• Economic and Environmental Geology
• /
• v.55 no.4
• /
• pp.377-388
• /
• 2022

Laboratory-scale experiments were performed to identify the As removal mechanism of the residual slag generated after the mineral carbonation process. The residual slags were manufactured from the steelmaking slag (blast oxygen furnace slag: BOF) through direct and indirect carbonation process. RDBOF (residual BOF after the direct carbonation) and RIBOF (residual BOF after the indirect carbonation) showed different physicochemical-structural characteristics compared with raw BOF such as chemical-mineralogical properties, the pH level of leachate and forming micropores on the surface of the slag. In batch experiment, 0.1 g of residual slag was added to 10 mL of As-solution (initial concentration: 203.6 mg/L) titrated at various pH levels. The RDBOF showed 99.3% of As removal efficiency at initial pH 1, while it sharply decreased with the increase of initial pH. As the initial pH of solution decreased, the dissolution of carbonate minerals covering the surface was accelerated, increasing the exposed area of Fe-oxide and promoting the adsorption of As-oxyanions on the RDBOF surface. Whereas, the As removal efficiency of RIBOF increased with the increase of initial pH levels, and it reached up to 70% at initial pH 10. Considering the PZC (point of zero charge) of the RIBOF (pH 4.5), it was hardly expected that the electrical adsorption of As-oxyanion on surface of the RIBOF at initial pH of 4-10. Nevertheless it was observed that As-oxyanion was linked to the Fe-oxide on the RIBOF surface by the cation bridge effect of divalent cations such as Ca²⁺, Mn²⁺, and Fe²⁺. The surface of RIBOF became stronger negatively charged, the cation bridge effect was more strictly enforced, and more As can be fixed on the RIBOF surface. However, the Ca-products start to precipitate on the surface at pH 10-11 or higher and they even prevent the surface adsorption of As-oxyanion by Fe-oxide. The TCLP test was performed to evaluate the stability of As fixed on the surface of the residual slag after the batch experiment. Results supported that RDBOF and RIBOF firmly fixed As over the wide pH levels, by considering their As desorption rate of less than 2%. From the results of this study, it was proved that both residual slags can be used as an eco-friendly and low-cost As remover with high As removal efficiency and high stability and they also overcome the pH increase in solution, which is the disadvantage of existing steelmaking slag as an As remover.

• Korean Journal of Veterinary Research
• /
• v.15 no.1
• /
• pp.57-67
• /
• 1975

The poxvirus group is considered to be a typical cytoplasmic inclusion forming virus. Every poxvirus has been reported to produce only one kind of inclusion in the infected tissues. A vague concept that inclusions of poxviruses are eosinophilic or acidophilic has prevailed. Although many papers and theories about the nature of the inclusion have been presented, most of them are not quite convincing on the point of the relations with virus multiplication, and an analysis of papers published showed that there seem to be many discrepancies in the descriptions of the nature of the poxvirus inclusions. Comparative studies on host-virus interaction with cowpox, orf, swinepox and fowlpox viruses which selected from each Group (I-IV) of poxviruses were performed from the morphological and virological standpoints. At first, in cowpox virus-FL cell system, as a comparative model, cytoplasmic inclusion, nucleic acid metabolism by autoradiography and detection of viral antigen by immunofluorescence were studied and obtained the results as follows: 1. The focus-like cytopathic effect (CPE) at early stage developed to entire culture at terminal stage of infection, and also the developing status of CPE was correlated to viral doses for inoculation. Two kinds of cytoplasmic inclusions which named A and B type were easily observed by Giemsa, hematoxylin-eosin (H & E) and May-Greenwald Giemsa (MGG) stainings in the infected cells. The B type inclusions were formed at early stage of infection and the A type inclusions were produced subsequently the B type formation. The B type which common type inclusion in poxviruses was a small compact or aggregate at early stage and developed to a large diffuse body at terminal stage of infection. On the other hand, the A type inclusion which depend upon the kind of virus was appeared as round and discrete shape, and its size and number was increased gradually during the culture period. It was characteristic to form distinct halos around the both types of inclusions in acid fixed, H & E stained preparations of infected cultures. The B type inclusion was always positive in Feulgen reaction and showed as DNA containing body but the A type inclusion was not. 2. In the relationship between inclusion and DNA metabolism of infected cells by the qualitative autoradiography using 3H-thymidine, the appearance of silver grains was coincided with B type inclusion but not with A type inclusion. This showed that the DNA synthesis was proceeded in all B type inclusions except those in the terminal stage with a diffuse form. This suggested that the B type inclusions are only sites of DNA synthesis and this was proceeded after the cell infection independently. The activity of DNA synthesis of the inclusions was nearly the same as that of the nucleic of normal cells and non-inclusion bearing cells. and non-inclusion bearing cells. Regardless of the size of the degree of DNA synthesis of the B type inclusion, inclusion bearing cells all showed remarkable suppression of nuclear DNA synthesis. 3. By the direct fluorescent antibody technique viral antigen in infected cells was detected. The B type inclusions have been proved to contain a great deal of viral antigen, whereas the basic substance of A type inclusion did not show antigenicity except the round edge. It was suggested that the round edge fluorescence might be caused by the glare of cytoplasmic viral antigen which pushed out and concentrated by the A type inclusion development. 4. Hemorrhagic red pock formations on chorioallantoic membrane of embryonated chicken egg had proved the characteristic of used viral strain. 5. By the above studies on the nature of two types of inclusions and the role they play in virus multiplication, it was concluded that the B type inclusion must be the site of the synthesis of viral DNA and protein as well as the site of the virus.

