• Computers and Concrete
• /
• 제13권4호
• /
• pp.569-585
• /
• 2014

In this paper, a four-layer road structure consisting of an edge transverse crack is simulated using three-dimensional finite element method in order to capture the influence of a single-axle wheel load on the crack propagation through the asphalt concrete layer. Different positions of the vehicular load relative to the cracked area are considered in the analyses. Linear elastic fracture mechanics (LEFM) is used for investigating the effect of the traffic load on the behavior of a crack propagating within the asphalt concrete. The results obtained show that the crack front experiences all three modes of deformation i.e., mode I, mode II and mode III, and the corresponding stress intensity factors are highly affected by the crack geometry and the vehicle position. The results also show that for many loading situations, the contribution of shear deformation (due to mode II and mode III loading) is considerable.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.1453-1454
• /
• 2011

• Restorative Dentistry and Endodontics
• /
• 제19권2호
• /
• pp.384-408
• /
• 1994

The purpose of this study was to evaluate the fracture resistance of tooth restored with gold inlay. A profound understanding of the isthmus width factor, which is one of the several parameters of cavity designs, would facilitate the appropriate cavity preparation in a specific clinical situation. In this study, the cavities for gold inlay were prepared in maxillary left first premolar. A three-dimensional model was designed using I-DEAS program. The model was composed of 2515- nodes and 2172 isoparametric brick elements. In the model isthmus width was varied into 1/4, 1/3 and 1/2 of intercuspal width respectively, and numeric values of the material properties of enamel, dentin and gold was set. Three types of load : concentrated load, divided load and distributed load was 500N. The empty cavities in the model were also examined using divided load and distributed load. The three - dimensional Finite Element Method was used to analysis the displacement and stress distribution. The results were as follows : 1. All of the experimental models which were filled with gold inlay revealed similar direction of displacement to that of the natural tooth model under the same load type. But in the models with empty cavities, as the isthmus width increased, the degree of displacement increased in the case of divided load type. 2. All experimental models which were filled with gold inlay showed stress concentration at load points, but in the models with empty cavities at divided load type, as isthmus width increased, stress was concentrated at the comer of the pulpal floor. 3. In the models with empty cavities at divided load type, tooth fracture was expected regardless of isthmus width, but all experimental models which were filled with gold inlay after cavity preparation were not susceptible to fracture. 4. In all experimental models which were filled with gold inlay after cavity preparation, displacement patterns were similar under both concentrated and divided load types. In the models with empty cavities, a divided load resulted in a bucco-lingual cuspal displacemenat in both sides, but a distributed load resulted in a lingual displacement of the tooth.

• 대한기계학회논문집A
• /
• 제26권6호
• /
• pp.1187-1193
• /
• 2002

Anodic bonding process has been quantitatively evaluated based on the Taguchi analysis of the interfacial fracture toughness, measured at the interface of anodically bonded silicon-glass bimorphs. A new test specimen with a pre-inserted blade has been devised for interfacial fracture toughness measurement. A set of 81 different anodic bonding conditions has been generated based on the three different conditions for four different process parameters of bonding load, bonding temperature, anodic voltage and voltage supply time. Taguchi method has been used to reduce the number of experiments required for the bonding strength evaluation, thus obtaining nine independent cases out of the 81 possible combinations. The interfacial fracture toughness has been measured for the nine cases in the range of 0.03∼6.12 J/㎡. Among the four process parameters, the bonding temperature causes the most dominant influence to the bonding strength with the influence factor of 67.7%. The influence factors of other process parameters, such as anodic voltage and voltage supply time, bonding load, are evaluated as 18%, 12% and 2.3%, respectively. The maximum bonding strength of 7.23 J/㎡ has been achieved at the bonding temperature of 460$\^{C}$ with the bonding load of 45gf/㎠, the applied voltage of 600v and the voltage supply time of 25minites.

• 대한조선학회논문집
• /
• 제61권1호
• /
• pp.44-50
• /
• 2024

In order to reasonably predict damage extents of naval ships under in-compartment explosion (INCEX) loads, two conditions should be fulfilled in terms of accurate INCEX load generation and fracture estimation. This paper seeks to predict damage extents of various naval ships by applying the CONWEP model to generate INCEX loads, combined with the Hosford-Coulomb (HC) and localized necking (LN) fracture model. This study selected a naval ship with a 2,000-ton displacement, using associated specifications collected from references. The CONWEP model that is embedded in a commercial finite element analysis software ABAQUS/Explicit was used for INCEX load generation. The combined HC-LN model was used to simulate fracture initiation and propagation. The permanent failures with some structural fractures occurred where at the locations closest to the explosion source points in case of the near field explosions, while, some significant fractures were observed in way of the interfaces between bulkheads and curtain plates under far field explosion. A large thickness difference would lead to those interface failures. It is expected that the findings of this study enhances the vulnerability design of naval ships, enabling more accurate predictions of damage extents under INCEX loads.

