• 농업과학연구
• /
• 제41권4호
• /
• pp.473-480
• /
• 2014

Upon setting up a dedicated plastic greenhouse for tomato cultivation developed by the Rural Development Administration on the Gyehwa reclaimed land, this study was aimed at analyzing the problems can be occurred in the installation of plastic greenhouse on reclaimed lands as well as finding out solutions for improvement. A relatively cheaper wooden pile was used in the installation in order to supplement the soft ground conditions. Based on the results of ground investigation of the installation site, both the allowable bearing capacity and pulling resistance of the wooden pile with a diameter of 150 mm and a length of 10 m were computed and came out to be 30.645 kN. It was determined that the values were enough to withstand the maximum compressive force (17.206 kN) and the pullout force (20.435 kN) that are generally applied to the greenhouse footing. There are three problems aroused in the process of greenhouse installation, and the corresponding countermeasures are as follow. First, due to the slightly bent shape of the wooden pile, there were phenomenon such as deviation, torsion, and fracture when driving the pile. This could be prevented by the use of the backhoe (0.2) rotating tongs, which are holding the pile, to drive the pile while pushing to the direction of the driving and fixing it until 5 m below ground and applying a soft vibrating pressure until the first 2 m. Second, there exists a concrete independent footing between the column of the greenhouse and the wooden pile driven to the underground water level. Since it is difficult to accurately drive the pile on this independent footing, the problem of footing baseplate used to fix the column being off the independent footing was occurred. In order to handle with this matter, the diameter of the independent footing was changed from 200 mm to 300 mm. Last, after films were covered in the condition that the reinforcing frame and bracing are not installed, there was a phenomenon of columns being pushed away by the strong wind to the maximum of $11m{\cdot}s^{-1}$. It is encouraged to avoid constructions in winter, and the film covering jobs always to be done after the frame construction is completely over. The height of the independent footing was measured for 9 months after the completion of the greenhouse installation, and it was found to be within the margin of error meaning that there was no subsidence. The extent to the framework distortion and the value of inclinometers as well showed not much alteration. In other words, the wooden pile was designed to have a sufficient bearing capacity.

• 자원환경지질
• /
• 제47권5호
• /
• pp.489-496
• /
• 2014

본 연구는 충청남도 서산시 웅도 백운암에서 산출되는 석면에 대하여 박편관찰, X-선 회절분석, 주사전자현미경 관찰 등을 통해 석면의 광물학적 및 형태적 특성을 규명하고, 백운암의 광물학적 특성과의 상관관계를 통해 석면의 형성과정을 알아보고자 하였다. 연구 결과, 석면을 함유하고 있는 모암은 열수 변질 및 변성작용을 받았으며, 광물학으로는 주로 백운석과 소량의 방해석, 석영, 활석, 각섬석, 휘석 등으로 이루어진 백운암인 것으로 밝혀졌다. 모암 내 존재하는 석면은 섬유상-침상 입자형태를 가진 양기석-투각섬석계 석면이었으나, 변성정도에 따라 주상 및 침상형태를 가진 비석면형의 양기석-투각섬석도 존재하는 것이 확인되었다. 주상이나 침상 형태의 광물을 전자현미경으로 분석한 결과, 주상의 경우 벽개면을 따라 더 작은 침상 또는 주상의 입자로 쪼개지는 특성을 나타내어, 풍화과정에 의한 쪼개짐 현상에 의해 석면입자로 산출될 수 있음을 알 수 있었다. 특히 양기석-투각섬석 광물군에서 너비가 $1{\mu}m$ 이하인 휘어진 형태의 섬유상 석면 입자가 발견되었다. 기존 연구에서는 백운암 내에서 거의 발견되지 않았던 석면 입자가 웅도 백운암에서 검출되었고, 광물학적 분석 결과 석면광물은 Ca, Mg를 함유한 백운암질 석회암이 열수 변질을 받는 과정에서 형성되었으며, 주로 양기석-투각섬석 석면형태로 존재하는 것으로 밝혀졌다.

