• Journal of the Korean Ceramic Society
• /
• v.36 no.1
• /
• pp.7-14
• /
• 1999

TiZrB2 solid solution was synthesized using fine powders of Ti, Zr and B by SHS microwave process. The characterization of the synthesized powder and sintered bodies ws investigated. The combustion temperature and rate were increased with increasing the mole ratio of Zr in temperature profile, and showed the maximum combustion temperature and velocity values of 285$0^{\circ}C$ and 14.6mm/sec in Ti0.2Zr0.8B2 composition. Phase separation has been occured into a composite with TiB2 and ZrB2 phases from TiZrB2 solid solution, which was hot pressed sintering at 30 MPa for an hour at 190$0^{\circ}C$. At the composition of Ti0.8Zr0.2B2 the best properties has been obtained in relative density, bending strength, fracture toughness and hardness, with 99%, 680 MPa, 7.3MPa.m1/2 and 2750 Kg/$\textrm{mm}^2$ respectively.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.48 no.5
• /
• pp.292-296
• /
• 2022

Objectives: During Le Fort I osteotomy, the separation of the pterygomaxillary junction (PMJ) is a difficult procedure for most surgeons because it is invisible. In this process, damage to the posterior structures constituting the sinus or those adjacent to it, including the maxillary sinus posterior wall and pterygoid plate, may occur. We would like to investigate the effects of this on the inside of the maxillary sinus after surgery and whether there are complications. Materials and Methods: One-hundred patients who underwent Le Fort I osteotomy from 2013 to 2020 using cone-beam computed tomography images were classified into two groups (clean-cut type and fractured type) according to the PMJ cutting pattern. In addition, the mucosal thickness in the maxillary sinus was divided into preoperative, postoperative three months, one year, and the change over the course of surgery was evaluated retrospectively. Results: Of the total 100 cases, the clean-cut type numbered 28 cases and the fractured type totaled 72 cases. Among the fracture types, part of the sinus wall and the pterygoid plate were broken in 69 cases, and the maxillary sinus posterior wall was detached in three cases. There was no statistically significant difference in sinus mucosal thickening between the clean-cut type and fractured type of the PMJ, three months and one year after surgery between the two groups. However, there was a significant difference in sinus mucosal thickness at postoperative one year in the case where a partial detachment of the maxillary sinus posterior wall occurred compared to not. Conclusion: Even if there is some damage to the structures behind the PMJ, it may not be reasonable to spend some time on the PMJ separation process considering the overall postoperative complications, if there is no significant difference inside the sinus, or increased probability of postoperative complications.

• Journal of Trauma and Injury
• /
• v.26 no.3
• /
• pp.170-174
• /
• 2013

Purpose: A flail chest is one of most challenging problems for trauma surgeons. It is usually accompanied by significant underlying pulmonary parenchymal injuries and mayled to a life-threatening thoracic injury. In this study, we evaluated the treatment result for a flail chest to determine the effect of trauma localization on morbidity and mortality. Methods: Between 2004 and 2011, 46 patients(29 males/17 females) were treated for a flail chest. The patients were divided into two group based on the location of the trauma in the chest wall; Group I contained patients with an anterior flail chest due to a bilateral costochondral separation (n=27) and Group II contained patients with a single-side posterolateral flail chest due to a segmental rib fracture (n=19). The location of the trauma in the chest wall, other injuries, mechanical ventilation support, prognosis and ISS (injury severity score) were retrospectively examined in the two groups. Results: Mechanical ventilation support was given in 38 patients(82.6%), and 7 of these 38 patients required a subsequent tracheostomy. The mean ISS for all 46 patients was $19.08{\pm}10.57$. Between the two groups, there was a significant difference in mean ventilator time (p<0.048), but no significant difference in either trauma-related morbidity (p=0.369) or mortality (p=0.189). Conclusion: An anterior flail chest frequently affects the two underlying lung parenchyma and can cause a bilateral lung contusion, a hemopneumothorax and lung hemorrhage. Thus, it needs longer ventilator care than a lateral flail chest does and is more frequently associated with pulmonary complications with poor outcome than a lateral flail chest is. In a severe trauma patient with a flail chest, especially an anterior flail chest, we must pay more attention to the pulmonary care strategy and the bronchial toilet.

• Journal of Welding and Joining
• /
• v.15 no.4
• /
• pp.109-115
• /
• 1997

Laser cladding is a technique for modification of metal surface. In this laser cladding experiment a metal powder feeding system was developed for more efficient laser cladding. This system can reduce processing time and be used simpler than the conventional method. The feeding of metal powder has given a rise to the process for sequential buildup of bulk rapidly solidified materials in the form of fine powder stream to the laser cladding process. The parameters of laser cladding have been investigated using this experimental equipment. Bronze on aluminum alloy and copper on aluminum alloy were experimented by using defocused beam, powder feeding system, and gas shielding. Good cladding was achieved in the range of beam travel speed of 2.25m/min. In the case of copper/aluminum and bronze/aluminum substrate, the absorption of laser beam was too high to produce low diluted clad. In the case of copper/1050 aluminum, the optimal laser cladding condition was of laser power of 2.8kW, powder feed rate of 0.31g/s and beam travel speed of 2.25m/min. In the case of bronze/aluminum the optimal condition is of laser power of 2.5kW, powder feed rate of 0.31g/s, and beam travel speed of 2.36m/min.

