• Clean Technology
• /
• v.18 no.2
• /
• pp.170-176
• /
• 2012

A series of acrylic copolymers containing perfluoroalkyl acrylate were synthesized by 2-step emulsion polymerization of variety of acrylate monomers (ethyl acrylate, butyl acrylate or methyl methacrylate) with perfluoroalkyl ethyl acrylate (PFA) and glycidyl methacrylate (GMA) monomers. This study focused on effects of monomer compositions (the kind of acrylate monomer, contents of PFA and GMA) and composition of surfactants [(sodium dodecyl sulphate/nonylphenol 10mole ethoxylate (NP-10)] and initiator content on the contact angles and surface free energy. It was found that the copolymer having an optimum composition (BA : 87 wt%, GMA : 8.7 wt% and PFA : 4.3 wt%) was shown to be quite surface active [surface free energy : 19.89 mN/m and contact angles : $103.5^{\circ}$ (water) and $78.7^{\circ}$ (methylene iodide)] in the solid state. This result suggests that the optimal copolymer containing fluorinated monomer synthesized in this study have high potential as a low surface energy material, which may have high oil- and water-repellent surface and have been proposed as acrylic syntan for leather and also as soil-resistant/oil and water repellent coating for textiles and wood etc.

• Polymer(Korea)
• /
• v.34 no.6
• /
• pp.540-546
• /
• 2010

In this manuscript, in order to reduce methanol permeability and, at the same time, to increase proton conductivity THS-PSA containing silica compound, responsible for methanol permeability reduction, and sulfonic acid, responsible for proton conductivity enhancement, was applied onto PVA/PSSA-MA membranes. And in order to improve durability, the resulting membranes, PVA/PSSAMA/THS-PSA, were exposed to 500ppm F2 gas at varying reaction times. The surface-fluorinated membranes were characterized through the measurement of contact angles, thermo-gravimetric analysis, and X-ray photoelectron spectroscopy to observe the physico-chemical changes. For the evaluation of the electro-chemical changes in the resulting membranes, its water contents, ion exchange capacity, proton conductivity, and methanol permeability were measured and then compared with the commercial membrane, Nafion 115. Finally, the membran electrode assembly(MEA) was prepared and the cell voltage against the current density was measured. As fluorination time increased, the contents of F2 increased up to maximum 4.3% and to depth of 50 nm. At 60 min of fluorination, the proton conductivity was 0.036 S/cm, larger than Nafion 115 at 0.024 S/cm, and the methanol permeability was $9.26E-08cm^2/s$, less than Nafion 115 at $1.17E-06cm^2/s$.

• Polymer(Korea)
• /
• v.34 no.1
• /
• pp.1-7
• /
• 2010

To enhance the transport properties of gas separation membrane, we prepared 6FDA-6FpDA based polyimide membrane with PMMA-graft-silica nanoparticles. The silica was grafted PMMA which is miscible with 6FDA-based polyimide after surface treatment by 3-methacryloxypropyltrimethoxysilane ($\gamma$-MPS). The untreated silica/6FDA-6FpDA membrane showed greater permeability and less selectivity than PMMA-g-silica/6FDA-6FpDA due to its low dispersion. The transport properties of PMMA-g-silica/6FDA-GFpDA membrane were measured as a function of filler concentration. These membranes were evaluated using pure gases (He, $O_2$, $N_2$, $CO_2$). The increase in permeation was attributed to changes in the free volume distribution until 1 wt%. After 1 wt%, the permeability was decreased by excess silica which decreased effective area in polymer matrix. The selectivity was decreased with increasing permeability on the whole. However, the selectivity of $CO_2$ showed more enhance value.

• Membrane Journal
• /
• v.16 no.3
• /
• pp.221-229
• /
• 2006

This study is about the preparation and characterization of sulfonated random copolymer membranes containing perfluorocyclobutane (PFCB), fluorenyl, and sulfonyl units. The polymers were prepared through three synthetic steps, that is, the synthesis of a trofluorovinylether-terminated monomer, its thermal polymerization, and post-sulfonation using chlorosulfonic acid. A series of sulfonated random copolymers with different ion exchange capacity (IEC) were prepared by changing contents of fluorenyl uints in polymers with fixed molar ratio of chlorosulfonic acid during the post-sulfonation reaction. All the synthesized compounds were characterized by FT-lR, $^1H-NMR$, $^{19}F-NMR$, and Mass spectroscopy. As the content of sulfonated fluorenyl units increased, the IEC, water uptake, and ion conductivity of the sulfonated random copolymer membranes increased. The sulfonated random copolymer S-1 and S-2 showed higher values of ion conductivity than the Nafion-115 in a wide range of temperatures ($25{\sim}80^{\circ}C$).

• Korean Chemical Engineering Research
• /
• v.57 no.3
• /
• pp.413-419
• /
• 2019

In the recent, as a world demand of energy resources has been transformed from fossil fuels to hydrogen-based clean energy resources, a huge attention has been attracted to increase the performance and decrease a production cost of core materials in fuel cell technology. The utilization of reinforced composite membranes as electrolytes in the polymer electrolyte membrane fuel cells can reduce the use of high cost perfluorosulfonic acid (PFSA), mitigate the cell impedance, and improve the dimensional stability as well as the interfacial stability, giving rise to achieve both an improved performance and a reduction of production costs of the fuel cell devices. In this study, we investigate the effects of physical characteristics and cell performances according to the various ionomer solvents in the solution based manufacturing process of reinforced composite electrolyte membrane.

