• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.4 s.117
• /
• pp.17-23
• /
• 2006

Paper has fibers and fines network structure and it is strongly affected by interface bond-ing between fibers. Paper structural properties can be determined depending on the inter-fiber bonding. Fines play an important role in Campbell and consolidation effect through wet pressing and drying operations. The fines are essential for the formation of bonds between fibers and for the improvement of strength properties of papers. Since the fines are components of the pulp, there are always two factors to be considered: the quality and quantity of the fines. The quality of fines might be a potential variable to give a more accurate picture of the papermaking potential of the pulp. The object of this study is to investigate the effect of different types of pulp fines on the properties of paper and to access the potential of fines for controlling the bulk of paper. Refined Sw-BKP, Hw-BKP and BCTMP fines were used to investigate the fines effect. Wet-web strength, breaking length, scattering coefficient, and hydrodynamic specific volume, and drying shrinkage were measured. According to the results, chemical and morphological compositions of fines do not strongly affect to wet-web forming by their similar Campbell effect, but strongly affect to drying operation which forms hydrogen bonding among fiber-fines-fiber matrixes. Paper bulk should be controlled by the extent of hydrogen bonding between fibers during drying operation.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.9 no.1
• /
• pp.1-7
• /
• 1976

1) The decrease in strength of netting twines at the knot may be regarded to be due mainly to the frictional force acting on the tip of the knot. The knot strength T may be given by $$T=\frac{T_0}{1+{\mu}\frac{s}{\rho}\varrho^{\mu\theta}$$ were $T_0$ is the tensile strength of unknotted netting twines, $\mu$ the coefficient of friction beween two netting twines forming a knot, s the contact length between the tip and the netting twine compressing it, $\rho$ the radius of curvature of the compressing, and $\theta$ the angle at which the compressing rubs with another one in the vicinity of the opposite tip. 2) Knots are arranged in order of strength as follows : the reef knot pulled lengthwise $\risingdotseq$ the trawler knot pulled breadtwise the reef knot pulled breadthwise.

• Journal of Plant Biology
• /
• v.13 no.2
• /
• pp.1-10
• /
• 1970

This experiment surveys ecological and morphological phase on Prasiola sp. in the mountain torrent of Chodang-ri, Keunduck-myon, Samchuck-gun, Kangwon-do, Korea from November 1968 through January 1970 and the results obtained were summarized as follows. 1. The temperature of the surface water was 12.4$\pm$2.3$^{\circ}C$, and pH was 7.25$\pm$0.2. 2. The external forms of thallus are very variable, but its basic form likely lanceolated and ovated. 3. The length of thallus is 0.6cm-8.8cm (3.6$\pm$1.72cm), and the width, 0.2cm-5.5cm(1.7$\pm$0.92cm). (The inside of the parentheses the average for 500 individuals). 4. It is observed that thallus at the time of formation of a monospore is a monostratum cell whose thickness is 21$\pm$3.2$\mu$. 5. Thickness of thallus at the transveres section at the time of heteroplanogametes formation is 29.9$\pm$2.2$\mu$, and that of the female gametes cell is 6.3$\pm$1.7$\times$6.3$\pm$0.8$\mu$, and that of the male gametes cell is 2.8$\pm$0.6$\times$28.1$\pm$1.1$\mu$. 6. As for growth, it begins with apical growth, followed by marginal growth. It seems to grow, through cell division when microsopical papillae are produced in growth line cell of marginal rigion thus by fusioning microscopical papillae. 7. The two kinds of thallus, one produced from a monospore and other from a planozygotes, are both haplonts and observed as n-3. 8. It seems that a thallus sprouts in April and increases its number through a asexual reproduction by a monospore and begins a sexual reproduction in November by forming gametes. 9. Female gametes are produced 16 from one thallus cell, whose structure shows 8 cells in the surface view and 4 layers in transverse section. Male gametes are produced 128 from one thallus cell, 16 cells surface, 8 layers in transverse section.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.9 no.2
• /
• pp.54-66
• /
• 2006

