• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.1
• /
• pp.72-77
• /
• 2014

There are two main technologies to implement cloud effect in flight simulator, cloud modeling using particle system and texture mapping. In former case, this approach may cause a low frame rate while unrealistic cloud effect is observed in latter case. To Solve this problem, in this paper, we propose how to apply fog effect into camera to display more realistic cloud effect with high frame rate. The proposed method is tested with massive terrain database environment through implemented software by using OpenSceneGraph. As a result, compared to texture mapping method, the degree of difference on frame rate is 1 or 2Hz while the cloud effect is significantly improved as realistic as particle system.

• The Journal of the Acoustical Society of Korea
• /
• v.21 no.8
• /
• pp.735-743
• /
• 2002

In this paper, we propose three new text-independent speaker identification methods. At first, to exclude the frames not having enough features of speaker's vocal from calculation of the maximum likelihood, we propose the FS(Frame Selection) method. This approach selects the important frames by evaluating the difference between the biggest likelihood and the second in each frame, and uses only the frames in calculating the score of likelihood. Our secondly proposed, called the Hybrid, is a combined version of the FS and WMR(Weighting Model Rank). This method determines the claimed speaker using exponential function weights, instead of likelihood itself, only on the selected frames obtained from the FS method. The last proposed, called MWMR (Modified WMR), considers both original likelihood itself and its relative position, when the claimed speaker is determined. It is different from the WMR that take into account only the relative position of likelihood. Through the experiments of the speaker identification, we show that the all the proposed have higher identification rates than the ML. In addition, the Hybrid and MWMR have higher identification rate about 2% and about 3% than WMR, respectively.

• Journal of Broadcast Engineering
• /
• v.7 no.2
• /
• pp.181-191
• /
• 2002

Video based surveillance systems based on an active camera require a fast algorithm for real time detection and tracking of local motion in the presence of global motion. This paper presents a new fast and efficient motion detection and tracking algorithm using the displaced frame difference (DFD). In the Proposed algorithm, first, a Previous frame is adaptively selected according to the magnitude of object motion, and the global motion is estimated by using only a few confident matching blocks for a fast and accurate result. Then, a DFD is obtained between the current frame and the selected previous frame displaced by the global motion. Finally, a moving object is extracted from the noisy DFD by utilizing the correlation between the DFD and current frame. We implement this algorithm into an active camera system including a pan-tilt unit and a standard PC equipped with an AMD 800MHz processor. The system can perform the exhaustive search for a search range of 120, and achieve the processing speed of about 50 frames/sec for video sequences of 320$\times$240. Thereby, it provides satisfactory tracking results.

• Korean Journal of Applied Biomechanics
• /
• v.22 no.3
• /
• pp.373-378
• /
• 2012

The purpose of this study was to develop an electric riding machine for cycle fitting to control riding posture easily, to measure frame size quantitatively, and to overcome disadvantages of the traditional systems. The electric riding machine consisted of actuator, load controller, and display & control unit. The actuator unit by BLDC(BrushLess Direct Current) motor drives the saddle height up and down, the crank forward and backward, the handlebar up and down, and the handlebar forward and backward. The load controller unit controls loads by Eddy current controller with electromagnet and aluminum circular plate. The display & control unit consisted of frame size controller and display panel which shows top tube length(485~663mm), head tube length(85~243mm), seat tube length(481~671mm), and seat tube angle($62.7{\sim}76.4^{\circ}$). The range of frame size control for developed electric riding machine did not have difference compared to traditional commercial systems, but quantitative and precise control with 0.1 mm length and $0.1^{\circ}$ angle was possible through digital measurement. Unlike traditional commercial systems, frame size control was possible during riding through motor driven method, thus fitting duration decreased. It is necessary for further improvement to have feedback from users. It is believed that developed electric riding machine can help to develop domestic fitting system.