• Korean Chemical Engineering Research
• /
• v.53 no.5
• /
• pp.620-626
• /
• 2015

$Ho^{3+}$ doped $SrAl_2O_4$ upconversion phosphor powders were synthesized by spray pyrolysis, and the crystallographic properties and luminescence characteristics were examined by varying activator concentrations and heattreatment temperatures. The effect of organic additives on the crystal structure and luminescent properties was also investigated. $SrAl_2O_4:Ho^{3+}$ powders showed intensive green emission due to the $^5F_4/^5S_2{\rightarrow}^5I_8$ transition of $Ho^{3+}$. The optimal $Ho^{3+}$ concentration in order to achieve the highest luminescence was 0.1%. Over this concentration, emission intensities were largely diminished via a concentration quenching due to dipole-dipole interaction between activator ions. According to the dependence of emission intensity on the pumping power of a laser diode, it was clear that the upconversion of $SrAl_2O_4:Ho^{3+}$ occurred via the ground state absorption-excited state absorption processes involving two near-IR photons. Synthesized powders were monoclinic as a major phase, having some hexagonal phase. The increase of heat-treatment temperatures from $1000^{\circ}C$ to $1350^{\circ}C$ led to crystallinity enhancement of monoclinic phase, reducing hexagonal phase. The hexagonal phase, however, did not disappear even at $1350^{\circ}C$. When both citric acid (CA) and ethylene glycol (EG) were added to the spray solution, the resulting powders had pure monoclinic phase without forming hexagonal phase, and led to largely enhancement of crystallinity. Also, N,N-Dimethylformamide (DMF) addition to the spray solution containing both CA and EG made it possible to effectively reduce the surface area of $SrAl_2O_4:Ho^{3+}$ powders. Consequently, the $SrAl_2O_4:Ho^{3+}$ powders prepared by using the spray solution containing CA/EG/DMF mixture as the organic additives showed about 168% improved luminescence compared to the phosphor prepared without organic additives. It was concluded that both the increased crystallinity of high-purity monoclinic phase and the decrease of surface area were attributed to the large enhancement of upconversion luminescence.