Korea Forest Service made the landslide hazard map for all mountainous districts over the country in May 2005. In this study, we selected landslide areas occurred in Jeonbuk from 02 August 2005 to 03 August 2005 as the study area. We extracted landslide areas using images taken by PKNU 3 System, which was developed by PE&RS Laboratory in Dept. of Satellite Information Sciences, Pukyong National University and verified the accuracy of landslide hazard map by overlaying landslide hazard areas extracted by PKNU 3 images. And we analyzed characteristics of an altitude, a gradient, an inclined direction, a flow length, a flow accumulation for landslide areas using mountainous terrain analysis and Stream Network analysis of ArvView 3.3. As a result of this study, it is necessary to adjust the unitage(%) by the class and to modify and improve the score table for prediction of landslide-susceptible area forming the foundation of making the landslide hazard maps.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.6
• /
• pp.38-47
• /
• 1989

A purely analytical model for HEMT's based on a two dimensional charge control simul-ation[4] is proposed. In this model proper treatment of diffusion effect of electron transport along a 2-DEG (two dimensional electron gas) channel is perfoemed. This diffusion effect is shown to effectively increase the bulk mibility and threshold voltage of the I-V curves compared to the existing models. The channel thickness and gate capacitance are expressed as functions of gate voltages covering subthreshold characteristics of HEMT's analytically. By introducing the finite channel opening and an effiective channel-length modulation, the solpe of the saturation region of the I-V curves ws modeled. The smooth transition of the I-V curves at linear-to-saturation regions of the I-V curves was possible using the continuous Troffimenkoff-type of field dependent mobility. Furthermore, a correction factor f was introduced to account for the finite transition section forming between a GCA and a saturated section. This factor removes large discrepancies in the saturation region of the I-V curve predicted by existing l-dimensional models.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.9
• /
• pp.806-813
• /
• 2015

In order to satisfy several conditions with respect to size, weight, and costs, automotive radars use an antenna consisting of a small number of receiving channels. If RELAX technique is applied to the automotive radars, angles of targets located in antenna beam can be estimated as well as the number of the targets. However, a small number of receiving channels in the antenna leads to inaccurate spectral estimation in angle domain, which in turn degrades performance of RELAX technique. Therefore, in this study, root-MUSIC technique coupled with MDL criterion is introduced to decide accurate angles of targets in antenna beam. In simulations, we show superior performance of proposed scheme using simulation results when three point targets are located in antenna beam.

• 한국해양학회지
• /
• v.16 no.1
• /
• pp.31-37
• /
• 1981

Saline water movements in relation to tidal condition and river discharge in the estuary of the Nakdong River are discussed on the basis of the observation data. The difference of salinity between the surface and the bottom layer was 1∼3 at spring tide forming a vertically homogeneous estuary, while at neap tide, it ranges up to 7∼15 indicating a sharp salt wedge. The maximum salinity appeared approximately at an hour after the high water, that is, three hours after the landward velocity maximum, while the salinity maximum at around an hour after the low water, that is, three hours after the seaward velocity maximum. The density current speed at a section located 10km landward from the river mouth was observed approximately to be 45cm sec$\^$-1/ at 8m layer.The relations between the salinity at Gupo and the river discharge at Jindong are estimated by means of the least square method. The maximum length of the salt wedge is calculated approximately to be 22km at neap tide and 16km at spring tide, which is in accordance with the observed data. The salinity influence area is deduced to be 45km at spring tide and 35km at neap tide. The diffusion coefficient of salinity was estimated approximately to be 1.5 10$\^$8/$\textrm{cm}^2$ sec$\^$-1/ at Samrak and 8 10$\^$5/$\textrm{cm}^2$ sec$\^$-1/ at Gupo at neap tide, while it was 1.4 10$\^$7/$\textrm{cm}^2$ sec$\^$-1/ at Dongwon at spring tide.

