• 전기의세계
• /
• v.14 no.2
• /
• pp.14-24
• /
• 1965

The characteristics of servo-multipliers and its accuracies are analyzed. From the analysis a low cost high accuracy four quadrant servo-multiplier with first derivative output feedback is built. The multiplier servomechanism has a second order system response with a damping ratio of 0.8 and computing bandwidth of 4 cycles per second, and its tracking accuracy at low speed of 0.5 volt per second is 0.9 per cent of maximum output voltage and static accuracy is better than 0.6 per cent. Method of testing this multiplier and the results are also described. The test on the characteristics of the multiplier shows that the results agree with theoretical values satisfactorily, and justifies the use of the servo-multiplier for slow type analog computers.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.992-994
• /
• 2004

In this paper, hybrid electromagnets using NdFeB permenant magnet are designed by 3-dimensional finite element analysis. Four hybrid magnets levitate the carrier of which total weight including control circuits and battery is 14[kg]. The nominal air gap length of the hybrid magnet is 3[mm]. The control circuit consists of DSP, 4-quadrant chopper, and gap sensor as feedback sensors. As a result, some experimental results for the magnetic levitation control by PI feedback control theory are shown.

• Proceedings of the KIEE Conference
• /
• 1993.07a
• /
• pp.202-204
• /
• 1993

Appropriate control of real and reactive power flowing in and out from system can lead to considerable benefits : network stabilization, load leveling, voltage regulation etc. This paper presents how to control real and reactive power flow between an flywheel energy storage system and a power three phase network. The system compensating real and reactive power consists of control system and cycloconverter operating in the four quadrant modes.

• The Bulletin of The Korean Astronomical Society
• /
• v.45 no.1
• /
• pp.67.3-68
• /
• 2020

A prime focus telescope, e.g., Schmidt telescope, has advantages especially for a wide field of view survey in astronomy. In this optical configuration, the camera is placed in front of the primary mirror. Since the installation of a typical filter wheel to the prime focus telescope causes serious obscuration of the incoming light, a customized filter device is required for high sensitivity images. In this poster, we present a new filter exchange mechanism, which can host four filters moving along quadrant directions. We plan to install this on the Celestron 36 cm Rowe-Ackermann Schmidt Astrograph (RASA 36) located at El Sause Observatory in Chile.

• Journal of Electrical Engineering and information Science
• /
• v.1 no.1
• /
• pp.51-57
• /
• 1996

An improved predictive current control technique for a zero current switched(ZCS) buck-boost series resonant inverter(SRI) is proposed to overcome the inherent disadvantages such as the uncontrollable large overshoot and the large current ripple. Using the proposed technique, four quadrant operations of the output voltage and current for an uninterrutible power supply(URS) application are guaranteed and the buck-boost operation can also be obtained without an additional bidirectional switch.

• The Journal of Engineering Geology
• /
• v.31 no.4
• /
• pp.507-522
• /
• 2021

Specific survey objectives often cannot be met using only one geophysical method, as each method's results are influenced by the specific physical properties of subsurface materials. In particular, areas susceptible to geological hazards require investigation using more than one method in order to reduce risks to life and property. Instead of analyzing the results from each method separately, this work develops a four-quadrant criterion for classifying areas of levees as safe or weak. The assessment is based on statistically determined thresholds of seismic velocity (P-wave velocity from seismic refraction and S-wave velocity from multichannel analysis of surface waves) and electrical resistivity. Thresholds are determined by subtracting the standard deviation from the mean during performance testing of this correlation technique applied to model data of four horizontal and inclined fracture zones. Compared with results from the crossplot of resistivity and P-wave velocity, crossplot analysis using resistivity and S-wave velocity data provides more reliable information on the soil type, ground stiffness, and lithological characteristics of the levee system. A loose and sandy zone (represented by low S-wave velocity and high resistivity) falling within the second quadrant is interpreted to be a weak zone. This interpretation is well supported by the N values from standard penetrating test for the central core.