• Journal of the Korean Wood Science and Technology
• /
• 제44권1호
• /
• pp.40-47
• /
• 2016

구조용 집성재 라멘 접합부에 일반적으로 사용되는 접합철물을 대신하여 단판과 GFRP (Glass Fiber Reinforced Plastic)를 복합시킨 GFRP 보강적층판과 삽입 접착형 GFRP rod를 접합물로 사용하였다. 이들을 적용시킨 접합부에 대한 모멘트저항 성능평가 결과, 접합철물을 이용한 실험체(Type-1)와 비교하여 GFRP 보강적층판과 GFRP rod 핀을 사용한 실험체의 항복모멘트는 4% 낮게 측정되었으나 회전강성은 29% 높게 측정되었다. 또한 GFRP 보강적층판과 목재(Eucalyptus marginata)핀을 사용한 실험체는 Type-1 실험체와 비교하여 항복모멘트 11%, 회전강성 56% 높게 측정되며 가장 양호한 성능을 나타냈었다. 파괴형상과 완전탄소성 분석을 통해서도 핀에 의한 전단내력으로부터의 취성파괴가 아닌 연성거동을 나타내며, 접합내력이 상승하고 부재의 일체화가 이루어짐을 확인하였다. 반면, GFRP rod를 삽입 접착한 실험체는 접착 불량으로 측정이 불가하거나 접합성능이 매우 낮게 측정되었다.

• 대한치과보철학회지
• /
• 제34권2호
• /
• pp.385-402
• /
• 1996

The purpose of this study was to analyze how the stability of the implant prostheses and the loosening of the fastening screw was affected when the various types of Hex structure provided for the effect of anti-rotation of the single prostheses were given. Three dimensional finite element model was designed with which the implants with the external hex type of 0.75mm, 1.5mm and the implant with the internal hex type of 0.75mm, 1.5mm and the implant with the external hex type of $15^{\circ}$ tapered shape of 0.75mm were supposed to completely osseointegrate to the mandible. After fininshing the finite element model, the preload of 10N at the fastening screw was applied and then the vertical and $30^{\circ}$ lateral load of 200N was applied respectively at the cusp tips of the prostheses. The following results were obtained : 1. In case of displacement, the amount of displacement was increased at the internal hex type(model C, D) than at the external hex type(model A, B, E) when the vertical and lateral load was applied. 2. Less equivalent stress was represented at the model B with increased external hex height than at the model A when the vertical and lateral load was applied. 3. Much stress was represented at the model E with increased hex angle than at the model A in case of the stress happened to the implant body and the fastening screw when the vertical and lateral load was applied. 4. Much equivalent stress was represented at the model D with deepened internal hex height than at the model C when vertical and lateral load was applied. 5. The least stress was taken at the model B and the most stress was taken at the model D in case of the stress happened to the implant when the vertical and lateral load was applied. 6. The least stress was taken at the model C at the vertical load. And the least stress was taken at the model B at lateral load in case of the stress happened to the fastening screw. As a results of this study, the good lateral stability of prostheses and less stress of the component of implant was taken when the external hex height was increased, and the risk of neck fracture of implant and fastening screw was increased when the internal hex height was deepned because of long screw neck portion and thin implant neck portion.

• Restorative Dentistry and Endodontics
• /
• 제24권1호
• /
• pp.88-99
• /
• 1999

The purpose of this study was to investigate the physical properties of experimental composite resins made with the spherical and crushed fillers. The 14 experimental composite resins containing 0, 5, 10, 15, 20 and 25%(w/w) in spherical filler group and 0, 10, 20, 30, 40, 50, 60 and 70%(w/w) in crushed filler group, incorporated in a Bis-GMA matrix (Aldrich Co., USA), were made with 1% ${\gamma}$-methoxy silane treated fillers. The polymer matrix was made by dissolving 0.7%(w/w) of benzoyl peroxide(Janssen Chemical Co. Japan) in methacrylate monomer, whereupon 0.7%(v/v) N,N-dimethyl-p-toluidine(Tokyo Kasei Co. Japan) was added to the monomer. The weight percentage of each specific particle size distribution could be determined from a knowledge of the specific gravity, the weight(w/w), and corresponding volume %(v/v) of the filler sample in resin monomer. In crushed silica group and spherical silica group, the diametral tensile strengths and compressive strengths were measured with Instron Testing Machine(No.4467), and analyzed in 14 experimental composite resins made by filler fractions. The shear bond strength of 14 experimental composite resins to bovine enamel was measured with universal testing machine(Instron No.4467). The fracture surfaces were sputter-coated with a gold film and investigated by SEM. The results were as follows; 1. The diametral tensile strength was tendency to increase in crushed silica group, but not in spherical silica group. The highest diametral tensile strength was found in 20% filler fractions of two groups. 2. The compressive strength was higher in 15%(w/w) and 20%(w/w) in spherical silica group than in crushed silica group, but not in spherical silica group. 3. The significant correlation was noticed in increase in shear bond strength in crushed silica group, but not in spherical silica group. 4. The significantly highest shear bond strength was noticed in 50% filler concentration in crushed silica group, and in 15% filler concentration in spherical silica group, it was not significant in relation. 5. In crushed silica group, cut surface of resin matrix and the interface between resin and filler is obvious. In spherical silica group, fractures that occurred through the filler particles were round in shape.

