• International Journal of Railway
• /
• 제2권2호
• /
• pp.43-49
• /
• 2009

Wear and rolling contact fatigue (RCF) defects are most important causes of rail damage, and often interaction competitive at present railway track. Head check is one of rolling contact fatigue (RCF) defects, and generally occurs in mild circular curves and transition curves that are set at both ends of sharp circular curves. Wear tends to limit the crack growth of head checks by removing the material from the RCF surface. In order to clarify the conditions of the occurrence and growth of head checks, the authors measured the interacting forces between wheels and rails and the angle of attack of wheelset, and carried out contact analyses using the actual profile data of wheels and rails. The effects of the lateral force, the contact geometry, and the wear rate at rail gauge comer on the formation of head checks were also analyzed by using the worn profiles of actual wheels and rails and the data obtained by a track inspection car. Some specific range of wear rate at the gauge comer was identified as having close relation with occurrence of head checks.

• Journal of the Korean Wood Science and Technology
• /
• 제29권3호
• /
• pp.21-26
• /
• 2001

Acquisition of precise information on drying characteristics of wood is indispensable for the improvement of drying schedules and wood quality. Recognition of the exact moisture content at which drying defects such as checks occur during drying with given drying conditions may be essential to reduce drying losses. In this study an image-processing system was combined with a laboratory-scale wood dry kiln for experiments and the surface of tree disk of black locust (Robinia pseudoacacia L.) was monitored to investigate the behavior of check formation over all the drying process. This system showed good potential for improving drying schedules and wood product quality.

• Journal of the Korean Wood Science and Technology
• /
• 제31권6호
• /
• pp.15-21
• /
• 2003

Image processing technique was adapted for exploring the more convenient ways to investigate the drying characteristics of wood. The acquisition of information about drying characteristics is indispensable for the development or improvement of dry-kiln schedules. A small internal fan type wood dry kiln was combined with image-processing and data-acquisition systems to monitor continuously the formation of checks and moisture reduction during drying. All the images and data were analyzed to improve or estimate the dry-kiln schedules and predict the drying time which would be required to dry green wood to 10% moisture content in internal fan type kiln. Samples of 20 mm- and 50 mm-thick Metasequoia glyptostrobodies, Paulownia coreana Uyeki, Pinus densiflora Sieb. Et Zucc., Platanus occidentalis L., Quercus acutissima and Robinia pseudo-acacia were used to verify the potentiality of this technique.

• Journal of the Korean Wood Science and Technology
• /
• 제36권6호
• /
• pp.59-68
• /
• 2008

본 연구에서는 엔드테이핑(End-taping) 처리가 두께가 20~75 mm이고, 직경이 120~470 mm인 백합나무 원반들의 고주파진공건조중 건조결함 예방 미치는 영향에 대하여 조사하였다. Inside end-taping (Inside-ET)과 Outside end-taping (Outside-ET)의 경우 두께 33 mm, 직경 270 mm 이하 원반에서 할렬의 예방효과가 우수하게 나타났다. 직경이 30 cm 이하이고, 두께 60 mm와 두께 75 mm의 원반에서도 전처리을 통하여 경계할렬을 예방할 수 있을 것으로 기대되었다. 경계할렬의 발생위치는 0.50~0.63 diameter 지점으로서 직경에 따라서 상이하였으며, 따라서 횡단면의 부분 엔드테이핑 처리의 경계선도 원반의 직경 따라 적정하게 선정할 필요가 있는 것으로 조사되었다. 중경재의 경우 0.3 diameter 지점이 경계할렬 예방을 위한 전처리의 경계점일 가능성이 높을 것으로 해석된다. 대경재의 경우 경계할렬과 V형 크랙에 의한 손상이 매우 심하였으며, 이는 방사방향으로의 함수율 분포변이가 극심한 백합나무 고유의 재질특성에 기인한 것으로 해석된다. 따라서 대경재의 경우 원반으로 활용하는 것은 적절하지 않는 것으로 생각된다.