• The korean journal of orthodontics
• /
• v.24 no.3 s.46
• /
• pp.709-719
• /
• 1994

The aim of this investigation was to identify which suing is more suitable for uprighting of the 30 degree inclined lower second molar in different situations. Between four different molar uprighting springs which were A, B, C type and T-loop spring, the author tested T-loop suing as a control material and the other springs were experimental group. Each spring was fabricated from .017' $\times$ .025' TMA wire and preactivated with 40 degree tip-back bend. Stabilizing unit included from the lower right central incisor to the lower right second premolar which were made by acrylic resin. The photoelastic overview of the lower right quadrant showed that stress concentrations were observed in its photoelastic model. The obtained results were as follows. 1. Higher concentration of compression can be seen clearly at the distal curvature than the mesial of the lower second molar when A type uprighting spring was applied, which can be used as a space regainer. 2. Higher level compression was presented at the mesial root apex area than the distal of the lower second molar in B type uprighting spring, which can be used as a space closer. 3. Areas of higher compression and tension were observed about the mesial and distal root of the lower second moalr than A and B type in C type uprighting spring, which can be used as a partial space regainer.

• The Korean Journal of Food And Nutrition
• /
• v.33 no.1
• /
• pp.111-115
• /
• 2020

The purpose of this study is an application of Lee's Menu Engineering (LME) method for menu analysis on the eight kinds of pizza selected from 17 kinds of pizza served by an Italian restaurant near by the Keimyung College University campus. The eliminated nine items were in the third quadrant or below the trend line. The LME method is more efficient than generally used methods such as the Miller, Kasavana & Smith, Uman, Pavesic and Merricks & Jones method. The LME method comprises reference lines and four quadrants created by x, y axes and its average values. The x and y axes comprise the sales ratio (MM%, percentage of the Menu Mix) and the weighted contribution margin (WCM%, percentage of the Weighted Contribution Margin) respectively. The obtained results are such that total sales increased by 1.59% from 58,747,200 won to 59,684,000 won, despite the decrease in sales volume. Total contribution margin also increased from 35,248,320 won to 35,810,400 won. The trend line also shows from y=0.9147x (R²=0.703) to y=0.9944x (R²=0.9893). These results indicate that the LME method is superior in practical applications.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.2
• /
• pp.130-136
• /
• 2015

This study describes the structure and operation modes of vertical stabilization (VS) converter for international thermonuclear experimental reactor (ITER) and proposes a protection method. ITER VS converter supplies voltage (${\pm}1000V$)/current (${\pm}22.5kA$) to superconducting magnets for plasma current vertical stabilization. A four-quadrant operation must be achieved without zero-current discontinuous section. The operation mode of the VS converter is separated in 12-pulse mode, 6-pulse mode and circulation current mode according to the magnitude of the load current. Protection measures, such as bypass and discharge, are proposed for abnormal conditions, such as over current, over voltage, short circuit, and voltage sag. VS converter output voltage is controlled to satisfy voltage response time within 20 msec. Bypass operation is completed within 60 msec and discharge operation is performed successfully. The feasibility of the proposed control algorithm and protection measure is verified by assembling a real controller and implementing a power system including the VS converter in RTDS for a hardware-in-loop (HIL) facility.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.3
• /
• pp.353-361
• /
• 2001

Recently the boundary element method has been developed swiftly. The boundary element method is an efficient and accurate means for analysis of two dimensional elastic crack problems. This paper is concerned with the evaluation and the prediction of the stress intensity factor(SIF) for the crack emanating from the circular hole using boundary element method-neural network. The SIF of the crack emanating from the hole was calculated by using boundary element method. Neural network is used to evaluate and to predict SIF from the results of boundary element method. The organized neural network system (structure of four processing element) was learned with the accuracy 99%. The learned neural network system could be evaluated and predicted with the accuracy of 83.3% and 71.4% (in cases of SIF and virtual SIF). Thus the proposed boundary element method-neural network is very useful to estimate the SIF.