• Steel and Composite Structures
• /
• v.27 no.3
• /
• pp.337-353
• /
• 2018

In previous weak-axis moment connection tests, brittle fracture always initiated near the edge of the beam flange groove weld due to force flow towards the stiffer column flanges, which is the opposite pattern as strong-axis moment connections. As part of the China NSFC (51278061) study, this paper tested two full-scale novel weak-axis reduced beam section moment connections, including one exterior frame connection specimen SJ-1 under beam end monotonic loading and one interior frame joint specimen SJ-2 under column top cyclic loading. Test results showed that these two specimens were able to satisfy the demands of FEMA-267 (1995) or ANSI/AISC 341-10 (2010) without experiencing brittle fracture. A parametric analysis using the finite element software ABAQUS was carried out to better understand the cyclic performance of the novel weak-axis reduced beam section moment connections, and the influence of the distance between skin plate and reduced beam section, a, the length of the reduced beam section, b, and the cutting depth of the reduced beam section, c, on the cyclic performance was analyzed. It was found that increasing three parametric values reasonably is beneficial to forming beam plastic hinges, and increasing the parameter a is conducive to reducing stress concentration of beam flange groove welds while increasing the parameters b and c can only reduce the peak stress of beam flange groove welds. The rules recommended by FEMA350 (2000) are suitable for designing the proposed weak-axis RBS moment connection, and a proven calculation formulation is given to determine the thickness of skin plate, the key components in the proposed weak-axis connections. Based on the experimental and numerical results, a design procedure for the proposed weak-axis RBS moment connections was developed.

• Korean Journal of Optics and Photonics
• /
• v.10 no.6
• /
• pp.518-523
• /
• 1999

In thi, study, we made experiments to fonn a mesa shape by meltback method with various concentration of solutions and found that unsaturated (20%) InGaAsP (1.55 !-tm) solution at a growth temperature was the most suitable for the formation of a mesa ,hape on the wafer which has an InGaAsP active layer and an InP cap layer on an n-InP substrate. It was difficult to form a proper mesa shape for the fabrication of PBH-LDs only by the meltback method; therefore, we fabricated PBH-LDs by forming the mesa shape with the meltback method after wet etching and by growing a current-blocking layer successively. As the electrical and optical charaleri,tiecs of MQW-PBH-LDs fabricated by above methods, when the cavity length was $300{\mu}m$, the threshold current was about 10 mA, internal quantum efficiency 82%, internal loss $9.2cm^{-1}$, and characteristic temperature was 65 K at $25~45^{\circ}C$ and 42 K at $45~65^{\circ}C$. /TEX>.

• The Bulletin of The Korean Astronomical Society
• /
• v.43 no.1
• /
• pp.45.1-45.1
• /
• 2018

Formation of filaments and subsequent dense cores in ISM is one of the essential questions to address in star formation. To investigate this scenario in detail, we recently started a molecular line survey namely 'Filaments, the Universal Nursery of Stars (FUNS)' toward nearby filamentary clouds in Gould Belt using TRAO 14m single dish telescope equipped with a 16 multi-beam array. In the present work, we report the first look results of kinematics of a low mass star forming region L1478 of California molecular cloud. This region is found to be consisting of long filaments with a hub-filament structure. We performed On-The-Fly mapping observations covering ~1.1 square degree area of this region using C18O(1-0) as a low density tracer and 0.13 square degree area using N2H+(1-0) as a high density tracer, respectively. CS (2-1) and SO (32-21) were also used simultaneously to map ~290 square arcminute area of this region. We identified 10 filaments applying Dendrogram technique to C18O data-cube and 13 dense cores using FellWalker and N2H+ data set. Basic physical properties of filaments such as mass, length, width, velocity field, and velocity dispersion are derived. It is found that filaments in L~1478 are velocity coherent and supercritical. Especially the filaments which are highly supercritical are found to have dense cores detected in N2H+. Non-thermal velocity dispersions derived from C18O and N2H+ suggest that most of the dense cores are subsonic or transonic while the surrounding filaments are transonic or supersonic. We concluded that filaments in L~1478 are gravitationally unstable which might collapse to form dense cores and stars. We also suggest that formation mechanism can be different in individual filament depending on its morphology and environment.