with only one active device. it is designed as a simple structure and the low cost. Also, there is easy advantage to be applied in RFIC/MMIC technology because it offers excellent phase noise performance in spite of using micro-strip structure. The LO signal for the proposed SOM converter is designed at 1㎓ and RF frequency was chosen to be 800MHz. The achieved conversion loss and phase noise performances of the implemented SOM converter are 15㏈ and -95dBc/Hz at 100KHz offset frequency respectively. The equivalent circuit parameters for DGS are extracted by using a three dimensional EM simulator and simple circuit analysis method.

• 전력전자학회논문지
• /
• 제21권6호
• /
• pp.530-537
• /
• 2016

This work deals with a switching method for minimizing overcurrent in a three-phase interleaved bidirectional DC-DC converter with frequency modulation. Generally, a three-phase interleaved DC-DC converter is used to reduce a current ripple component. The combined operation of three-phase and two-phase converters can significantly reduce the ripple component. However, the conventional PWM method cannot solve severe overcurrent during phase transfer or frequency variation for power control. To overcome this problem, this work proposes a new PWM switching method. A 3 kW DC-DC power converter is designed and implemented, and the converter is operated in discontinuous current mode with varying switching frequencies for power control. Simulation and experimental results show the validity of the proposed switching method. The proposed switching method can be widely used in the field of current ripple reduction for three-phase interleaved bidirectional DC-DC converters.

• 전력전자학회논문지
• /
• 제21권2호
• /
• pp.111-116
• /
• 2016

This paper proposes a high-frequency (MHz) LLC resonant converter for a capacitor coupling wireless power transfer (CCWPT). The CCWPT uses electric field in the coupling capacitor between the transmitter and receiver electrodes with a dielectric layer. Given that capacitance is very small and the impedance is large, transferring power with a simple series resonance is difficult. Therefore, the high frequency (MHz) and high Q factor LLC converter is proposed to reduce the impedance of the coupling capacitance and to obtain a high output voltage. This paper deals with the operation analysis of the proposed LLC converter and a theoretical capacitance estimation. The operation and features of the proposed CCWPT LLC converter is verified with a 4.2 W prototype for charging mobile devices.

• 한국전자통신학회논문지
• /
• 제7권6호
• /
• pp.1315-1320
• /
• 2012

본 연구에서는 분극의 이방성이 없는 ring-dot형 적층형 압전 변압기를 이용한 압전 AC-DC 컨버터를 개발하였다. 동작주파수 범위가 매우 좁은 압전 변압기의 특성을 고려하여 압전 컨버터는 발진주파수의 피드백 제어를 위한 PFM 구동방식과 출력제어를 위한 PWM 구동방식을 이용한 혼합형 구조로 설계되었다. 개발된 압전 컨버터의 최소 발열을 동반하는 안정적 구동을 보이는 최대전력 값은 25W였으며 허용전류 값은 약 900mA이었다. 압전 컨버터의 출력전압의 크기는 구동 발진주파수의 크기에 따라 제어가 가능하였으며, 최대전력에서 효율적이고 안정적인 동작특성을 나타내었다.

• Journal of Power Electronics
• /
• 제15권4호
• /
• pp.939-950
• /
• 2015

A single-stage AC-AC converter has been designed for a wind energy conversion system (WECS) that eliminates multistage operation and DC-link filter elements, thus resolving size, weight, and reliability issues. A simple switching strategy is used to control the switches that changes the variable-frequency AC output of an electrical generator to a constant-frequency supply to feed into a distributed electrical load/grid. In addition, a modified random sinusoidal pulse width modulation (RSPWM) technique has been developed for the designed converter to make the overall system more efficient by increasing generating power capacity and reducing the effects of inter-harmonics and sub-harmonics generated in the WECS. The technique uses carrier and reference waves of variable switching frequency to calculate the firing angles of the switches of the converter so that the three-phase output voltage of the converter is very close to a sine wave with reduced THD. A comparison of the performance of the proposed RSPWM technique with the conventional SPWM demonstrated that the power generated by a turbine in the proposed approximately increased by 5% to 10% and THD reduces by 40% both in voltage and current with respect to conventional SPWM.