• 대한토목학회논문집
• /
• 제14권4호
• /
• pp.761-769
• /
• 1994

열차 바퀴의 접촉하중에 의해 레일이 받는 하중형식은 모드 I과 모드 II가 조합된 혼합모드 하중 상태로서 본 연구에서는 레일강의 피로파괴거동을 규명하기 위해 Richard가 개발한 혼합모드 파괴시험편 및 시험 지-그(Jig)를 이용하여 파괴시험을 실시하였으며 그 결과로부터 혼합모드에 대한 용력강도계수의 상관관계를 이용하여 균열성장경로를 평가하고 기제안된 다양한 파괴기준을 비교하였다. 그 결과, 레일강의 균열성장경로는 최대원주응력설과 변형에너지밀도설을 파괴기준은 주변형률설을 따름을 알 수 있었다.

• 한국세라믹학회지
• /
• 제41권9호
• /
• pp.690-695
• /
• 2004

본 연구에서는 무기(강, 아스베스트와 카본) 및 유기(폴리아크릴과 폴리아마이드) 섬유가 포트랜드 시멘트의 물성 보강에 미치는 영향을 조사하였다. 각 시편의 하중-변형 관계도로부터 굽힘강도, 탄성계수, 파괴에너지 및 파괴인성 값을 구하여 서로 비교하였다. 그리고 따로 충격에너지 실험도 수행하였으며 파괴에너지와 비교하였다. 휨강도 개선에는 무기(아스베스트) 섬유보강이 가장 효과적이었으며, 충격에너지의 보강섬유로는 유기(폴리아크릴) 섬유가 가장 좋았다. 한편 강 섬유는 휨 강도와 충격에너지 양자를 동시에 보강하는 데에 가장 적합했다. 또한 강 섬유는 모든 섬유 중에서 가장 높은 파괴에너지와 파괴인성 값을 나타내었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.262-267
• /
• 2004

The unloading compliance method is the most commonly used method to evaluate the fracture resistance characteristics of a material. In dynamic loading condition, the direct current potential drop(DCPD) method has been used because the unloading compliance method can not be applied due to the discontinuity of loading. However, even in the dynamic test using DCPD method, there is a problem that the voltage drops sharply on the initiation of crack. For the reason metioned above, the normalization method was suggested on ASTM E 1820 which is revised recently, as a new method to evaluate the dynamic fracture resistance characteristic. The nomalization method can be used to obtain a fracture resistance curve directly from a load-load line displacement. In this study, we obtained two fracture resistance curves from static test of welding part of nuclear piping both by unloading compliance and nomalization method. The two curves were almost same each other, so the adaptability of the nomalization method has been proved. We conducted a dynamic fracture resistance test for the same material. The fracture resistance curve from the dynamic test was obtained by normalization method and compared to that of the static test result.

• 한국자동차공학회논문집
• /
• 제6권2호
• /
• pp.80-91
• /
• 1998

In this paper, the estimation of dynamic interlaminar fracture toughness on fracture mode II in CFRP(carbon fiber reinforced plastics) laminates in made. Dynamic ENF(End Notched Flexure) apparatus used in this paper is manufactured by suing Split Hopkinson Pressure Bar. The static and impact load history in the CFRP specimen is measured by using manufactured dynamic ENF tester and 3-point bending test is carried out to find the load history. Also dynamic interlaminar fracture toughness can be found by using the J integral obrained from dynamic analysis in consideration of intertia-force effect.

• 대한기계학회논문집A
• /
• 제29권4호
• /
• pp.606-613
• /
• 2005

Effects of circumferentially local wall thinning on the fracture behavior of pipes were investigated by monotonic four-point bending. Local wall thinning was machined on the pipes in order to simulate erosion/corrosion metal loss. The configurations of the eroded area included an eroded ratio of d/t= 0.2, 0.5, 0.6, and 0.8, and an eroded length of ${\ell}\;=10mm,$ 25mm, and 120mm. Fracture type could be classified into ovalization, local buckling, and crack initiation depending on the eroded length and eroded ratio. Three-dimensional elasto-plastic analyses were also carried out using the finite element method, which is able to accurately simulate fracture behaviors excepting failure due to cracking. It was possible to predict the crack initiation point by estimating true fracture ductility under multi-axial stress conditions at the center of the thinned area.