• Journal of the Korea Institute of Building Construction
• /
• v.12 no.1
• /
• pp.22-30
• /
• 2012

Four types of foaming agents, including Alcohol Ethoxy Sulfate (AES), Alpha Olefin Sulfonate (AOS), Vegetable Soap (VS), and Fe-Protein (FP), are widely used in the construction field. These have different surface tensions and viscosities in water of the same concentration, affecting the flow speed of liquid, size and distribution of foam, and foam stability. However, there is a lack of data regarding the properties of foam concrete using various foam agents. The purpose of this study is to investigate influence of foaming agents on the properties of foamed concretes with various densities. We find that the foaming agent type has little effect on the density, compressive strength, and thermal conductivity of foam concrete, but considerably affects the unit weight of foam, flow and flexural strength of foamed concrete. While almost all properties of foam concrete are affected by density in fresh or hardened state, the potential energy changed by slurry density and the viscosity of foam are dominant factors in the flowability of foam slurry.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.375-376
• /
• 2010

This study is shown the chemical characteristics by SEM and XRD for the Light-weight Foamed Concrete according to replacement ratio of WCP and the autoclave curing time. From the SEM of the Light-weight Foamed Concrete after hydrothermal raction, regardless of replacement ratio of WCP and the autoclave curing time, forms the crystal hydrates having various shapes such as board and fiber etc is generated. From the XRD, it seems that the tobermorite hydrate is originated from crystalized quartz.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05b
• /
• pp.449-452
• /
• 2005

Sound absorption coefficient is affected by void in sound absorbing materials, therefore it is important to analyze properties of void pore. Also, it can be used to estimate performance of foamed concrete when it is applied to absorb sound. The purpose of this study is to analyze the sound absorption coefficient and void characteristic of foamed concrete using bottom ash. As a result of experiment, it was determined that an increase in sound absorption coefficient is achieved by increasing added amount of foam.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.43 no.1
• /
• pp.1-7
• /
• 2023

A set of foamed concrete specimens with different densities were prepared, and several microscopic techniques, such as scanning electron microscope (SEM) and X-ray micro-computed tomography (micro-CT) were used to characterize the foamed specimens. The pore and solid characteristics of the specimens at different ages were examined to investigate the effect of aging on the materials. The compressive strength and the thermal conductivity of the foamed specimens were also evaluated, and the relationship between the material characteristics and properties was integrated to identify the effect of density and aging on the material properties.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.6
• /
• pp.130-137
• /
• 2013

This research was performed through the experimental design to get the statistical analysis on foamed concrete mixed plaster with hydrogen peroxide. In this experiment, we set the ratio of each material, which part of lightweight concrete, as experimental factors and evaluated on the mechanical properties by statistical analysis for response variables obtained from experiments. Experimental factors are plaster replacement, water binder ratio, and hydrogen peroxide ratio. Response variables are dry density, compressive strength, and flexural strength. Mixing design of the foamed concrete set up a total of 15 experimental points by Box-Behnken (BB) method of the response surface analysis. Thus, the results of a study were summarized as follows. Values of the probability in experimental factors (plaster replacement, water binder ratio and hydrogen peroxide ratio) on the response variables were estimated to be significant at the 95% of confidence limit. On response surface analysis for dry density of foamed concrete, water binder ratio and hydrogen peroxide ratio were estimated to be significant (${\alpha}$ = 0.05), and the relationship between the amount of void and the water content for dry density is inverse proportional. On response surface analysis for the compressive strength of foamed concrete, water binder ratio, hydrogen peroxide ratio and (hydrogen peroxide ratio)$^2$ was estimated to be significant (${\alpha}$ = 0.05). On response surface analysis for the flexural strength of foamed concrete, water binder ratio, hydrogen peroxide ratio was estimated to be significant (${\alpha}$ = 0.05). Through multi response surface analysis, we found the optimal area that meets performance goals.

