• Journal of the Korean Geotechnical Society
• /
• 제36권8호
• /
• pp.49-60
• /
• 2020

A fully coupled thermo-hydro-mechanical model is established to evaluate frost heave behaviour of saturated frost-susceptible soils. The method is based on mass conservation, energy conservation, and force equilibrium equations, which are fully coupled with each other. These equations consider various physical phenomena during one-dimensional soil freezing such as latent heat of phase change, thermal conductivity changes, pore water migration, and the accompanying mechanical deformation. Using the thermo-hydro-mechanical model, a sensitivity analysis study is conducted to examine the effects of the geotechnical parameters and external conditions on the amount of frost heave and frost heaving rate. According to the results of the sensitivity analysis, initial void ratio significantly affects each objective as an individual parameter, whereas soil particle thermal conductivity and temperature gradient affect frost heave behaviour to a greater degree when applied simultaneously. The factors considered in this study are the main factors affecting the frost heaving amount and rate, which may be used to determine the frostbite sensitivity of a new sample.

• Asian-Australasian Journal of Animal Sciences
• /
• 제21권5호
• /
• pp.738-744
• /
• 2008

In most developing countries consumers purchase retail cuts from hot carcasses and prepare traditional meat products as per their convenience and requirements. In this study, effects of different post mortem handling practices on quality of meat curry from culled sheep meat have been studied. After slaughter, leg cuts were subjected to nine commonly prevalent handling conditions in India viz. deboning (boning out) and cooking within 2-3 h (1), deboning immediately and cooking after 5-6 h (2), deboning after 5-6 h and cooking (3), deboning immediately, storage at $4^{\circ}C$ for 24 h and cooking (4), chilling for 24 h at $4^{\circ}C$, deboning and cooking (5), deboning after 5-6 h, storage for 24 h at $4^{\circ}C$, and cooking (6), deboning after 5-6 h, storage for 48 h at 4??C and cooking (7), deboning after 5-6 h, freezing and cooking (8), deboning after 5-6 h, storage for 24 h at $4^{\circ}C$, freezing and cooking (9). Significant differences were observed in pH, water-holding capacity, cooking loss and shear force values. Sensory scores were significantly higher in conditions (1), (5) and (9), and significantly lower in conditions (4) and (6). From the results, it was concluded that, to have the best quality product, meat should be cooked either immediately after slaughter or should be deboned just before cooking. Storage of deboned meat at refrigerated temperature must be avoided.

• Journal of the East Asian Society of Dietary Life
• /
• 제20권4호
• /
• pp.560-566
• /
• 2010

In this study, the effects of the chilling process after thawing on pork quality were investigated by comparing the physiochemical properties and palatability of the samples just after thawing(0-TP) and the other chilled at $2^{\circ}C$ for two days after thawing (2-TP). The samples used for this study were obtained from vacuum packaged frozen loin from crossbred black pigs reared on Jeju island, and frozen at $-20^{\circ}C$ for 1 month and 12 months, and then thawing them at $4^{\circ}C$ for 20 hours. In the case of loin that was thawed after freezing for 1 month, 2-TP showed a higher water holding capacity and myofibril fragmentation index, lower hardness and chewiness, as well as better juiciness and palatability than 0-TP. However, effects of chilling after thawing were not significant in the case of loin that had been frozen for 12 months.

• Journal of the Korea Institute of Building Construction
• /
• 제3권2호
• /
• pp.129-134
• /
• 2003

In this research, we used fly-ash and blast-furnace slag as substitute material of cement and fine aggregate, and we, through experiments, researched and analyzed the features of high-flowable concrete added high efficiency AE water reduction agent. The results are below. 1. Liquefaction generally presented high-slump flow value; on the other hand, partial segregation was observed in case of mixing proportion with 65 cm slump flow and above. This segregation was partially improved in accordance with mixing admixture. 2. Compressive strength according to mixing admixture and increasing mixing ratio of fly-ash were subject to be declined when it was initially cast-in, but its gap was improved when time was fully passed. 3. After mixing blast-furnace slag and fly-ash as substitute material, the result showed that the modulus of elasticity against freezing & melting was improved according to mixing blast-furnace slag and also increased in accordance with increasing pulverulent-body volume. 4. According to increasing the mixing volume of fly-ash, the durability factor was deteriorated because compressive strength became lower as well as air content was decreased when it was initially case-in. 5. The minimum air content to secure durability was 3.7%, for that reason, we had better secure admixture such as air entraining agent when cast-in high-flowable concrete.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• 제8권2호
• /
• pp.147-154
• /
• 1988

Korea has the ground which freezes in winter and melts in warmer seasons by turns. Therefore, in designing civil-structures or buildings on such ground, the depth of seasonal frost penetratio must be considered. In this paper, approximate contours of the maximum depth of frost penetration in Korea is presented. It was found that the maximum depth of frost penetration did not have the linear relationship to square root of the freezing index. In order to establish more reliable method to estimate the maximum depth of frost penetration, a new empirical equation is introduced. In the presented equation, the dry unit weight and water content of soil are considered in addition to the freezing index. And the equation is compared with other previous equations used so far.