• Korean Journal of Soil Science and Fertilizer
• /
• v.32 no.1
• /
• pp.76-83
• /
• 1999

Studies were conducted during 2 months from May of 1997 to evaluate the effects of pig manure compost(PMC) on soil microbial flora. To do so, a field experiment of Chinese cabbage(Brassica campestris L.) was conducted in a randomized block design on a sandy loam soil and microbial floral characteristics in soils were analyzed. Treatments to control included the application of PMC at (A) $8Mg\;ha^{-1}$CM-8), (B) $29Mg\;ha^{-1}$(CM-2,9), and (C) $57Mg\;ha^{-1}$(CM-57), and of chemical fertilizer(D) at $320N-80P_2O_5-200K_2O\;kg\;ha^{-1}$(NPK). In each treatment, the rhizosphere and non-rhizosphere soils were tested for the analysis of microbial populations. The populations of bacteria, actinomycetes, and fungi increased in soils with the applications of PMC and chemical fertilizer, but that of Bacillus sp. decreased. However, the population of fluorescent Pseudomonas sp. was reduced in NPK plots only. With increasing application rates of PMC, the number of colony forming units(cfu) of bacteria (Pseudomonas sp. and actinomycetes) and fungi increased. in all PMC-treated plots, the population density peaked at early growth stage for bacteria(including Bacillus sp.), at late growth for fluorscent Pseudomonas sp., and at harvest for fungi and actinomycetes. The rhizosphere effect was greatest for fluorscent Pseudomonas sp. As the application rates of PMC increased, Total N, organic matter, available phosphate, and exchangeable -K, -Ca, and -Mg increased compared to control, but soil pH was lowered. In NPK plots, EC was 3.4-fold and exchangeable K was 5-fold higher than control.

• Journal of the Korean Ceramic Society
• /
• v.39 no.1
• /
• pp.26-32
• /
• 2002

The effects of $Nd_2O_3$ addition to $Q{\cdot}f_{0}(GHz)$ ceramics with ${\varepsilon}_r$ of 126, $Q{\cdot}f_{0}(GHz)$ of 2240 and of $68\;ppm/^{\circ}C$ on their microwave properties were investigated. For the addition of 5 wt% $Nd_2O_3$, the dielectric constant (${\varepsilon}_r$) showed maximum value of 131, then decreased with the further addition of $Nd_2O_3$. $Q{\cdot}f_{0}(GHz)$ value was still increased to 3533 with 9 wt% $Nd_2O_3$ addition, it is influenced by densification of grain boundary. With more addition of $Nd_2O_3$ up to 18 wt%, the abnormal grain growth have influence on the decreasing of $Q{\cdot}f_{0}(GHz)$ value. But with the further addition of $Nd_2O_3$ over 25 wt%, the $Q{\cdot}f_{0}(GHz)$ value was again increased by the effect of the second phase ($Nd_2Ti_2O_7$) forming. The temperature coefficient of resonant frequency (${\tau}_f$) was decreased from $+\;68\;ppm/^{\circ}C$ with the addition of $Nd_2O_3$, reached $0\;ppm/^{\circ}C$ at 12 wt% addition, and became negative with the further addition of $Nd_2O_3$. The optimum microwave dielectric properties were obtained for $0.3CaTiO_3-0.7(Li_{1/2}Nd_{1/2})TiO_3$ with 9 wt% $Nd_2O_3$ sintered at $1425^{\circ}C$ for 3 hrs. The dielectric constant (${\varepsilon}_r$), the $Q{\cdot}f_{0}(GHz)$ value, and the temperature coefficient of resonant frequency (${\tau}_f$) were 108, 3533, and $+\;6\;ppm/^{\circ}C$, respectively.