• Journal of the Korea Concrete Institute
• /
• v.14 no.2
• /
• pp.207-215
• /
• 2002

This study is focusing on mixing the foamed concrete incorporated by waste expanded polystyrene(W-EPS), investigating the physical properties and offering a proper quality control method to the field engineers. Two types of W-EPS (type A and type B) were studied. Type A (B) had globular (crushed) shape and diameter of 3-5 (1-2) mm. The results show that the flow was suddenly reduced with increasing mixing quantity of two types, but it satisfies KS F 4039 until 60 ％ of mixing rate. In general, the absorption rate was suddenly reduced with increased mixing quantity of two types especially, in type A. Apparent specific gravity was 0.36∼0.53 and reduced with increasing mixing quantify of type A. But it increased in case of type B. Compressive strength and heat conduction rate increased with mixing with W-EPS than non-mixing W-EPS but reduced with mixing too much W-EPS. Based ong the results, it is believed that mixing with W-EPS can improve the recycle of industrial wastes and produce the high quality foamed concrete.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2007.11a
• /
• pp.19-22
• /
• 2007

This study discussed the prevention of the spalling and improvement of the fire resistance performance how to fill up lightweight foamed concrete on high strength RC column attached with the stone panel. The destructive spalling extremely occur caused by sudden high temperature and increased vapor pressure corresponding to falling the ston panel at all RC column, and the steel bar is exposed. The stone panel fall off about 30 minutes and spalling occur about 70 minutes on Plan RC column, fire endurance paint, and fire endurance mortar, so it can be confirmed that fire endurance paint and mortar, which is used as fire endurance material, are not effective. In the other side, it can be protected from fire about $120{\sim}140$ minutes when the lightweight foamed concrete is used as fire endurance material. For the weight loss after the fire test, plain is 33, fire endurance paint is 37%, and fire endurance mortar s 40.7%. And W/B 60%-3 is 53.4%, 60%-1.5 is 40.1%,65%-3 is 39.4%, and 65%-1.5% is 47.1. Overall, the weight loss of the plain is lower than that of the lightweight foamed concrete.

• Journal of the Korea Institute of Building Construction
• /
• v.9 no.4
• /
• pp.63-73
• /
• 2009

Recently, the use of lightweight panels in building structures has been increasing. Of the various lightweight panel types, styrofoam sandwich panels are inexpensive and are excellent in terms of their insulation capacity and their constructability. However, sandwich panels that include organic material are quite vulnerable to fire, and thus can numerous casualties in the event of a fire due to the lack of time to vacate and their emission of poisonous gas. On the other hand, lightweight foamed concrete is excellent, both in terms of its insulation ability and its fire resistance, due to its Inner pores. The properties of lightweight concrete is influenced by foaming agent type. Accordingly, this study investigates the insulation properties by foaming agent type, to evaluate the possibility of using light-weight foamed concrete instead of styrene foam. Our research found thatnon-heating zone temperature of lightweight foamed concrete using AP (Aluminum Powder) and FP (animal protein foaming agent) are lower than that of light-weight foamed concrete using AES (alkyl ether lactic acid ester). Lightweight foamed concrete using AES and FP satisfied fire performance requirements of two hours at a foam ratio 50, 100. Lightweight foamed concrete using AP satisfied fire performance requirements of two hours at AP ratio 0.1, 0.15. The insulation properties were better in closed pore foamed concrete by made AP, FP than with open pore foamed concrete made using AES.

• Journal of the Korea Institute of Building Construction
• /
• v.11 no.6
• /
• pp.557-566
• /
• 2011

The surfactants facilitate the formation of foam bubbles under a proper condition and provide stability of foam bubbles by decreasing the surface tension of solutions and increasing the viscosity of foam surface. However, there have been almost no practical data of foam concrete in this regard so far. This study aims to understand the effects of foaming agents such as anionic synthetic surfactant and anionic natural material surfactant on the low density foamed concrete. From the experiment, the vegetable soap of anionic natural material surfactants showed a higher foaming rate, more open pores, slightly lower compressive strength, and a higher permeability coefficient compared to the vegetable soap of anionic synthetic surfactants. It is believed that the natural material surfactants make not only the surface tension of the solution low but also the viscosity of slurry high.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.06a
• /
• pp.130-131
• /
• 2020

This study manufactured the porous foamed concrete granules coated with TiO₂ Nanoparticles, to widen the specific surface area. The Removal rate of concrete granules coated with TiO₂ Nanoparticles was average 56.7%, which was approximately 2.3 time higher than that of the conventional surface TiO₂ coating.