• Journal of the Society of Naval Architects of Korea
• /
• v.50 no.5
• /
• pp.282-290
• /
• 2013

The effects of the combination of blade number for forward and after propeller on the propeller shaft forces of a contra-rotating propeller (CRP) system are presented in the paper. The research is performed through the numerical simulations based on the Reynolds-Averaged Navier-Stokes equations (RANS). The simulation results of the present method in open water condition are validated comparing with the experimental data as well as the other numerical simulation results based on the potential method for 4-0-4 CRP (3686+3687A) and 4-0-5 CRP (3686+3849) of DTNSRDC. Two sets of CRP are designed and simulated to study the effect of the combination of blade number in behind-hull condition. One set consists of 3-blade and 4-blade, while the other is 4-blade and 4-blade. A full hull body submerged under the free surface is modeled in the computational domain to simulate directly the wake field of the ship at the propeller plane. From the simulation results, the fluctuations of axial force and moment are dominant in the case of same blade numbers for forward and after propellers, whereas the fluctuations of horizontal and vertical forces and moments are very large in the case of different blade numbers.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.26 no.3
• /
• pp.29-40
• /
• 1989

A new blade section of propeller is developed to obtain higher propeller efficiency and better cavitation performance. Eleven foil sections are carefully designed and manufactured to compare the lift-drag characteristics and cavitation performances. It is expected that the developed section behaves better in the vicinity of the ship's wake, where the angle of attack variation is large, because of its wider width in lift-drag and cavitation-free bucket diagrams. A propeller design method using the selected foil section is presented. Three chordwise loading shapes are selected to investigate the influence of the lift-drag ratios on the propeller efficiencies and cavitation performances. Three propellers are designed, which correspond to the selected chordwise loading shapes. Two more propellers which use existing foil sections are designed to compare the section performance.

• Journal of the Society of Naval Architects of Korea
• /
• v.28 no.2
• /
• pp.40-51
• /
• 1991

A Propeller design method using the newly developed blade section(KH18), which behaves better cavitation characteristics, is presented. Experimental results for two-dimensional foil sections show that the lift-drag curve and the cavitation-free bucket diagram of the new blade section are wider comparing to those of the existion NACA sections. This characteristic of the new section is particularly important for marine propeller applications since angle of attack variation of the propeller blade operating behind a non-uniform ship's wake is relatively large. A lifting surface theory is used for the design of a propeller with the developed section for a 2700 TEU container ship. Since the most suitable chordwise loading shape is not known a priori, chordwise loading shape is chosen as a design parameter. Five propellers with different chordwise loading shapes and different foil sections are designed and tested in the towing tank and cavitation tunnel at KRISO. It is observed by a series of extensive model tsets that the propeller(KP197) having the chordwise loading shape, which has less leading edge loading at the inner radii and more leading edge loading at the outer radii of 0.7 radius, has higher propulsive efficiency and better cavitation characteristics. The KP197 propeller shows 1% higher efficiency, 30% cavitation volume reduction and 9% reduction of fluctuating pressure level comparing to the propeller with an NACA section. More appreciable efficiency gain for the new blade section propeller would be expected by reduction of expanded blade area considering the better cavitation characteristics of the new blade section.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.6
• /
• pp.516-525
• /
• 2015

In this paper, the acoustic pressure of a helicopter rotor in hovering and low speed descent flight is predicted and compared with experimental data. Ffowcs Williams-Hawkings equation is used to predict the acoustic pressure. Two different wind tunnel test data are used to validate the predicted results. Boeing 360 model rotor test results are used for the low-frequency noise in hover, and HART II test results are employed for the mid-frequency noise, especially BVI noise, in low speed descent flight. A simple free-wake model as well as the state-of-the-art CFD/CSD coupling method are adopted to perform the analysis. Numerical results show good agreement against the measured data for both low-frequency and mid-frequency harmonic noise signal. The noise carpet results predicted using the FFT(Fast Fourier Transform) shows also reasonable correlation with the measured data.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.3
• /
• pp.222-232
• /
• 2011

This article examines the scale effect of the flow characteristics, resistance and propulsion performance on a 317k VLCC. The turbulent flows around a ship in both towing and self-propulsion conditions are analyzed by solving the Reynolds-averaged Navier-Stokes equation together with the application of Reynolds stress turbulence model. The computations are carried out in both model- and full-scale. A double-body model is applied for the treatment of free surface. An asymmetric body-force propeller is used. The speed performances including resistance and propulsion factors are obtained from two kinds of methods. One is to analyze the computational results in model scale through the revised ITTC' 78 method. The other is directly to analyze the computational results in full scale. Based on the computational predictions, scale effects of the resistance and the self-propulsion factors including form factor, thrust deduction fraction, effective wake fraction and various efficiencies are investigated. Scale effects of the streamline pattern, hull pressure and local flow characteristics including x-constant sections, propeller and center plane, and transom region are also investigated. This study presents a useful tool to hull-form and propeller designers, and towing-tank experimenters to take the scale effect into consideration.

• Journal of Korea Water Resources Association
• /
• v.38 no.11
• /
• pp.917-925
• /
• 2005

LSIV (Large Scale Image Velcocimetry) Is one of the image-based velocity measurement techniques. Since it measures surface velocities, it gives simple and inexpensive way to measure velocity, compared to other methods. Because of these advantages, there have been many studies to apply LSIV to the river discharge measurement in the field. Measuring the discharge by using LSIV requires a method which converts a surface velocity to a mean velocity In the present study, experiments and analysis of vortical velocity profile of open-channel flow in various conditions were performed to develop methods which estimate a mean velocity from a surface velocity. The result of this experiment reveals that velocity-dip phenomena occur at free-surface layer in open channel flow and Froude number affects more than bed roughness does. Two methods for estimating the mean velocity were proposed. One is to correct the wake law's profiles by using the difference of surface velocity from the mean velocity, and the other is to use the ratio of mean and surface velocities. The result of applying these methods in an experiment shows that they are quite accurate having an error of approximately $6\%$ only.