• IMMUNE NETWORK
• /
• v.3 no.1
• /
• pp.47-52
• /
• 2003

Background: The megakaryopoiesis and platelet production is regulated by several hematopoietc factors such as thrombopoietin (TPO), interleukin-11 (IL-11) and interleukin- 3 (IL-3). IL-11 is a potent stimulator of megakaryopoiesis in vivo, and acts primarily as a megakaryocyte maturation factor in vitro and it can act synergistically with IL-3 and TPO. We performed this study to investigate the effects of recombinant human IL-11 (rhIL-11) with other hematopoietic factors on megakaryocyte colony formation in vitro. Methods: CD34+ cells were separated from umbilical cord blood and megakaryocyte colonies using MegaCult Assay Kit were cultured with rhIL-11, recombinant human IL-3 (rhIL-3), and recombinant human TPO (rhTPO) for 7 and 14 days. The number and percentage of CD34+ and CD41a+ cells were determined by flowcytometry. Results: The number of CD41a+ cells were $0.54{\pm}0.05{\times}10^4$ (rhIL-11 100 ng/ml), $5.32{\pm}0.23{\times}10^4$ (rhIL-3 100 ng/ml), and $8.76{\pm}0.15{\times}10^4$ (rhTPO 50 ng/ml) of total expanded cells during the culture of the purified CD34+ cells in liquid phase for 7 days. The number of CD41a+ cells were increased to $7.47{\pm}0.69{\times}10^4$ (rhIL-3+ rhIL-11), $11.92{\pm}0.19{\times}10^4$ (rhTPO+rhIL-11) of total expanded cells, respectively, during the culture of the purified CD34+ cells in liquid phase for 7 days in the presence of rhIL-11 (100 ng/ml). When the purified CD34+ cells were cultured in semisolid mediaincluding various concentration of rhIL-11, the megakaryocyte colonies were not formed. When the purified CD34+ cells were cultured with rhIL-11 and rhTPO or with rhIL-11 and rhIL-3, the number of megakaryocyte colonies were increased compared with rhTPO or rhIL-3 alone. Conclusion: These results indicate that IL-11 exerts a potent proliferative activity to colony forming unit-megakaryocyte from human umbilical cord blood, and it acts with other hematopoietic factors synergistically.

• Journal of the Korean Ceramic Society
• /
• v.40 no.5
• /
• pp.494-500
• /
• 2003

The effects of $Al_2$O$_3$ addition upon the sintering range of clay-EAF dust (the specified wastes produced from steel making process) system body which would be used as a constructing bricks were investigated. The slope of apparent density to sintering temperature decreased for Clay-dust body containing 5~15 wt% A1203 sintered at 1200-125$0^{\circ}C$, and the absorption(%) of specimen sintered above 125$0^{\circ}C$ decreased due to the formation of open pores produced by pore bloating. For the specimen without any $Al_2$O$_3$ addition sintered at 1275$^{\circ}C$, the major phase was cristobalite, the small amount of mullite (3Al$_2$O$_3$ 2SiO$_2$) formed and the hematite (Fe$_2$O$_3$) remained. In the Clay-dust system body containing $Al_2$O$_3$ 15 wt%, however, the cristobalite disappeared and the major phase was mullite. Also the part of $Al_2$O$_3$ reacted with hematite to form hercynite (FeAl$_2$O$_4$). From the these results, addition of $Al_2$O$_3$ to Clay-dust system body enlarges a sintering range; decreasing an apparent density and absorption slop to sintering temperature owing to consumption of liquid phase SiO$_2$ at higher temperature and gas-forming component Fe$_2$O$_3$ at reduced atmosphere which would decrease an amount of liquid formed and increase the viscosity of the liquid produced during the sintering process.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.33 no.2
• /
• pp.71-79
• /
• 2017

Purpose: Ni-Cr alloy does not contain Beryllium, causing the metal compound to form oxides in the furnace but by using Titanium as a chemical catalyst the forming of the oxides can be controlled, and by controlling the impurities formed on the metal surface, the possibility of the Ni-Cr alloy bond strength being increased can be analysed. Materials and Methods: Titanium was used as a chemical catalyst in the porcelain for the oxidation of beryllium-free metal (Ni-Cr) alloy. The T1 group, which does not use Titanium power as a chemical catalyst is a reference model for comparison. The T2 group and T3 group used 10 g and 20 g of Titanium power, respectively. They are fabricated to observe the shear bond strength and surface properties. There was no significance when One-way ANOVA analysis/Tukey Honestly Significant Difference Test was conducted for statistical analysis among groups (P > 0.05). Results: Results of measuring the three-point flexural bond strength of the Ni-Cr alloy and thickness of the oxide film. Experiment T3 using 20 g Titanium chemical catalyst: $39.22{\pm}3.41MPa$ and $6.66{\mu}m$, having the highest bond strength and thinness of oxide film. Experiment T2 using 10 g Titanium chemical catalyst: $34.65{\pm}1.39MPa$ and $13.22{\mu}m$. Experiment T1 using no Titanium chemical catalyst: $32.37{\pm}1.91MPa$ and $22.22{\mu}m$. Conclusion: The T2 and T3 experiments using Titanium chemical catalyst showed higher bond strength for the Ni-Cr alloy and lower thickness of oxide film than experiment T1, and the titanium catalyst being able to increase bond strength was observed.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.43 no.11
• /
• pp.1665-1673
• /
• 2014