• 한국가구학회지
• /
• 제11권1호
• /
• pp.61-68
• /
• 2000

This study was carried out to investigate the effect of grain and veneer thickness on drying rate, required energy consumption, and drying defects such as checking, end waving, and burning during a far-infrared radiation drying process of decorative veneers of hard maple and beech. Most of the veneer could be dried from green to in-use moisture content within 30 to 360 seconds. The drying rates were significantly affected by veneer thickness, but there was little difference between edge-and flat-sliced veneers. The formation of checking during drying test was none or very slight. The percentages of the veneers defected by checks were higher in the flat-sliced veneers than in the edge-sliced veneers. The maximum end wavinesses in the flat-sliced veneers were almost 1.6 to 3 times larger than that in the edge-sliced veneers. All veneers were fee from burned marks during drying test.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 학술대회지
• /
• pp.850-852
• /
• 2004

The usable output of glassware formation production line depends, among other factors, on the weight and shape of a lump of hot molten glass called a gob. In this paper, an automated image processing system for monitoring gob weight and shape on a production line is proposed. Present techniques often rely on manual weighing of gobs on a sample basis by manually controlling the gob feeder. The proposed automated image monitoring system checks the weight and shape of every free-falling gob before it reaches the mould. In this system, the estimated weight of the gob is sufficiently close to its actual weight.

• Journal of the Korean Wood Science and Technology
• /
• 제30권4호
• /
• pp.27-32
• /
• 2002

PEG 처리가 고함수율 상태의 방부처리 삼나무 원주가공재의 건조 할렬 방지 및 방부제의 침투성에 미치는 영향을 검토하였다. 농도 10%의 방부제(Basilit CFK) 용액에 1일간 침지 처리한 시험체의 표면에 노도 50%의 PEG-400을 각각 3, 5, 10획 도포하여 30일간 천연 건조한 후 할렬의 발생정도 및 변재부의 방부제 침윤도를 조사하였다. 변재부의 방부제 침윤도를 조사한 결과, 방부제 단독처리 시험체에서는 약 23.2%였으나 방부제 PEG 처리 시험체에서는 약 51.2~64.5%로 비교적 높은 값을 나타내 PEG처리에 의하여 방부제의 침투가 촉진된 것으로 추정되었다. 천연건조 기간 중에 방부제-PEG 처리 시험체에서의 건조 할렬 발생은 PEG 도포횟수의 증가와 함께 뚜렷하게 감소하였을 뿐만 아니라 발생된 몇 개의 할렬의 크기도 방부제 단독처리 시험체에서 발생한 것에 비하여 현저하게 작았다. 그러나 2개월간 옥외 폭로 후에는 방부제-PEG처리 시험체에서 많은 할렬이 발생하여 PEG 처리 효과가 인정되지 않았으나, PEG 처리 후, 폴리우레탄수지 래커로 도장 처리한 결과, 옥외 폭로기간 중에 할렬 발생이 뚜렷하게 방지되었다

• Journal of the Korean Wood Science and Technology
• /
• 제51권6호
• /
• pp.493-508
• /
• 2023

Round timber materials of 600 mm length, cut from large-cross-section round timber of red pine (Pinus densiflora S. et Z.) of 450 mm width and 4.2 m length, were prepared as the target of kiln drying in this study. After treating the target materials through end sealing (ES), end sealing - kerfing (ES-K), lateral sealing - end sealing - boring (LS-ES-B), or lateral sealing - partial end sealing (LS-PES), the effects of the treatment on the incidence of drying defects were determined. The target materials with exposed lateral surface and sealed cross surface were steamed at the initial temperature of 65℃ above the official pest control temperature of 56℃, followed by kiln drying toward the final temperature of 75℃. The target materials with sealed lateral surfaces, on the other hand, were dried at the initial temperature of 90℃ at almost the maximum temperature of conventional kiln drying, as there is no risk of early check formation caused by surface moisture evaporation. The final temperature was set at approximately 100℃. The drying time, taken for the target materials with initial moisture content of 70%-80% to reach the target moisture content of 19%, varied across treatment conditions. The measured drying time was 1,146 hours (approximately 48 days) for the timber with sealed cross surface and 745 hours (approximately 31 days) for the timber with sealed lateral surface, until the moisture content reached the target level. The formation of surface checks could not be prevented in the control and ES groups, but a definite preventive effect was obtained for the LS-ES-B and LS-PES groups.