• 비파괴검사학회지
• /
• 제31권5호
• /
• pp.459-465
• /
• 2011

대퇴골 근위부의 기하학적 형상은 대퇴골 경부 골절과 중요한 상관관계를 가지고 있는 것으로 보고되고 있다. 기존의 연구에서는 인장실험법과 유한요소해석법을 이용하여 상관관계를 분석해왔다. 그러나 이 방법들은 인체의 미리 정의된 대퇴골 형상을 변경할 수 없고, 다수의 시험편들을 확보하기 어렵기 때문에 다양한 시험편과 모델을 적용할 수 없다는 한계가 있다. 따라서 본 연구에서는 대퇴골 골절 해석에 폭넓게 사용할 수 있도록 매개변수로 기하학적 형상 변형이 가능한 대퇴골 모델을 이용하여 대퇴골 골절과 형상 매개변수의 관계를 분석하였다. 이 관계를 분석하기 위하여 4가지 주요 매개변수(대퇴골두 직경, 대퇴경부 직경, 대퇴경두간 길이, 대퇴경간각)를 이용하여 다양한 해석 모델을 생성하여 유한요소해석을 수행하였다. 이 후 대퇴골두에서의 반력(reaction force)과 경부에서의 응력 분포(stress distribution)를 분석함으로써 유한요 소해석을 수행하였고, 대퇴경부 직경이 대퇴골 경부 골절에 가장 큰 영향을 미치고 대퇴골두 직경이 가장 작은 영향을 미치는 결과가 나타났다.

• 지질공학
• /
• 제20권2호
• /
• pp.183-189
• /
• 2010

제3기 분지의 경계단층을 따라 발달하는 단층핵에서 단층비지 시료를 채취하여 현미경하에서 잔류입자들의 미구조 관찰과 잔류입자들을 이용한 프랙탈 차원 분석을 수행하였다. 타원형의 잔류입자들은 기질의 점토엽리(P엽리)에 평행 내지 아평행하게 형태선택배향을 이루는데 이는 풍부한 기질의 미세 입자 속에서 지속적인 단층 슬립 동안 회전에 의해 이루어진 것으로 생각된다. 잔류입자 크기 분포는 2.40-3.02 범위의 프랙탈 차원(D)을 갖는 멱 법칙을 따른다. 여기서 한 개의 시료를 제외한 모든 시료들은 Sammis et al. (1987)의 자기유사 파쇄 과정을 예측한 구속 분쇄 모델의 특정 차원 값 2.58보다 높은 값을 보이며 큰 단층 슬립과 다중단층작용을 지시한다. 아마도 비지대의 높은 차원 값은 구속 분쇄모델의 적용 범주를 지난 후부터는 파쇄 기구가 바뀌어 입자마모와 이에 부수적으로 조립입자의 선택적 파쇄가 일어남에 기인한 단층암의 비 자기유사 진화를 지시한다. 단층핵의 파쇄 진화를 통하여 후기의 입자마모 동안에 입자 파쇄가 부수적으로 일어날 수 있는 것과 마찬가지로 조기의 대량 파쇄 동안에도 부분적으로 입자마모가 수반될 수 있을 것으로 생각된다.