• Journal of the Korean Society of Safety
• /
• v.25 no.3
• /
• pp.71-77
• /
• 2010

This paper presents the results of a study on flexural capacity of large size RC slabs strengthened with carbon fiber reinforced polymer(CFRP) plates. A total of 5 specimens of 6.0m length were tested in four point bending after strengthening them with externally bonded CFRP plates. The CFRP plates were bonded without prestress and with two prestress levels, 0.4% and 0.6% of CFRP plate strain. Test variables included the type of strengthening, prestressing level, and the effects according to each test variables are analysed. The experimental results show that proposed methods can increase significantly the flexural capacity such as strength, stiffness of the beam and the increase ranged between 36.2% and 63.2% of the load-carrying capacity of the control beams. The non-prestressed specimen failed by separation of the plate from the beam due to premature debonding while most of the prestressed specimens failed by CFRP plate fracture. And the cracking loads and maximum loads were increased proportionally to the prestress level.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05c
• /
• pp.79-84
• /
• 1996

Small punch test was performed on CF8 duplex stainless steel aged at 370 and 400$^{\circ}C$ up to 5,000 h to evaluate the degree of the thermal aging embrittlement. At room temperature, the SP load-displacement curve was in a similar shape to those of ferritic steels and had a good reproducibility in spite of two-phase structure. The aging heat treatment resulted in a slight increase of the yield strength. As test temperature was lowered, the SP load showed a sudden drop followed by serrations before the SP specimen was fractured, resulting from the cracking of ferrite phase. The extent of thermal embrittlement was assessed in terms of the SP energy. Aging treatment at higher temperature led to a larger shift in the transition temperature and the corresponding change in the fracture mode. The main cause of the degradation was the embrittlement of ferrite phase. Additionally the phase boundary separation profoundly contributed to the degradation of the specimen aged at 400$^{\circ}C$.

• Advances in aircraft and spacecraft science
• /
• v.5 no.5
• /
• pp.595-613
• /
• 2018

The objective of our study is to analyze the behavior of bonded, riveted and hybrid (bonded / riveted) steel / steel assemblies by tensile tests and to show the advantage of a hybrid assembly over other processes. the finite element method with the ABAQUS numerical code was used to model the fracture behavior of the different assemblies. Cohesive zone models (CZM) have been adopted to model crack propagation in bonded joints using a bilinear tensile separation law implemented in the ABAQUS finite element code. The riveted assemblies were modeled with the XFEM damage method identified in this ABAQUS numerical code. Both CZM and XFEM methods are combined to model hybrid assemblies. The results are consistent with the experimental results and make it possible to guarantee the validity of the applied numerical model. The use of a hybrid assembly shows a high resistance compared to other conventional methods, where the number of rivets has been highlighted. The use of the hybrid assembly improves mechanical strength and increases service life compared to a single lap joint and a riveted joint.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.02a
• /
• pp.136-143
• /
• 2002

Warm draw die technique which is one of the new forming technologies to improve formability of sheet metal is applied to the cylindrical and square cup drawing of stainless-aluminum clad sheets. In experiments the temperature of die and blank holder is varied from room temperature to $180^{\circ}C$, while the punch is cooled by circulation of coolant to increase the fracture strength of workpiece on the punch comer area. Test materials chosen for experiments are STS304-A1050-STS304 clad sheets. Teflon film as a lubricant is used on both sides of a workpiece. The limit drawing ratio and relative drawing depth as well as quality of drawn cups(distribution of thickness)are investigated and validity of warm drawing process is also discussed. No separation between each laminated material after drawing occurred through inspection by microscope as well as application of penetrant remover and bond strength test. Therefore, warm forming technique was confirmed to give better results in deep drawing of stainless clad sheet metal.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.1
• /
• pp.181-192
• /
• 2007

The purpose of this study is to analyse and compare experimentally flexural behavior of RC beams strengthened with CFRP plates by different methods, and finally suggest the evaluation equations of flexural capacity of RC beams with the aim of application of prestressed CFRP strengthening. The experimental parameters are compressive strength, reinforcement ratio, prestressing level and strengthening methods. The non-prestressed specimens failed on account of separation of the plates from the beams due to premature de-bonding, while most of the prestressed specimens failed due to CFRP plate fracture. The evaluation equations of flexural capacity of RC beams is suggested and these equations have a good reliability in predicting flexural strength of RC beams.

• Geophysics and Geophysical Exploration
• /
• v.9 no.4
• /
• pp.255-260
• /
• 2006

Measurements in two adjacent (about 1.5 m separation) boreholes reveal that there is a significant degree of variations in the width and property (permeability) of shear zones in the granitic rock. A high frequency (>10 kHz) cross-well seismic tomography was conducted to characterize the features of permeability distribution at the shear zones in the inter-well region. At the shear zones, the correlation between the permeability at the well location and the velocity pattern shown in the cross-well velocity tomogram suggests that a high resolution velocity tomogram may provide useful information for the shear zone characteristics, such as permeability, fracture density, width, and length.