• 한국가스학회지
• /
• 제8권2호
• /
• pp.1-7
• /
• 2004

경질폴리우레탄 폼 제조 시 water, HFC-365mfc, HFC-245fa, HCFC-l4lb, CFC-11, n-pentane을 사용하여 단일발포제가 폼의 물성에 미치는 영향을 알아보고, HFC-365mtc 를 주 발포제로 사용하고 water, HFC-245fa, HCFC-l4lb, CFC-11, n-Pentane을 보조발포제로 사용하여 혼합 발포제(co-blowing agent)가 폼의 물성에 미치는 영향을 고찰하였다. 단일 발포제의 영향에서 압축강도는 물의 경우가 3.83kg/m^2으로 가장 큰 값을 나타내었으며 Scanning electron/microscopy(SEM)분석 결과 HFC-245fa와 HFC-365mfc의 경우가 기공분포 크기가 가장 작은 것으로 관찰이 되었다. 열전도도는 CFC-11, HFC-245fa와 HFC-365mfc의 경우가 낮은 열전도도 값을 보여서 폼의 열전도도는 기공크기와 발포제의 열전도도에 의존함을 알 수 있었다. 혼합 발포제의 영향에서는 HFC-245fa를 $30mo1e\%$로 사용한 경우가 가장 높은 기계적 물성 값을 나타내었으며 이는 SEM 분석 결과, HFC-245fa를 보조 발포제로 사용한 경우가 가장 작은 기공분포크기를 나타내었기 때문이었다. 혼합 발포제의 영향에서도 폼의 열전도도는 기공크기와 발포제의 열전도도에 의존함을 확인 할 수 있었다.

• Elastomers and Composites
• /
• 제50권1호
• /
• pp.13-17
• /
• 2015

A study of the effects of MWCNT as a nucleating agent on the formation reactions of the rigid polyurethane foams (RPUFs) was carried out. Sample PUFs, formulated with grease-type master batch of MWCNT/surfactant, were fabricated by free-rising method. Temperature changes with time during foaming process were measured using a digital thermometer. RPUF foaming process was observed to undergo 2-step processes with temperature inflection around 60 sec after the start of reaction, and then reached slowly the max. temperature. While the max. temperature of neat PUF was measured as ca. $120^{\circ}C$, that of the samples with MWCNT were as higher value as ca. $130^{\circ}C$, and, even the time to reach that temperature was reduced by about 15 sec. Average cell size of PUF samples decreased from 185.1 for the neat PUF to $162.9{\mu}m$ for the sample of 0.01 phr of MWCNT. As the result, it was considered that MWCNT in RPUF foaming process could play a roll both as a nucleating agent and as a catalyst.

• 공업화학
• /
• 제17권4호
• /
• pp.361-368
• /
• 2006

본 연구는 독립적 기공(또는 기포)을 함유하고 특히, $50kg_f/cm^2$의 압력에도 외형의 변화가 없고, 상온의 액화석유가스 (liquefied petroleum gas; LPG)에 72 h 침적시 무게 변화율이 5 wt% 이내인 LPG 고압 탱크용 발포 부표의 제조 기술을 개발하는데 목적이 있다. 각각의 다른 유황(325 Mesh와 400 Mesh)과 발포제(foaming agent)로 제조된 부표의 내압침적 실험에서 무게 변화율은 큰 차이를 보이지 않았으나 유황 400 Mesh와 발포제 AC를 이용한 부표의 기공이 더 작고 독립 기포율이 높았다. $50kg_f/cm^2$ 수압 실험에서 중립열분해(medium thermal; MT) 카본을 사용한 부표가 중보강성(semi reinforcing furnace; SRF) 카본보다 작은 무게 변화율을 나타내었다. 또한, 제조된 부표를 후처리($60^{\circ}C$, 24 h)한 경우 부표내 기공벽의 경도와 내압성이 증가되었다. 한편, 제조된 부표의 비중 0.30 이하인 제품은 찌그러지거나 깨지는 현상이 발생하고 비중이 0.35 이상으로 높으면 부력이 떨어져 부표로서 기능을 하지 못하였다. 그러므로, $50kg_f/cm^2$의 내압성을 가지기 위해서는 비중이 0.30~0.35인 부표가 가장 우수한 성능을 갖는 것으로 판단되었다.

• 공업화학
• /
• 제33권4호
• /
• pp.386-393
• /
• 2022

본 연구에서는 실란 커플링제 옥틸트리메톡시실란(octyltrimethoxysilane, OTMS)을 사용하여 친수성 탄산칼슘(CaCO₃) 나노입자의 표면을 개질하였으며, OTMS에 의한 CaCO₃ 나노입자의 표면 개질은 FT-IR, DSC, XRD XPS 및 TGA 분석을 통하여 확인하였다. 또한 부유 시험과 접촉각 측정을 통하여 OTMS 농도가 CaCO₃ 나노입자의 표면 소수성 변화에 미치는 영향에 관하여 살펴보았다. 부유 시험 결과에 따르면 1 wt% OTMS 농도 조건에서 측정한 active ratio 값이 97.0 ± 0.5%로서, OTMS가 CaCO₃ 나노입자 표면을 매우 효율적으로 소수화 개질하는 실란 커플링제임을 알 수 있었다. 또한 OTMS로 개질된 CaCO₃ 나노입자 1 wt%를 함유하는 수용액에 대한 기포 안정성 측정 결과, OTMS 농도가 1 wt%인 조건에서 가장 안정한 기포가 생성되며, 접촉각은 91.8 ± 0.7°임을 확인하였다. 또한 동일한 1 wt% OTMS 농도 조건에서 에멀젼 입자 크기가 가장 작은 안정한 상태의 에멀젼이 형성됨을 확인하였다. 이러한 결과들은 OTMS로 개질된 CaCO₃ 나노입자가 다양한 산업 응용 분야에서 기포 안정화제 및 에멀젼 유화제로서 적용이 가능함을 의미하는 것이다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2005년도 춘계 학술기술논문발표대회 논문집
• /
• pp.93-98
• /
• 2005

