• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.316-321
• /
• 2000

Die Casting is one of the forming methods to manufacture large number of products with short period time and clean surface by high forming pressure and temperature of cast alloy. Die design is composed of selection of cast alloy, design of die casting product, runner and gate design etc. In reality, however, die design of die casting has been performed by trial and error method, which cause economic and time loss. This paper describes a research work of developing computer-aided design of die casting product and die design. Approach to the CAD system has been written in AutoLISP on the AutoCAD with personal computer. In this study, die design system for gate of die casting process has been developed to present algorithm for automation of die design, especially runner-gate system. As forming process and die design system using 3-D geometry handling are integrated with technology of process planning, die design is possible to set. In addition, specific rules and equations for the runner-gate system have been presented to avoid too many trails and errors with expensive equipment. It is possible for engineers to make automatic and efficient die design of die casting and it will result in reduction of expense and time to be required. An example is applied to cap-shaped casting using proposed algorithm.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.252-257
• /
• 2000

An efficient method is developed for mold thermal cycle analysis in repeated forming process, which is well suited to the analysis in TV glass production. plunger, which is a mold to press-form the glass, undergoes temperature fluctuation during a cycle due to the repeated contact and separation from the glass, which attains a cyclic steady state in the end. If analyzed straightforwardly of this problem, it leads to more than 80 cycles to get reasonable solution, and it is yet hard to setup stopping creteria due to extremely slow convergence. An exponential fitting method is proposed to solve the problem, where an exponential function is found to best approximate temperature values of 3 consecutive cycles, and new cycle is restarted with the function value at infinite time. From numerical implementation, it is found that the method reduces the number of cycles dramatically to only $6{\sim}15$ cycles to reach accurate solution within $1^{\circ}$ error. A system for the analysis is contructed, in which the thermal analysis is performed by commercial software ANSYS, and the fitting of the result is done by IMSL library.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.11a
• /
• pp.71-78
• /
• 2004

Most of member parts have experienced severe springback problems because of their open shape Now it becomes imperative to develop an effective method, which can resolve these problems. However, there remain several obstacles to get accurate estimation of shape error. In analysis, we have to analyze the total process including forming, trimming and flanging. Furthermore, it is another challenge to compare the computed result with the real shape. In this study we developed an analysis program for the springback analysis. We could achive a big enhancement in computation time in springback analysis by using latest equation solving technique and could get a more robust solution conversence by contination method. We have approached this problem in two steps. In the first step, we analyzed forming stage to solve tearing and wrinkling problems. In the second step, we have analyzed full process and have done springback analysis with the same boundary condition as field measuring conditions. We have investigated the accuracy of springback analysis in terms of gap and flush used for insfection of real autobody panels. We found good and effective agreement with the observed results.

• Journal of Mechanical Science and Technology
• /
• v.14 no.1
• /
• pp.48-56
• /
• 2000

The bifurcation problem of thin walled structures in contact with rigid surfaces is formulated by adopting the multiple scales asymptotic technique. The general theory developed in this paper is very useful for the bifurcation analysis of waviness instabilities in the sheet metal forming. The formulation is presented in a full Lagrangian formulation. Through this general formulation, the bifurcation functional is derived within an error of O($(E^4)$) (E: shell's thickness parameter). This functional can be used in numerical solutions to sheet metal forming instability problem.

• Journal of Mechanical Science and Technology
• /
• v.17 no.3
• /
• pp.321-328
• /
• 2003

The elongation of contact length on the line of action is considered with particular reference for roll forming of gears, and for dynamic behavior of the tooth in meshing. However there is no paper that discuss the elongation of contact length in the load meshing of gears. Based on our investigation, the contact length on the line of action elongates more than the kinematically calculated value. In rolling, as the tool approaches the workpiece, the center distance of the gears decreases by a small amount. But, the elongation of contact length is sensitive. Therefore, the contact point on the line of action is difficult to be determined, which complicates the tooth analysis. In this study, the exact relation between the elongation of contact length and the tooth space over the recess or before the approach are revealed by experiments and kinematic theory. This analytical result applies not only for rolling, but also for the single flank meshing which is done under constant center distance.

• Journal of electromagnetic engineering and science
• /
• v.3 no.1
• /
• pp.62-66
• /
• 2003

Novel coupled line phase shifters and its equivalent phase delay line for compact broadband phased array antennas are proposed. These phase control circuits are designed to be less complex, small size and to use a less number of active devices. The phase shifter is able to control a 120$^{\circ}$ phase shift continuously, and the phase delay line for a reference phase has a fixed 60$^{\circ}$ shifted phase. Both have the low phase error of less than $\pm$3.5$^{\circ}$ and the low gain variations of less than 1 ㏈ within the 300 MHz bandwidth. These proposed circuits are adequate to form the efficient beam-forming networks with compactness, broadband, less complexity, and low cost.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39A no.9
• /
• pp.563-565
• /
• 2014

Beam forming techniques are used to increase the efficiency of using frequency. In this paper we design and implement Butler matrix to be used for ISM band. The implemented Butler matrix has the insertion loss of maximum 6.7dB and the maximum phase shift error of $-6.51^{\circ}{\sim}7.17^{\circ}$ over 2.4~2.485GHz.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.32B no.1
• /
• pp.110-119
• /
• 1995

The lateral resolution in an ultrasound imaging system is one of the most important factors for quality of the image and is determined by the beam focusing. For the better lateral resolution SDF(Sampled Delay Focusing) capable of digital focusing was proposed. The second-order sampling, one of band-width sampling methods, is suggested as being the best suitable for SDF because it allows total digital processing and is simple and economical. By proving that it introduces too much error, this article shows the second-order sampling is not appropriate for sampling of the wide-band signal generally used in ultrasound imaging systems. Also, this article suggests new sampling methods that maintain the advantages and reduce the unavoidable errors of the second-order sampling method. From computer simulation it is expected that the proposed methods reduce the errors of the second-order sampling method and can be used in real applications.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.180-183
• /
• 2006

The contraction rate is a very important element that dominate quality of product in plastic injection molding. To get wanted products, the contraction rate of used resin must be considered necessarily when designing plastic injection molds, and suitable deform conditions must be chosen with this. In this paper, important parts used in LED department were produced by injection mold using POM resin, and dimension error that happened by contraction rate of resin was corrected and reflected in die design and suitable deform conditions were decided.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.04a
• /
• pp.3-8
• /
• 2001

This study is an investigation for the ADS optimum design by using FEA. We write out program which express ADS perfectly and reduce the required time for correcting of model to the minimum in solution and manufacture result. We complete algorithm which can plan optimum forming of model by feedback error information in CAE. Then we correct model by feedback date obtaining in solution process, repeat course following stress solution again and do modeling rachet wheel for optimum forming. That is our aim. In rachet wheel, greatest equivalence stress originates in key groove corner and KS standard is proved the design for security.