• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.96.2-96.2
• /
• 2017

This research was conducted to investigate the electrochemical properties of the thin air-formed oxide film-covered AZ31 Mg alloy. In this work, native air-formed oxide films on AZ31 Mg alloy samples were prepared by knife-abrading method and the changes in the electrochemical properties of the air-formed oxide film were investigated in seven different electrolytes containing the following anions $Cl^-$, $F^-$, $SO{_4}^{2-}$, $NO_3{^-}$, $CH_3COO^-$, $CO{_3}^{2-}$ and $PO{_4}^{3-}$. It was observed from open circuit potential (OCP) transients that the potential initially decreased before gradually increasing again in the solutions containing only $CO{_3}^{2-}$ or $PO{_4}^{3-}$ ions, indicating the dissolution or transformation of the native air-formed oxide film into new more protective surface films. The Nyquist plots obtained from electrochemical impedance spectroscopy (EIS) showed that there was growth of new surface films with immersion time on the air-formed oxide film-covered specimens in all the electrolytes; the least resistive surface films were formed in fluoride and sulphate baths whereas the most protective film was formed in phosphate bath. The potentiodynamic polarization curves illustrated that passive behaviour of AZ31 Mg alloy under anodic polarization appears only in $CO{_3}^{2-}$ or $PO{_4}^{3-}$ ions containing solutions and at more than $-0.4V_{Ag/AgCl}$ in $F^-$ ion containing solution.

• Journal of Microbiology and Biotechnology
• /
• v.16 no.2
• /
• pp.264-271
• /
• 2006

Two fibrinolytic enzymes were purified from the culture supernatant of Fomitella fraxinea mycelia by ion-exchange and gel filtration chromatographies, and were designated as F. fraxenia proteases 1 and 2 (FFP1 and FFP2). The apparent molecular masses of the enzymes were estimated to be 32 kDa and 42 kDa, respectively, by SDS-PAGE and gel filtration chromatography. Both enzymes had the same optimal temperature ($40^{\circ}C$), but different pH optima (10.0 and 5.0 for FFP1 and FFP2, respectively). FFP1 was relatively stable at pH 7.0-9.0 and temperature below $30^{\circ}C$, whereas FFP2 was very stable in the pH range of 4-11 and temperature below $40^{\circ}C$. FFPI activity was completely inhibited by phenylmethylsulfonyl fluoride (PMSF) and aprotinin, indicating that this enzyme is a serine protease. The activity of FFP2 was enhanced by the addition of $CO^{2+}$ and $Zn^{2+}$ and inhibited by $Cu^{2+},\;Ni^{2+}$, and $Hg^{2+}$. Furthermore, FFP2 activity was strongly inhibited by EDTA and 1,10-phenanthroline, implying that the enzyme is a metalloprotease. Both enzymes readily hydrolyzed fibrinogen, preferentially digesting the $A{\alpha}$- and $B{\beta}$-chains of fibrinogen over ${\gamma}$-chain. FFP1 showed broad substrate specificity for synthetic substrates, but FFP2 did not. $K_{m}$ and $V_{max}$ values of FFP1 for a synthetic substrate, N-succinyl-Ala-Ala-Pro-Phe-pNA, were 0.213 mM and 39.68 units/ml, respectively. The first 15 amino acids of the N-terminal sequences of both enzymes were APXXPXGPWGPQRIS and ARPP(G)VDGQ(R,I)SK(L)ETLPE, respectively.

• Proceedings of the KIEE Conference
• /
• 2001.07e
• /
• pp.35-39
• /
• 2001

The purpose of this paper is improvement the piezoelectric of Polyvinylidene fluoride(PVDF) organic thin films is fabricated by vapor deposition method. The piezoelectric of PVDF organic thin films attributed to dipole orientation in crystalline region. Also, the piezoelectric characteristic reduced that dipole moments orientation in crystalline region interfered with impurity carriers. Therefore, PVDF organic thin films fabricated with high substrate temperature condition for crystallinity improvement. The crystallinity of PVDF organic thin films fabricated by this condition increase from 47 to 67.8%. The ion density of PVDF organic thin films fabricated by substrate temperature variation from $30^{\circ}C$ to $105^{\circ}C$ decreased from $1.62{\times}10^{16}cm^3$ to $6.75{\times}10^{11}cm^3$ when temperature and frequency were $100^{\circ}C$, 10Hz, respectively. The $d_{33}$ and piezo-voltage coefficient of PVDF organic thin films increased from 20pPC/N to 33pC/N and $162.9{\times}10^{-3}V{\cdot}m/N$ to $283.2{\times}10^{-3}V{\cdot}m/N$, respectively. For the sake of the applications of piezoelectric sensor, we analyzed the output voltage characteristic as a function of the distance between an oscillator of 28kHz and PVDF organic thin film transducer. From this, we found that the output voltage is inversely proportional to the distance. At this time, the period was about $35.798{\mu}s$ and equal the oscillator frequency.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.4
• /
• pp.1153-1159
• /
• 2013