• Journal of Korean Society of Steel Construction
• /
• v.13 no.5
• /
• pp.535-545
• /
• 2001

A refined method of analysis which is called the Advanced Analysis has been introduced This method is to consider the intial member imperfection residual stress and second-order effects so as to estimate the overall behavior of steel frame accurately Based on the refined plastic hinge method that is more suitable and practical in design practice. the program RPH-2DF is coded using the log model which represents the moment-rotation relationship of connection. The validity of this program is examined by frame test data. Finally to investigate the difference between behaviors of rigid and semi-rigid frame. the 10-story frame analysis results designed by MIDAS-GEN v4.2.2 are compared with the results by RPH-2DF.

• Journal of KIISE:Computer Systems and Theory
• /
• v.33 no.8
• /
• pp.536-546
• /
• 2006

Painterly animation is a method that expresses painterly images with a hand-painted appearance from a video, and the most crucial element for it is the temporal coherence of brush strokes between frames. A motion map is proposed in this paper as a solution to the issue of maintaining the temporal coherence in the brush strokes between the frames. A motion map is the region that frame-to-frame motions have occurred. Namely, this map refers to the region frame-to-frame edges move by the motion information with the motion occurred edges as a starting point. In this paper, we employ the optical flow method and block-based method to estimate the motion information. The method that yielded the biggest PSNR using the motion information (the directions and magnitudes) acquired by various methods of motion estimation has been chosen as the final motion information to form a motion map. The created motion map determine the part of the frame that should be re-painted. In order to express painterly images with a hand- painted appearance and maintain the temporal coherence of brush strokes, the motion information was applied to only the strong edges that determine the directions of the brush strokes. Also, this paper seek to reduce the flickering phenomenon between the frames by using the multiple exposure method and the difference map created by the difference between images of the source and the canvas. Maintenance of the coherence in the direction of the brush strokes was also attempted by a local gradient interpolation to maintain the structural coherence.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.14 no.1
• /
• pp.46-53
• /
• 2010

Purpose: The static image of nuclear medicine study should be acquired without a motion, however, it is difficult to acquire static image without movement for the serious patients, advanced aged patients. These movements cause decreases in reliability for quantitative and qualitative analysis, therefore re-examination was inevitable in the some cases. Consequently, in order to improve the problem of motion artifacts, the authors substituted the dynamic acquisition technique for the static acquisition, using motion correction. Materials and Methods: A capillary tube and IEC body phantom were used. First, the static image was acquired for 60 seconds while the dynamic images were acquired with a protocol, 2 sec/frame${\times}$30 frames, under the same parameter and the frames were summed up into one image afterwards. Also, minimal motion and excessive motion were applied during the another dynamic acquisition and the coordinate correction was applied towards X and Y axis on the frames where the motion artifact occurred. But the severe blurred images were deleted. Finally, the resolution and counts were compared between the static image and the summed dynamic images which before and after applying motion correction, and the signal of frequency was analysed after frequency spatial domain was transformed into 2D FFT. Supplementary examination, the blind test was performed by the nuclear medicine department staff. Results: First, the resolution in the static image and summed dynamic image without motion were 8.32 mm, 8.37 mm on X-axis and 8.30 mm, 8.42 mm on Y-axis, respectively. The counts were 484 kcounts, 485 kcounts each, so there was nearly no difference. Secondly, the resolution in the image with minimal motion applying motion correction was 8.66 mm on X-axis, 8.85 mm on Y-axis and had 469 kcounts while the image without motion correction was 21.81 mm, 24.02 mm and 469 kcounts in order. So, this shows the image with minimal motion applying motion correction has similar resolution with the static image. Lastly, the resolution in the images with excessive motion applying motion correction were 9.09 mm on X-axis, 8.83 mm on Y-axis and had 469 kcounts while the image without motion correction was 47.35 mm, 40.46 mm and 255 kcounts in order. Although there was difference in counts because of deletion of blurred frames, we could get similar resolution. And when the image was transformed into frequency, the high frequency was decreased by the movement. However, the frequency was improved again after motion correction. In the blind test, there was no difference between the image applying motion correction and the static image without motion. Conclusion: There was no significant difference between the static image and the summed dynamic image. This technique can be applied to patients who may have difficulty remaining still during the imaging process, so that the quality of image can be improved as well as the reliance for analysis of quantity. Moreover, the re-examination rate will be considerably decreased. However, there is a limit of motion correction, more time will be required to successfully image the patients applying motion correction. Also, the decrease of total counts due to deletion of the severe blurred images should be calculated and the proper number of frames should be acquired.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.1
• /
• pp.1-11
• /
• 2017