The purpose of this study was to analyze the compression strength research by aerated concrete as mixing ratio This Study used foaming-agent and produced aerated concrete by pre-foam way that is used in construction site. An experiment changes unit cement amount, w/c and the glass fiber mixing rate and 'measured capacity change, unit capacity weight and compressive strength. The results obtained from experimental study are as following; Research to reduce unit capacity weight in condition more than unit cement amount 500kgf is considered should be gone side by side. The highest compressive strength result appeared in aerated concrete that cement amount 600kgf and w/c ratio $45\%$, $50\%$. compressive strength was increased maximum $34%$ when glass fiber $0.7\%$ addition cause by coherence enlargement to enlargement of cement paste and glass fiber addition per unit volume

• 한국응용과학기술학회지
• /
• 제23권1호
• /
• pp.37-44
• /
• 2006

Solvent-free low foaming scouring agents (LFSC) were prepared by blending of 2-ethylhexylaminoethyl sulfate (2-EHAS), POE(10) octadecylbenzyl- ammonium chloride (POBAC) and Sedlan FF-200 (FF-200). As the results of several tests, 2-EHAS/POBAC/FF-200/water (8g/12g/20g/60g) mixture (LFSC-5) showed good cleaning power, penetrating ability and stability to alkali, and gave less problem in water pollution. The foaming power of LFSC-5 measured by Ross and Miles method was 8mm foam height immediately after foaming, and that measured by Ross and Clark method was less than 300mm foam height at $30^{\circ}C$, and 18mm at $80^{\circ}C$. As a result, LFSC-5 proved a good low foaming scouring agent for fiber.

• 한국응용과학기술학회지
• /
• 제21권2호
• /
• pp.156-163
• /
• 2004

Low foaming scouring agents (LSSA) were prepared by blending of amine salt of dodecylbenzene sulfone, poly (PO-b-EO) glycol, Newpol PP-2000, MJU-100, ethylene glycol and organic solvent. As the results of several tests, LSSA-2 showed good scouring effect, penetrating ability and emulsifiability, and showed not much water pollution. The foaming power of LSSA-2 measured by Ross & Miles method was 11mm foam height immediately after foaming. And the foaming power of LSSA-2 measured by Ross & Clark method were less than 310mm foam height at $30^{\circ}C$, 17mm at $80^{\circ}C$. As a result, LSSA-2 was proved as a good foaming scouring agent.

• 한국주조공학회지
• /
• 제25권5호
• /
• pp.203-208
• /
• 2005

The main emphasis of this study is to optimize the process variables for manufacturing aluminum foam materials by direct foaming of remelted aluminum scraps. Aluminum foams were fabricated from two different raw materials, pure aluminum and used beverage cans. For both cases, $TiH_{2}$ was used as a foaming agent. Calcium was added as a thickener for the foaming of pure aluminum and no thickener was added for that of used beverage Cans because the pre-existing oxides of the used beverage cans are used as a thickener. Calcium and $TiH_{2}$ content varies from 0.5wt.% to 2.0wt.% and from 0.5wt.% to 1.5wt.%, respectively. The processing conditions, such as the effect of calcium on the melt viscosity, foaming temperature, and the optimum amount of the foaming agent with regard to the melt viscosity were discussed.

• 한국응용과학기술학회지
• /
• 제20권2호
• /
• pp.81-86
• /
• 2003

To prepare alkaline degreasing agents(SADAs), tetrasodium pyrophosphate(TSPP), $Na_2CO_3$, Tetronix T-701 (T-701), Na-dioctyl sulfosuccinate(303C), Demol C, and MJU-100A were blended. The prepared degreasing agents were tested with steel specimens and the results were as follows. The degreasing powers of SADA-6($Na_2CO_3$ 50g/TSPP 25g/T-701 10g/303C 15g/Demol C 12g/MJU-100A 8g/water 130g mixture) for press-rust preventing oil were 98% and 99% degreasing at 4wt%, 70 $^{\circ}C$ and 90 $^{\circ}C$, respectively; for quenching oil, the degreasing power of SADA-6 was 92% degreasing at 4wt% and 70 $^{\circ}C$. From these results, it was proved that the SADA-6 exhibits a good degreasing power. Foam heights measured immediately after foaming by Ross & Miles method and Ross & Clark method at 6wt% and 60 $^{\circ}C$ were 16mm and 40mm, respectively. SADA-6 was proved a good low foaming degreasing agent.

• 한국응용과학기술학회지
• /
• 제21권4호
• /
• pp.306-312
• /
• 2004

An acid cleaning agent (AACA) for aluminum was prepared by blending of sorbitol, n-octanoic acid, MJU-100A, Tetronix T-701, PPA-23, C8-83 and phosphoric acid. With the prepared AACA, degreasing, foam height, etching and derusting tests were carried out. As a result, AACA-4 and AACA-7 showed better cleaning ability than commercial acid cleaning agents.