• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.3
• /
• pp.768-776
• /
• 1994

This paper describes computer-aided forging design for rib/web shaped parts. In manufacturing a part by means of forging process, the first step is to design the forging. This is done by modifying the given machined part geometry according to the requirements of the forging process. Traditionally, this is done by experienced forging designers using empirical forging design guidelines. Generally, it would be neither possible nor practical to develop a system which encompasses the design of all types of forgings. Accordingly, forging design can be simplified by considering critical two dimensional cross sections of the machined part geometry. This system is composed of three modules(process variable decision module, forging design module and redesign module) and each module is carried out in regular sequence. In the process variable decision module, first of all, the undercut is checked and modified, and then deep recesses and holes difficult to forge are eliminated. Also parting line, forging plane, forging plan view area, forging weight and maximum size(maximum height or width)are determined. In the forging design module, the magnitude of various allowances, draft angle, minimum web thickness, corner and fillet radius are determined and then geometry modification is performed. Finally, since the design rules and databases used in this system are based on parameters of the forging geometry, such as the trimmed forging plan area, forging weight, forging maxmum size, plausible estimates need to be made for these parameters. Therefore, in the re-design module, the design process is iterated until a satisfactory forging is obtained.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.47-50
• /
• 2003

Hot-forging Process and die design was made for a large-scale compressor wheel of Ti-6Al-4V alloy with 2-D FE analysis. The design integrated the geometry-controlled approach and dynamic materials modelling(DMM). In order to obtain the processing contour map of Ti-6Al-4V alloy based on DMM, compression tests were carried out in the temperature range of 915$^{\circ}C$ to 1015$^{\circ}C$ and the strain range of 10$\^$-3/s$\^$-1/ to 10s$\^$-1/. In the die design of the compressor wheel using the rigid-plastic FE analysis, forging dimensional accuracy, the capacity of the forging machine and defect-free forging were considered as main design factors. The microstructure of hot forged wheel using the designed die showed a typical alpha-beta structure without forging-defects.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.756-759
• /
• 2003

Steam Generator is one of the most important structural part of nuclear power plant. It is manufactured by welding process of various steel forgings such as shell, head, torus and tube sheet. These steel forgings have been made by open die forging process. After steel melting and ingot making, open die forging has been carried out to get a good quality which means high soundness and homogeniety of the steel forgings by using high capacity hydraulic press. This paper introduced open die forging status and investigated forging method of the ultra large steel forgings which is used for the steam generator of 1000MW nuclear power plant. For the same thing. the type of steel forgings consisting steam generator is classified by shell, head, torus and tube sheet. And corresponding forging processes of the steel forgings have been investigated.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.1
• /
• pp.83-89
• /
• 2004

Flare nut is an important Part that used to joint a brake tube-end in automobiles. It was made of SWCH 10A by machining. But we studied to make it by metal forming. The main focus of this paper is to investigate an optimal forging processes for flare nut using the DEFORM$^{TM}$-3D. commercially available finite element code and tests. Actually an explicit finite element analysis of the flare nut forging processes has been carried out to predict an optimal shape of the flare nut and its results were reflected in the tests of the forging processes design for flare nut. The simulation results which had obtained from finite element analysis were contributed to the forging processes design for flare nut. An optimal shape of nave nut showed agreements with test results. Furthermore. this paper should contribute to a development of the forging process for a variety of parts.s.

• Transactions of Materials Processing
• /
• v.9 no.1
• /
• pp.52-58
• /
• 2000

Hot precision forging with a back pressure was investigated for manufacturing of compressor parts made of Al-Si alloy. Disk-shaped blank made of Al-Si alloy was hot forged, and ribs were formed by loading back pressure on their top. The influence of the back pressure and die temperature on forgeability and properties of parts made of Al-Si alloy were examined. Using the F.E.M. simulation, we found the optimum vallue of back-pressure. The prototypes of scroll parts were forged into the near-net shape and satisfied the required properties.

• Journal of Powder Materials
• /
• v.5 no.4
• /
• pp.319-323
• /
• 1998

Powder forging with a back pressure was investigated for production of automobile and compressor parts made of a rapidly solidified Al-Si alloy powder. Disk-shaped green compacts made of a rapidly solidified Al-Si alloy powder were hot forged, and hubs were formed by loading back pressure on their top. The influences of the back pressure and die temperatures on forgeabiliy and properties of parts made of a rapidly solidified Al-Si alloy powder were examined. This method was also applied to the production of a scroll part. The results of these studies are summarized as follows : 1. A back pressure on the hub top is very effective for consolidation and preventing crack formation in the hub. 2. When a back pressure tess than 98 MPa is applied, the forging pressure increases by the same amount of the applied back pressure. With more than 98 MPa, the forging pressure increases further due to an increased friction at the hub side. 3. Die temperatures higher than approximately 670k are needed in order to consolidate well the hub top without cracks.

• Transactions of Materials Processing
• /
• v.7 no.3
• /
• pp.291-297
• /
• 1998

A forging product in general is made through buster blocker and finisher processes. The dies used in these processes are designed by experienced forging engineers. In the present study an expert system is developed for the finisher die design of axisymmetric hot steel forging. It is a rule based system written in Fortran and AutoLISp operating on a personal computer. In this paper major rules consid-ered in the system are summarized and the capabilities of the system are examined through several examples.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.139-142
• /
• 2003

In this study, casting/forging process was used to produce an aluminum lower control arm for automobiles. Firstly, casting experiments were carried out to get an enhanced preform for forging the lower control arm. In the casting experiment, the effect of an additive, Sr, on the mechanical properties such as tensile strength and elongation and the microstructure of a cast preform were investigated. And a finite element analysis was peformed to determine an optimal configuration of the cast preform. Lastly, a forging experiment was carried out to make the final product of aluminum lower control arm by using the above cast preform. In the casting experiments, when 0.025% Sr was added into molten A356, the maximum values of tensile strength and elongation of the cast preform were obtained. In the forging experiment, It was confirmed that the optimal configuration of a cast preform predicted by FE analysis was very useful. The cast/forged product using designed preform was made without any defects.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.10a
• /
• pp.86-94
• /
• 1995

The rotary forging process has a potential for producing high-precision parts because of smaller forging forces and incrementally controlled deformation, especially in cold forging of intricate parts to net shape. But while thin circular plate are made by rotary forging, center thinning and fracture will occur under given conditions. The trouble has seriously influenced the quality of products and the spreading of this technique. This paper intends to explain the phenomenon of center thinning and gives a criterion of it. In order to confirm the validity of the proposed criterion, experiments have been carried out by using the rotary forging press which has been designed and constructed in our laboratory.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.06a
• /
• pp.180-187
• /
• 1995

Helical gears are machined from blanks, which are usually prepared by forging cylindrical billets at high temperatures through buster, blocker and finisher processes. As dimensions of the blank are closer to those of the machined part, machining cost can be more reduced. Therefore, there are a lot of efforts being made to optimize the forging processes in order to produce near-net shaped blanks. In the present investigation, a rigid viscoplastic finite element technique was used to analyze a helical gear blank hot forging processes and deformation, strain and temperature distributions, forging load variations during forging were obtained. In the paper, it is discussed how these results can be utilized to optimize die design, billet dimensions and press usage.