A lot of the energy are consumed on heating and cooling in buildings. The buildings need to minimize the heating and cooling loads for $CO_2$ emissions and energy consumption reduction. In recently, also demand of detached houses were increase while the residential culture was changed. The structure of the domestic detached houses can be divided into masonry, concrete, wood frame houses. Therefore, in this study, the heating and cooling load and energy demand were analyzed on the equal area detached house consisting of three structural methods (Masonry, Concrete, Wood frame). Layer of wall, roof, and floor were composited by structure. Thermal transmittance (U-value) of each layer was using the PHPP calculation for considering stud, such as the wood frame wall. In addition, the case of without considering for studs in wood frame wall (Non-studs) was analyzed in order to compare the difference between studs or not. Analysis was performed using self-developed heating and cooling load calculation program (CHLC) based excel and ECO2. The results of cooling and heating load and energy demand showed the highest values in the wood frame structure, and the concrete structure were confirmed to maintain a high value secondly. Two structure were determined to be disadvantageous on the energy consumption. Consequently, the masonry structure have an advantage over the other structure under the identical conditions. It was determined that if the except for thermal bridges due to the studs in the wood frame structure, it can be reduced the energy consumption.

• Structural Engineering and Mechanics
• /
• v.63 no.3
• /
• pp.347-359
• /
• 2017

Blast resistant gates are required to be lightweight and able to mitigate extreme loading effect. This may be achieved through innovative design of a gate and its supporting frame. The first is well covered in literature while the latter is often overlooked. The design of supporting frame depends mainly on the boundary conditions and corresponding reaction forces. The later states the novelty and the aim of this paper, namely, the analysis of reaction forces in supporting structure of rectangular steel gates subjected to "far-field explosions". Flat steel plate was used as simplified gate structure, since the focus was on reaction forces rather than behaviour of gate itself. The analyses include both static and dynamic cases using analytical and numerical methods to emphasize the difference between both approaches, and provide some practical hints for engineers. The comprehensive study of reaction forces presented here, cover four different boundary conditions and three length to width ratios. Moreover, the effect of explosive charge and stand-off distance on reaction forces was also covered. The analyses presented can be used for a future design of a possible "blast absorbing supporting frame" which will increase the absorbing properties of the gate. This in return, may lead to lighter and more operational blast resistant gates.

• Transactions of Materials Processing
• /
• v.7 no.3
• /
• pp.260-273
• /
• 1998

A new blank design method is proposed to predict the optimum initial blank shape in the sheet metal forming process. The rollback method for blank shape design takes the difference between final deformed shaped and target contour shape into account. Based on the method a computer program composed of blank design module FE-analysis program and mesh generation module is developed. The rollback method is applied to square cup drawing process with the flange of unifiorm size around its periphery to confirm its validity. The optimum initial blank shape is obtained from an arbitrary square blank after three modification. Good agreements are recognized between the numerical results and the published results for initial blank shape and thickness strain distribution. The optimum blank shape for two parts of automobile sub-frame is designed, The thickness distribution and the level of punch load is improved. Also the method is applied to design the weld line in the tailor-welded blank. It is concluded that the rollback method is an effective and convenient method for an optimum blank shape design.