The objective of this study was to compare the compositions and immuno-enhancing effects of 6-year-old red ginseng powder (RGP) with those of its fractions. RGP was subjected to extraction with 100% ethanol to obtain an ethanol fraction (E) and residue 1 (R1). Then, R1 was subjected to extraction with distilled water to obtain water fraction (W) and residue 2 (R2). Chemical compositions were as follows: 4.94% acidic polysaccharides and 1.56% ginsenosides (amounts of Rg1, Re, Rf, Rg2, Rb1, Rc, Rd, and Rg3) in RGP, 0.11% acidic polysaccharides and 6.99% ginsenosides in E, 4.93% acidic polysaccharides and 0.40% ginsenosides in R1, 0.50% acidic polysaccharides and 0.30% ginsenosides in R2, and 7.46% acidic polysaccharides and 0.61% ginsenosides in W. Immuno-enhancing effects of fractions from RGP were examined based on suppression of immune responses by cyclophosphamide. In the first fraction test, the antibody response to SRBCs increased significantly in the R1-treated group, but not the E-treated group. In the second fraction test, W showed higher immuno-enhancing effect than R1 and R2. W, which contained the highest amount of acidic polysaccharides, restored numbers of T and B cells, macrophages, as well as $CD4^+$ and $CD8^+$ T cells in the spleen suppressed by cyclophosphamide. These results suggest that acidic polysaccharides from red ginseng may be more effective than saponin in enhancing immune functions and reducing immunotoxicity of cyclophosphamide.

• Communications of Mathematical Education
• /
• v.25 no.2
• /
• pp.403-430
• /
• 2011

The purpose of the study was to investigate how the use of graphing calculators influence on forming students' mathematical concept of algebra, students' mathematical connection, and attitude toward mathematics. First, graphing calculators give instant feedback to students as they make students compare their written answers with the results, which helps students learn equations and linear inequalities for themselves. In respect of quadratic inequalities they help students to correct wrong concepts and understand fundamental concepts, and with regard to functions students can draw graphs more easily using graphing calculators, which means that the difficulty of drawing graphs can not be hindrance to student's learning functions. Moreover students could understand functions intuitively by using graphing calculators and explored math problems volunteerly. As a result, students were able to perceive faster the concepts of functions that they considered difficult and remain the concepts in their mind for a long time. Second, most of students could not think of connection among equations, equalities and functions. However, they could understand the connection among equations, equalities and functions more easily. Additionally students could focus on changing the real life into the algebraic expression by modeling without the fear of calculating, which made students relieve the burden of calculating and realize the usefulness of mathematics through the experience of solving the real-life problems. Third, we identified the change of six students' attitude through preliminary and an ex post facto attitude test. Five of six students came to have positive attitude toward mathematics, but only one student came to have negative attitude. However, all of the students showed positive attitude toward using graphing calculators in math class. That's because they could have more interest in mathematics by the strengthened and visualization of graphing calculators which helped them understand difficult algebraic concepts, which gave them a sense of achievement. Also, students could relieve the burden of calculating and have confidence. In a conclusion, using graphing calculators in algebra and function class has many advantages : formulating mathematics concepts, mathematical connection, and enhancing positive attitude toward mathematics. Therefore we need more research of the effect of using calculators, practical classroom materials, instruction models and assessment tools for graphing calculators. Lastly We need to make the classroom environment more adequate for using graphing calculators in math classes.