A novel solid-contact indium(III)-selective sensor based on bis-(1H-benzimidazole-5-methoxy-2-[(4-methoxy-3, 5-dimethyl-1-pyridinyl) 2-methyl]) thiosulfinate, known as an omeprazole dimer (OD) and a neutral ionophore, was constructed, and its performance characteristics were evaluated. The sensor was prepared by applying a membrane cocktail containing the ionophore to a graphite rod pre-coated with polyethylene dioxythiophene (PEDOT) conducting polymer as the ion-to-electron transducer. The membrane contained 3.6% OD, 2.3% oleic acid (OA) and 62% dioctyl phthalate (DOP) as the solvent mediator in PVC and produced a good potentiometric response to indium(III) ions with a Nernstian slope of 19.09 mV/decade. The constructed sensor possessed a linear concentration range from $3{\times}10^{-7}$ to $1{\times}10^{-2}$ M and a lower detection limit (LDL) of $1{\times}10^{-7}$ M indium(III) over a pH range of 4.0-7.0. It also displayed a fast response time and good selectivity for indium(III) over several other ions. The sensor can be used for longer than three months without any considerable divergence in potential. The sensor was utilized for direct and flow injection potentiometric (FIP) determination of indium(III) in alloys. The parameters that control the flow injection method were optimized. Indium(III) was quantitatively recovered, and the results agreed with those obtained using atomic absorption spectrophotometry, as confirmed by the f and t values. The sensor was also utilized as an indicator electrode for the potentiometric titration of fluoride in the presence of chloride, bromide, iodide and thiocyanate ions using indium(III) nitrate as the titrant.

• Journal of Microbiology and Biotechnology
• /
• v.6 no.1
• /
• pp.1-6
• /
• 1996

A bacterial strain NS70 producing an alkaline protease was isolated from soil samples taken near a hot spring and identified as Bacillus licheniformis by its morphological and physiological properties and cellular fatty acid analysis. The isolated alkaline protease was purified by ammonium sulfate fractionation, DEAE-, CM-, and Phenyl-Sepharose column chromatography. The molecular weight of the purified enzyme was estimated to be 32, 000 Da by sodium dodecylsulfate polyacrylamide gel electrophoresis. Its optimal pH and temperature for proteolytic activity against Hammarsten casein were 12 and $65^{\circ}C$, respectively. The enzyme was stable at alkaline pH range from 6.0 to 12.0, and fairly stable up to $65^{\circ}C$. The enzyme was inhibited by phenylmethylsulfonyl fluoride but not by EDTA and N-ethylmaleimide indicating that the enzyme is serine protease. Enzyme activity was markedly inhibited by $Hg^{2+}$ and $Cu^{2+}$. Autolytic phenomena were observed on purified protease NS70 but autolysis was reduced by the addtion of $Ca^{2+}$ ion or bovine serum albumin.

• Journal of the Korean Chemical Society
• /
• v.47 no.2
• /
• pp.109-114
• /
• 2003

The electronic absorption spectra of trans-$[CrX_2([15]aneN_4)]ClO_4\;([15]aneN_4$=1,4,8,12-tetraazacyclopentadecane; X=F, Cl) complexes have been interpreted using the ligand field theory. An AOMX program is used to optimize the differences between the calculated and the observed positions for the spin-allowed transition bands. The crystal field theory(CFT) parameter is directly related to the angular overlap model(AOM), normalized spherical harmonic hamiltonians(NSH), and semiempirical parameters. The various ligand field parameters are discussed in terms of their chemical significances. According to the ligand field analysis, we can confirm that the fluoride ligand is a very strong ${\sigma}-$ and ${\pi}-$donor while the chloride has weak ${\sigma}-$ and ${\pi}-$donor properties toward chromium(III) ion.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.5
• /
• pp.525-532
• /
• 1992

