• 한국환경농학회지
• /
• 제24권1호
• /
• pp.6-11
• /
• 2005

A prototype surface flow constructed wetland was built in the upstream area of reclaimed tidal lands to improve the water quality of Lake Sihwa by treating severely polluted stream water. In this study, a tracer test using rhodamine-WT was performed to investigate the flow characteristics and to quantify the observed hydraulic residence time (HRT) for a high-lying cell in the Banwol wetland of the Sihwa constructed wetland. The tracer test indicated that even if flow was mainly observed in the open water area of the Banwol wetland, water flowed continuously in the vegetative area and there was no dead zone. The calculated HRT (51.3 hrs), calculated by dividing the wetland volume by the wetland inflow, exceeded the observed HRT (38.7 hrs), since the short-circuiting of flux resulting from irregular topography and vegetation was not reflected in the calculated HRT. The exit tracer concentration curves were reproduced well by both the plug flow with dispersion and tanks-in-series models, indicating that the performance of the Banwol wetland can be estimated accurately using these models.

• 대한기계학회논문집B
• /
• 제23권7호
• /
• pp.864-870
• /
• 1999

An experimental study Is conducted in a four-vane linear cascade in order to examine the influence of the wake behind rectangular bars on the flow and heat transfer characteristics. Flow and heat transfer measurements are made for the inlet Reynolds number of 66000(based on chord length and free-stream velocity). Turbulent intensity and stress are measured using a hot-wire anemometer, and to measure the convective heat transfer coefficients on the blade surface liquid crystal/gold film Intrex technique is used. Each of experimental cases is characterized by the unsteadiness measured at the entrance of the cascade. The wake behind the rectangular bars enhances the turbulent motion of the flow in the cascade passage. It also promotes the boundary layer development and transition. The results show that heat transfer coefficients on the blade surface increase with increasing unsteadiness.

• Environmental Engineering Research
• /
• 제23권4호
• /
• pp.390-396
• /
• 2018

This study investigated the transformation of dissolved organic matter (DOM) in a free-water surface flow constructed wetland. Pyrolysis gas chromatography-mass spectrometry (Py-GC/MS) coupled with preparative high-performance liquid chromatography (prep-HPLC) was used to analyze the compositions of biopolymers (polysaccharides, amino sugars, proteins, polyhydroxy aromatics, lipids and lignin) in DOM according to the molecular size at three sampling points of the water flow: inflow, midflow, and outflow. The prep-HPLC results verified the decomposition of DOM through the decrease in the number of peaks from three to one in the chromatograms of the sampling points. The Py-GC/MS results for the degradable peaks indicated that biopolymers relating to polysaccharides and proteins gradually biodegraded with the water flow. On the other hand, the recalcitrant organic fraction (the remaining peak) in the outflow showed a relatively high concentration of aromatic compounds. Therefore, the ecological processes in the constructed wetland caused DOM to become more aromatic and homogeneous. This indicated that the constructed wetland can be an effective buffer area for releasing biochemically stable DOM, which has less influence on biological water quality indicators, e.g., biochemical oxygen demand, into an aquatic ecosystem.

• 소음진동
• /
• 제6권5호
• /
• pp.671-677
• /
• 1996

This paper presents the analytical method for predicting turbulence- induced noise in the multilayered cylinder composed of an outer hose, an inner fluid and an internal core. It is assumed that an infinite axisymmetric cylinder is located horizontally in water with free stream velocity and the turbulent boundary layer (TBL) surrounding the outer hose is fully developed and homogeneous. The transfer function at the core surface due to the propagation of the pressure fluctuation within the TBL is formulated using the linearized Navier-Stockes equation for solid and fluid. In the estimation of the energy spectrum of wall pressure fluctuation, the empirical formula proposed by Strawderman based on the Corcos model is used. A general algorithm for the calculation of the pressure level at the surface of a core, that is, turbulence- induced noise, is presented. Through the detailed numerical simulation, it is found that the major noise mechanism is the propagation of the bulge wave along hose.

• 한국주조공학회지
• /
• 제15권4호
• /
• pp.408-415
• /
• 1995

Polycrystalline Al-Cu ribbons were produced by planar flow casting(PFC). Solidification behavior and microstructual changes of the ribbons have been investigated as a function of ribbon thickness and processing parameters. The solidification front velocity, V varies within the ribbon, decreasing with increasing the distance, S from the wheel-contact surface, as $V=17.6S^{-1}$. In Al-4.5wt%Cu alloy, rapid decrease in solidification velocity toward the free surface causes a change in solidification morphology from planar to cellular, and finally, to dendritic. The length and inclination of columnar grains solidified with planar front were related to the wheel velocity. The transition from particulate degenerate eutectic structure to regular lamellar eutectic structure was observed to be caused by a difference of the relative growth velocites of ${\alpha}-Al$ and ${\theta}$ during solidification in the Al-Cu eutectic alloy.