• International Journal of Computer Science & Network Security
• /
• 제21권6호
• /
• pp.312-318
• /
• 2021

Lack of knowledge and digital skills is a threat to the information security of the state and society, so the formation and development of organizational culture of information security is extremely important to manage this threat. The purpose of the article is to assess the state of information security of the state and society. The research methodology is based on a quantitative statistical analysis of the information security culture according to the EU-27 2019. The theoretical basis of the study is the theory of defense motivation (PMT), which involves predicting the individual negative consequences of certain events and the desire to minimize them, which determines the motive for protection. The results show the passive behavior of EU citizens in ensuring information security, which is confirmed by the low level of participation in trainings for the development of digital skills and mastery of basic or above basic overall digital skills 56% of the EU population with a deviation of 16%. High risks to information security in the context of damage to information assets, including software and databases, have been identified. Passive behavior of the population also involves the use of standard identification procedures when using the Internet (login, password, SMS). At the same time, 69% of EU citizens are aware of methods of tracking Internet activity and access control capabilities (denial of permission to use personal data, access to geographical location, profile or content on social networking sites or shared online storage, site security checks). Phishing and illegal acquisition of personal data are the biggest threats to EU citizens. It have been identified problems related to information security: restrictions on the purchase of products, Internet banking, provision of personal information, communication, etc. The practical value of this research is the possibility of applying the results in the development of programs of education, training and public awareness of security issues.

• 한국과학교육학회지
• /
• 제13권1호
• /
• pp.56-65
• /
• 1993

The purpose of this study is to analyze the inquiry activities of SCIIS and Korea primary school science curricular meterials and to make suggestions for the improvement of inquiry learning based on the analysis The Scientific Inquiry Evaluation Inventory (SIEI: Myung Hur, 1984) was used to evaluate the inquiry activity content of the primary school "Science, Level-6" and "SCIIS, Level-6" textbooks. The results are as follows: 1) The inquiry activities of Korean science textbooks are stressing on gathering and organizing data, but rarely require students to formulate a hypothesis, to design an experiment. 2) The SCIIS textbooks relatively tended to put more weight on interpreting/ analysing data and hypothesizing/ designing experiments. 3)The Korean science textbooks had little concern about establishing hypothesis and designing experiments, interpreting / analysing data. 4) The SCIIS textbooks require students to perform a variety of inquiry skills when compare to Korean science textbooks. 5) Competition / Cooperation Scale checks the level of competition and cooperation among student teams inherent in science curricular materials. The result from each team is incorporated into the formation of a class result. The communication is required to formulate a synthesized class response, enhances cooperation among teams. The SCIIS(84%) is the higher than Korea(50%) in cooperation scale. 6) Korean science textbooks rarely require students to discuss about experiment when compare to SCIIS textbooks. 7) Korean science textbooks provide students with both inquiry problems and experimental procedure, or including answers SCIIS textbooks provide students with both inquiry problems and experimental procedure, or problems only. 8) The Korean textbooks emphasize demonstrating or verifying of the text while the SCIlS emphasize extending the content of the text in inquiry scope scsle. The inquiry pyramid which helps analysis the inquiry activity curriculum as a whole is one of type 1- the course is centered on gathering and organizing data. The SCIIS are better than the Korean science textbook in the light of proportion of interpreting / analysing data and hypothesizing / designing experiments.