Fluorine-doped YBaS12TCuS13TOS17-xTFS1yT superconducting materials with y varing two orders of magnitude form 0.02 to 2.0 have been prepared by a sol-gel process by using metal nitrate salts, sodium hydroxide and sodium fluoride. Fluorine contents have been measured using an ion-selective electrode. All fluorine doped as reactant were found to be present in the resulted samples. From the observation of XRD it has been concluded that the samples with y 0.2 formed simply the single phase of perovskite structure, whereas those with y 0.5 yielded together some compounds such as BaFS12T, YFS13T and CuO in the resulted samples. The observation of solid state S019TF NMR has been carried out in order to check whether fluorine was actually incorporated into the lattice sites, and the experimental results revealed that the mole ratio of fluorine incorporated into the lattice sites of YBaS12TCuS13TOS17-xT was approximately 0.2 per mole of the compound. Also electrical resistivity measurement indicated that onset transition temperature has the tendency to increase slightly with increasing y in the dilute region as y 0.2.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.3
• /
• pp.181-185
• /
• 2020

Hazardous and noxious substance (HNS) detection sensors were fabricated using multi-walled carbon nanotubes (MWCNTs) and various binder materials for ion batteries. To obtain uniformly printed films, the printing precision according to the substrate cleaning method was monitored, and the printing paste mixing ratio was investigated. Binders were prepared using styrene butadiene rubber + carboxymethyl cellulose (SBR+CMC), polyvinylidene fluoride + n-methyl-2-pyrrolidene (PVDF+NMP), and mixed with MWCNTs. The surface morphology of the printed films was examined using an optical microscope and a scanning electron microscope, and their electrical properties are investigated using an I-V sourcemeter. Finally, sensing properties of MWCNT printed films were measured according to changes in the concentration of the chemical under the various applied voltages. In conclusion, the MWCNT printed films made of (SBR+CMC) were found to be feasible for application to the detection of hazardous and noxious chemicals spilled in seawater.

• Journal of Periodontal and Implant Science
• /
• v.29 no.2
• /
• pp.401-415
• /
• 1999

Root surfaces affected by periodontal disease undergo various forms of changes. Cementum exposure from gingival recession may result in absorption of calcium, phosphorus, and fluoride and subsequent hypermineralization and increased radiodensity. Although some reports have suggested that inorganic content with root cementum might show various changes depending upon age or extent of periodontal disease, but no consensus can be reached regarding the the distribution of various elements. The present study examines the difference in mineral content between healthy and periodontal diseased roots by analyzing three areas per tooth along the root surface in cervico-apical direction using electron probe and scanning electron microscope. Healthy tooth that was extracted for orthodontic purpose was used as control. Experimental teeth include those with periodontal pocket depth exceeding 6mm and those with gingival recession and periodontal pocket depth of 2-4mm. Levels of Ca, P, Mg and Na were measured using wavelength dispersive x-ray spectrometer at three areas per tooth. The examined areas were located apical to cemento-enamel junction in control and periodontal ligament-depleted areas in experimental teeth. The corresponding areas were also examined with scanning electron microscope(x70) The results are as follows. 1. Minerals were detected in order of Ca, P, Mg and Na. In all root surfaces, levels of Ca and P were higher in dentin than in cementum. 2. Level of Mg was twice as high in dentin than in cementum. There was no significant difference in the level of Mg and Na between normal and periodontal diseased roots or between the various locations in the same root. 3. Level of Ca and P in the surface cementum showed no difference between normal and periodontal diseased root, although the areas in dentin with high level of either ion also showed high level of corresponding ion in cementum. 4. Difference in the Ca and P content between various locations within the same root was noted, although no coherent pattern existed. These results suggest that although the mineral content of the root cementum in periodontitis-affected tooth is affected by exogenous ions from saliva and food, but there was no difference in the mineral contents between normal and periodontally diseased root.

• Journal of the Korean Electrochemical Society
• /
• v.3 no.2
• /
• pp.100-103
• /
• 2000

Polymeric gel electrolytes based on polyacrylronitile blended with poly(vinylidene fluoride-co-hexafluoro-propylene)(P(VdF-co-HFP), which were reinforced with glass fiber cloth(GFC) to increase the mechanical strength, were prepared for the practical use in secondary battery. Test cell consisting of $LiCoO_2$ as a cathode and mesophase pich-based ca.bon fiber (MCF) as an anode material showed a capacity of 110 mAh/g based on the cathode weight at 0.2C rate at room temperature. Over $80\%$ of initial capacity was retained after 400cycles, indicating that GFC is suitable for a reinforcing material to increase the mechanical strength of gel based electrolytes.