• 한국정밀공학회지
• /
• 제15권4호
• /
• pp.148-155
• /
• 1998

It is commonly known that, in GMAW, the characteristics of metal transfer and the size of molten drop are highly dependent on the welding current. These changes in the characteristics of metal transfer has a considerable effect on the weld quality, and a lot of studies have been made on metal transfer modes for that reason. In this study, two cases were investigated; the one in which the metal transfer proceeds with gravitational force, surface tension, and no electromagnetic force, and the other in which the process has electromagnetic term in addition, where the current density in the fluid has been assumed to have Gaussian distribution on any given cross-section and it acts vertically. Using fluid flow analysis, this study has observed the whole process of the development and break-up of the molten drop, and it also showed that transitional processes, drop rate, and the drop size in each metal transfer mode can be estimated.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.676-681
• /
• 2001

In this paper, the spin-up from rest to a state of solid-body rotation in a circular container with a slender rectangular obstacle on the bottom wall is analysed experimentally. We use a PIV method for the evolution of the free-surface flow. Laboratory experiments have been carried out for a variety of the obstacle height h(0, 5, 10 [mm]) and the liquid depth H(25, 50, 75, 100 [mm]). It was found that the spin-up time is crucially dependent on the obstacle height T. In the case of T=10[mm] the spin-up time is considerably shorter then the other cases.

• Journal of Mechanical Science and Technology
• /
• 제20권6호
• /
• pp.882-895
• /
• 2006

Surface and interfacial waves in two superposed horizontal inviscid fluids of finite depths are studied. The flow is induced by translating a vertical rigid plate with a prescribed velocity. Analytical solutions that accurately predict the motion of the free surface and the interface are obtained by using a small-Froude-number approximation. Three different velocities of the plate are considered, while flows induced by any arbitrary motion of the plate can be easily analyzed by a linear superposition of the solutions obtained. It is shown that pinching of the upper layer can occur for a sufficiently thin upper layer, which leads to its rupture into small segments. Other interesting phenomena, such as primary and secondary wiggles generated on the interface near the wavemaker, are discussed.

• 물과 미래
• /
• 제23권2호
• /
• pp.251-263
• /
• 1990

본 연구의 목적은 도시 유역에서의 표면유출에 의한 맨홀 유입량을 추정하고 관망에서의 흐름을 해석하기 위한 모형을 개발하기 위한 것이다. 각 맨홀로의 유입량은 합리식을 이용한 단순방법으로 유입 수문곡선을 모의하는 방법과 해당유역 특성을 고려한 표면유출 모의에 의한 유입 수물곡선 결정방법이 이용된다. 관망에서의 흐름은 Saint-Venant공식의 dynamic equation에 유한음차분법(four-point implicit method)응 적용하여 동시해법으로 해석하였다. 특히 압력류(surcharge flow)흐름은 관의 상단에 좁고 긴 가상관을 연결시켜 모든 흐름을 개수로 흐름으로 해석가능 하도록 전환함으로써 해석의 단순화를 기하였고, 개발된 USS-slot모형이 부정류 우수관망 흐름을 적절히 모의할 수 있는가를 판별하기 위하여 기존에 연구된 관망에 적용하여 그 결과들을 비교 분석하였다.

• 한국자기학회지
• /
• 제25권1호
• /
• pp.4-9
• /
• 2015

본 연구는 PFC(Planar Flow Casting)프로세스에 의한 Fe기 $Fe_{78}Si_9B_{13}$ 비정질 합금리본 제조에 있어서 습도변화(55~85 %)가 비정질 합금리본의 표면결함 및 자기적 특성에 미치는 영향을 조사하였다. 그 결과, 비정질 합금리본의 접촉면과 자유면에서 관찰된 air pocket/droplet의 크기는 습도가 증가할수록 커지는 경향을 보임과 동시에 표면조도과 함께 크게 증가하였으며, 특히 습도 65 %에서 제조한 표면조도 값이 접촉면($Ra=0.60{\mu}m$, $Rz=3.11{\mu}m$)과 자유면($Ra=0.47{\mu}m$, $Rz=3.00{\mu}m$)에서 모두 가장 낮은 값이 얻어졌다. 또한 $23(OD)^*20(ID)^*20(H)$ 크기의 토로이달 코어로 제조된 자성코어의 연자기적 특성의 경우에도 65 %에서 제조한 비정질 합금리본의 시료에서 $B_s(B_{700})=1.055T$, $H_c=0.083Oe$, 투자율 = 1,197 및 core loss = 0.276 W/kg로 가장 우수한 값이 얻어졌다.