• International Journal of Highway Engineering
• /
• 제18권1호
• /
• pp.43-55
• /
• 2016

PURPOSES : This study aims to develop a repair material that can enhance pavement performance, inducing rapid traffic opening through early strength development and fast setting time by utilizing MgO-based patching materials for repairing road pavements. METHODS : To consider the applicability of MgO-based patching materials for repairing domestic road pavements, first, strength development and setting time of the materials were evaluated, based on MgO to $KH_2PO_4$ ratio, water to binder ratio, and addition ratio of retarder (Borax), by which the optimal mixture ratio of the developed material was obtained. To validate the performance of the developed material as a repair material, the strength(compressive strength and bonding strength) and durability (freezing, thawing, and chloride ion penetration resistance) was checked through testing, and its applicability was evaluated. RESULTS : The results showed that when an MgO-based patching material was used, the condensation time was reduced by 80%, and the compressive strength was enhanced by approximately 300%, as compared to existing cement-based repair materials. In addition, it was observed that the strength (compressive strength and bonding strength) and durability (freezing and thawing, and chloride ion penetration resistance) showed an excellent performance that satisfied the regulations. CONCLUSIONS : The results imply that an emergent repair/restoration could be covered by a rapid-hardening cement to meet the traffic limitation (i.e. the traffic restriction is only several hours for repair treatment). Furthermore, MgO-based patching materials can improve bonding strength and durability compared to existing repair materials.

• KSBB Journal
• /
• 제14권1호
• /
• pp.51-57
• /
• 1999

The immobilization of nitrifier consortium was carried out for the application to recirculating aquaculture system(RAS). The abilities of $NH_4^+$-N removal by immobilized nitrifier consortia prepared with boric acid treated, ethanol treated, ad freezing-thawing treated PVA beads at the concentration 15% were examined. To identify the possibility of applying the beads in the fluidized bed reactor, characteristics of beads were evaluated. The suitable bead was boric acid treated beads which had highest ammonia removal rate of 16.09 g/$m^3$/day. It took 12 days for nitrifier consortium immobilized beads to be stable for the removal of $NH_4^+$-N. Life spans of the beads were more than three months with aggressive aeration in the fluidized ed reactor when nitrifier consortia immobilized in PVA beads were used. In order to apply the nitrifier consortium immobilized beads to aquaculture facility, the continuous reactor was used for 49 days with synthetic aquacultural water containing 2 mg/L ammonia. The highest ammonia removal rate of 31.87 g/$m^3$/day was observed when hydraulic residence time was 0.6 hour(36min.).

• Magazine of the Korea Concrete Institute
• /
• 제7권4호
• /
• pp.149-156
• /
• 1995

The fracture process zone in concrete is a region ahead of a traction-free crack, in which two major mechanisms, microcracking and bridging, play important roles. The toughness due to bridging is dominant compared to toughness induced by microcracking, so that the bridging is dominani: mechanism governing the fracture process of concrete. Fracture mechanics does work for concrete provided that the fracture process zone is being considered, so that the development of model for the fracture process zone is most important to describe fracture phenomena in concrete. In this paper the bridging zone, which is a part of extended rnacrocrack with stresses transmitted by aggregates in concrete, is modelled by a Dugdale-Barenblatt type model with linear tension-softening curve. Two finite element techniques are shown for the analysis of progressive cracking in concrete based on the discrete crack approach: one with crack element, the other without crack element. The advantage of the technique with crack element is that it dees not need to update the mesh topology to follow the progressive cracking. Numerical results by the techniques are demonstrated.

• International Journal of Highway Engineering
• /
• 제15권4호
• /
• pp.53-63
• /
• 2013

PURPOSES: The purpose of this study was to investigate the disintegration mechanism of concrete due to the infiltration of the moisture to the milling overlay pavement and to come up with a method to minimize the disintegration as well as verifying the effectiveness of the edge sealing and Fogseal method. METHODS : This study investigated the distress mechanism due to the infiltrated moisture remaining in the milling overlay pavement through chloride freezing test and verified the effectiveness of the sealing of the milling edge and fog seal methods, which have been devised to minimize the moisture infiltration, through laboratory water permeability test. Additionally, long-term pavement performance was compared for the effectiveness of the proposed method through under loading test, and field water permeability test was carried out to verify the field applicability of the proposed method. RESULTS: The result of the research confirmed that chloride deteriorates the concrete surface through disintegration and lowers its strength and that the laboratory moisture infiltration test verified the effectiveness of the milling edge sealing and fog seal methods in the deterrence of moisture infiltration to the overlay pavement with excellent long-term performance of the pavement treated with the proposed method. Although the field water permeability test revealed some deterrence of moisture infiltration of the milling edge sealing and fog seal methods to a certain extent, the difference was a little. CONCLUSIONS: The milling edge sealing and fog seal methods are limited in their effectiveness for the cases of improvident compaction management or mixture with large void, and it is believed that installation of subsurface drainage is more effective in these cases.

• Progress in Superconductivity and Cryogenics
• /
• 제21권1호
• /
• pp.40-44
• /
• 2019

This study investigates mixtures of water and cryoprotectant agents (CPAs) to store high-grade cold energy. Although water is an ideal material for a cold thermal storage (CTS) due to its high specific heat, undesirable volume expansion may cause structural stresses during freezing. The volume expansion can be alleviated by adding the CPAs to water. However, the CPA aqueous solutions not only have different thermal properties but also transit to amorphous state different from pure water. Therefore, these characteristics should be considered when using them as material of the CTS. In experiments, glycerol and dimethyl sulfoxide (DMSO) are selected as the candidate CPA. The volume expansion of the solution is measured by an in-situ strain gauge in low temperature region. The specific heat capacity of the solution is also measured by differential scanning calorimetry (DSC). Both the amount of volume expansion and the specific heat capacity of the CPA aqueous solution decrease in the case of higher concentration of CPA. These characteristics should be contemplated to select optimal aqueous solution for CTS for liquid air energy storage system (LAES). The CPA solutions have advantages of having wide temperature range to utilize the latent heat of water and higher sensible heat of the CPA. The CPA solutions which can satisfy the allowable stress of the structure are determined. Consequently, among the CPA solutions investigated, DMSO 20% w/w solution is the most suitable for the CTS.