• Journal of Nutrition and Health
• /
• 제31권9호
• /
• pp.1446-1456
• /
• 1998

Bones are important parts in sustaining the shape of the body, but they are also metabolic organs which undergo bone remodeling by constant bone resorption and formation. Osteoporosis, the typical metabolic bone disease, is characterized by a reduction in bone mineral density (BMD). Women more than men are at risk fir osteoporosis-related fractures, especially in the lumbar spine, wrist, and hip region. Risk of fracture depends on one's BMD, which open determined by the peak bone mass value achieved at skeletal maturity and followed by subsequent age-and menopause-related bone loss. Genetic and environmental factors are known to play a key role in bone metabolism and diet is considered as one of the important environmental factors. The purpose of the present study was to assess the status of BMD and bone mineral content(BMC) to clarify the relationships between dietary intakes and the risk of osteoporosis in adult women in Taegu. Subjects were 130 healthy females in between 20 and 69 years of age. BMD and BMC of the lumbar spine(venebrae L2-4) of the subjects were measured by dual energy X-ray absorptiometry. The average age of the subjects was 47.4${\pm}$11.7 years old, the average weight was 57.2${\pm}$8.4kg, the average age of menarche was 16.6${\pm}$1.9 years old and the average age of menopause was 48.4${\pm}$5.3 years old. The nutrient intakes of the subjects measured by the convenient method were generally lower than the level of RDA. The result of nutrient intake assessed has shown that the average energy intake was 1701${\pm}$316kca1 which is 85.1% of the RDA and the average calcium intake was 485.4${\pm}$172.3mg which is 69.3% of the RDA. The intakes of protein, vitamin A, vitamin B$_1$, niacin were greater than the RDA, whereas the remaining nutrient intakes were lower than the RDA. The average BMD of the subjects was shown to be 1.06${\pm}$1.09g/$\textrm{cm}^2$. The highest BMD of 1.24${\pm}$0.14g/$\textrm{cm}^2$ was noticed in the subjects of 30s compared to 20s, 40s, 50s, 60s. The BMD values were compared by the relative body weight(R3W) of the menopause subjects, and it was found that the underweight group had significant lower BMB while the rest of the groups did not have any differences in BMD. The most strongly correlated nutrient with BMD among the menopause subjects appeared to be calcium. The women whose Ca intakes were higher than 500mg showed the significantly higher BMD than those with Ca intakes lower than 500mg. This study suggests that the most effective way to prevent osteoporosis and to reduce the incidences of fractures seems to be minimizing bone loss through the adequate intake of calcium as well as avoiding underweight, especially in menopausal women. (Korean J Nutrition 31(9) . 1446-1456, 1998)

• 한국광물학회지
• /
• 제32권4호
• /
• pp.259-271
• /
• 2019

채색 문화재 및 전통회화의 적색, 황색 안료로 사용되는 진사, 웅황, 그리고 자황의 광물학적 특성을 분석하고 촉진내후성 평가를 통한 안정성을 평가하였다. 진사는 시료명을 JB, JS로 하였고, 웅황과 자황은 각각 UH, JH로 하였다. 광물학적 특성 평가 결과 JB, JS는 cinnabar (HgS)로 주구성 광물이 확인되었고, 품위에 따른 화학성분에 차이를 보이지 않았다. UH와 JH는 각각 realgar (AsS), orpiment (As₂S₃)로 주구성 광물이 확인되었다. 편광현미경 관찰 결과 쪼개짐, 색상 등 편광학적 특성을 통해 모두 천연적으로 생성된 무기안료임을 알 수 있었다. 특히 진사의 경우 성분분석으로는 천연적으로 생성된 안료인지 인공안료인지 판별이 쉽지 않은데 편광현미경을 통해 천연안료가 가지는 입자특성 및 쪼개짐을 확인하였으며, 열적 반응 특성을 확인하였다. 열분석 결과 JH가 UH에 비해 유리전이 온도가 높고 안정한 것을 확인하였다. 촉진내후성 평가 결과 진사, 웅황 그리고 자황은 모두 광열화에 의한 색변화가 크게 나타나며, 진사는 최종적으로 흑색(blackening)되고 웅황과 자황은 밝은 노란색으로 변한다. Meta-cinnabar로 예상되는 JB가 cinnabar인 JS에 비해 흑화현상이 더 빨리 촉진되었으며, UH (realgar)는 광조사에 의해 arsenolite (As₂O₃)로 변하는 것을 확인하였다.

• Composites Research
• /
• 제29권6호
• /
• pp.408-413
• /
• 2016

흔히 사용되는 고분자는 다양한 형태로 제조되고 있다. 더 나아가, 나일론, 아라미드와 같은 연속적인 고분자 섬유가 최근에 제조되고 있다. 이번 실험에서 에폭시를 이용하여 고분자 섬유를 제조하였다. 비스페놀-A 타입의 에폭시가 사용되었고, 아민계 및 산 무수물계 경화제가 사용되었다. 에폭시 형상을 유지하기 위해 단계적 승온방식을 이용하여 에폭시 섬유를 경화했다. 계면접착력을 확인하기 위하여 두 섬유에 대한 상대적인 표면에너지를 수정된 정적 접촉각 방식으로 확인하였다. 인장실험을 통하여 기계적인 실험을 실시하였다. 인장실험 후에 파단형태가 경화제에 따라 달라지는 것을 확인하였다. 아민계 경화제를 사용한 에폭시 섬유의 경우 인장강도가 183 MPa로 70 MPa인 산 무수물계 경화제를 사용한 에폭시를 사용한 에폭시 섬유보다 더 좋은 것을 확인하였다.