• Journal of Electrical Engineering and Technology
• /
• 제6권6호
• /
• pp.842-848
• /
• 2011

The current study proposes the design of a hybrid series-parallel resonant converter (SPRC) and a three-stage Cockcroft-Walton voltage multiplier for precisely adjusting the power generated by a continuous wave (CW) $CO_2$ laser. The design of a hybrid SPRC, called LCC resonant converter, is described, and the fundamental approximation of a high-voltage and high-frequency (HVHF) transformer with a resonant tank is discussed. The results of the current study show that the voltage drop and ripple of a three-stage Cockcroft-Walton voltage multiplier depend on frequency. The power generated by a CW $CO_2$ laser can be precisely adjusted by a variable-frequency controller using a DSP (TMS320F2812) microprocessor. The proposed LCC converter could be used to obtain a maximum laser output power of 23 W. Moreover, it could precisely adjust the laser output power within 4.3 to 23 W at an operating frequency range of 187.5 to 370 kHz. The maximum efficiency of the $CO_2$ laser system is approximately 16.5%, and the minimum ripple of output voltage is about 1.62%.

• Journal of Electrical Engineering and Technology
• /
• 제11권2호
• /
• pp.383-392
• /
• 2016

This paper proposes the design considerations of resonant network and transformer magnetics for 500 kHz high switching frequency LLC resonant converter. The high power density can be effectively achieved by adopting high switching frequency which allows small size passive components in the converter. The design methodology of magnetizing inductance is derived for zero voltage switching (ZVS) condition, and the design methodology of the transformer and output capacitance is derived to achieve high power density at high operating frequency. Moreover, the structure of transformer is analyzed to obtain the proper inductance value for high switching operation. To verify the proposed design methodology, simulation and experimental results will be presented including temperature of passive and active components, and power conversion efficiency to evaluate dominant power loss. In addition, the validity of magnetics design will be evaluated with operating waveforms of the prototype converter.

• 조명전기설비학회논문지
• /
• 제20권1호
• /
• pp.119-124
• /
• 2006

본 논문은 고주파 절연형 소프트 스위칭 PWM DC-DC 컨버터의 효율을 높일 수 있는 새로운 회로를 제안하였다. 제안한 DC-DC 컨버터는 고주파 변압기의 여자전류를 이용하지 않고 인덕턴스를 이용하였다. 그리고 고주파 절연 변압기 2차측에 동기 정류용 전력용 MOSFET에 새로운 기능을 부가한 온-오프 제어 방식을 이용하여 넓은 부하 범위에 걸쳐 안정된 영전압 스위칭(ZVS)동작을 실현하였다. 그 결과 제안한 DC-DC 컨버터의 실험 장치에 의해서 효율을 97[%]이상 달성하였다.

• Journal of Power Electronics
• /
• 제14권6호
• /
• pp.1166-1177
• /
• 2014

A new type of topology with medium-frequency-transformer (MFT) isolation for medium voltage wind power generation systems is proposed in this paper. This type of converter is a high density power conversion system, with high performance features suitable for next generation wind power systems in either on-shore or off-shore applications. The proposed topology employs single-phase cascaded multi-level AC-AC converters on the grid side and three phase matrix converters on the generator side, which are interfaced by medium frequency transformers. This avoids DC-Link electrolytic capacitors and/or resonant L-C components in the power flow path thereby improving the power density and system reliability. Several configurations are given to fit different applications. The modulation and control strategy has been detailed. As two important part of the whole system, a novel single phase AC-AC converter topology with its reliable six-step switching technique and a novel symmetrical 11-segment modulation strategy for two stage matrix converter (TSMC) is proposed at the special situation of medium frequency chopping. The validity of the proposed concept has been verified by simulation results and experiment waveforms from a scaled down laboratory prototype.

• 전력전자학회논문지
• /
• 제22권4호
• /
• pp.345-352
• /
• 2017

In this paper, a non-dissipative snubber for reducing the switching losses in the step down converter is proposed. The conventional step down converter, e.g., buck converter, suffers from serious switching losses and consequentially heat generation because of its hard switching. Thus, it is unsuitable for high switching frequency operation. Reduction of the reactive components' size, such as an output inductor and capacitor, is difficult. The proposed snubber can slow down the increasing current slopes and switch voltage at turn-on and turn-off transients, thereby significantly reducing the switching loses. Additionally, the slowly increasing current during switch turn-on transition, can effectively solve the output rectifier diode reverse recovery problem. Therefore, the proposed non-dissipative snubber not only leads to the efficiency of converter operation at high switching frequency but also reduces the reactive components size in proportion to the switching frequency. To confirm the validity of the proposed circuit, theoretical analysis and experimental results from a 150 W, 1 MHz prototype are presented.