• Composites Research
• /
• v.30 no.1
• /
• pp.41-45
• /
• 2017

Magnetite nanoparticles were synthesized by adding an ammonium hydroxide to a mixed solution of iron (II) and (III) chlorides. A silicon surfactant of ${\alpha},{\omega}$-(3-aminopropyl)polydimethylsiloxane was adsorbed on the particles as dispersant and a polydimethylsiloxane polymer was used to prepare ferrofluids of silicone oil base. Fluorinated surfactants of anionic ammoniated perfluoroalkyl sulfonamide and nonionic fluoroaliphatic polymeric esters were applied to the particles and a perfluoropolyether was used to prepare ferrofluids of fluorine oil base. The experimental conditions were used for preparing the ferrofluids with concentrations of 200, 300 and 400 mg/mL, and density, magnetization and viscosity of the products were characterized. The density values increased in proportion to the concentration, indicating 1.11-1.27 g/mL for silicone-oil-based fluids and 1.95-2.10 g/mL for fluorine-oil-based fluids in the range of 200-400 mg/mL. The saturation magnetization of the silicone-oil-based and fluorine-oil-based fluids indicated 14.7, 24.4, and 30.7 mT and 15.8, 23.3, and 33.7 mT for 200, 300, and 400 mg/mL, respectively, depending on the content of magnetic particles in the fluid. The viscosity of the silicone-oil-based ferrofluids was highly stable compared to that of the fluorine-oil-based with increasing temperatures. The ferrofluids are usually applied to seals and speakers with the silicone base and to seals with the fluorine base.

• Applied Chemistry for Engineering
• /
• v.27 no.5
• /
• pp.467-471
• /
• 2016

New electron deficient moiety, 6,7-difluoro-2,3-dihexylquinoxaline, was developed for the push-pull type copolymer for organic photovoltaics (OPVs). The PFDTQxF with lower HOMO energy level was synthesized using fluorene and 6,7-difluoro- 2,3-dihexylquinoxaline by Suzuki polymerization. The PFDTQxF thin film shows two absorption peaks at 368 and 493 nm. The HOMO and LUMO energy levels of PFDTQxF are calculated -5.55 and -3.91 eV, respectively. The device comprising PFDTQxF showed a $V_{OC}$ value of 0.47 V, a $J_{SC}$ value of $4.48mA/cm^2$, and a FF of 0.32, which yielded PCE of 0.78%, under the illumination of AM 1.5.

• Fire Science and Engineering
• /
• v.24 no.2
• /
• pp.21-30
• /
• 2010

We have test chemical resistance and flame retardant properties of chemical protective clothing Fabrics by the ASTM and ISO standard methods. The flame retardant test results show that polyethylene is poor in flame resistance but fluoroelastomer add to decabrom is excellent in flame resistance. Especially, nowadays heat protective clothing for firefighters, which is aluminized film layers laminated to aramid fabric, show the excellent flame resistance. However, the chemical resistance test results show that aluminium is high corrosive in 4M NaOH solution alone. The problem of corrosion can be overcome by employing multiple barrier film. Also, based on the result of flame retardant test, duel skin of polymer barrier film add to aluminum film and single skin of fluorinated rubber with flame retardant materials seems to be fit for the chemical protective clothing. Also the thermal protection and heat transfer test results show that TPP and HTI is increased assured that the continued study on fire risk assessment & chemical resistance of chemical protective clothing fabrics will contribute to the upgrade the performances of chemical protective clothing fabrics.

• Journal of Adhesion and Interface
• /
• v.7 no.2
• /
• pp.19-25
• /
• 2006

Since the enzymatic degradation of microbial poly(hydroxylalkanoate)s (PHAs), such as poly[(R)-3-hydroxybutyrate] and poly[(R)-3-hydroxybutyrate-co-3-hydroxyvalerate] initially occurs by a surface erosion process, their degradation behaviors can be controlled by the change of surface property. In order to control the rate of enzymatic degradation, plasma modification technique was applied to change the surface property of microbial PHAs. The surface hydrophobic and hydrophilic properties of PHA films were introduced by $CF_3H$ and $O_2$ plasma exposures, respectively. The enzymatic degradation was carried out at $37^{\circ}C$ in 0.1 M potassium phosphate buffer (pH 7.4) in the presence of an extracellular PHB depolymerase purified from Alcaligenes facalis T1. The results showed that the significant retardation of initial enzymatic erosion of $CF_3H$ plasma-treated PHAs was observed due to the hydrophobicity and the enzyme inactivity of the fluorinated surface layers while the erosion rate of $O_2$ plasma-treated PHAs was not accelerated.

• Journal of the Korean Electrochemical Society
• /
• v.19 no.2
• /
• pp.39-44
• /
• 2016

Oxygen reduction reaction in the fuel cell (ORR) plays a dominant role in the overall reaction. In addition, the low compatibility between the membrane and the binder consisted of different materials, greatly reduces the efficiency of the fuel cell performance. In view of these two problems, geometrically modified copolymers with 9.9_Bis (4-hydroxyphenyl) were synthesized via condensation reaction instead of conventional biphenol and were adopted as hydrocarbon ionomer binders. By utilizing these binders, two kinds of MEAs using fluorinated Nafion membrane and hydrocarbon based membrane were manufactured in order to electrochemical performance evaluation. With current-voltage curves, there was no significant difference in the 0.6 V when two types of membrane were applied. Also, tafel slope became considerably lower as compared to the Nafion membrane. Thus, it is determined that the new hydrocarbon binder is expected to contribute the improvement in performance of fuel cells.