• The Plant Pathology Journal
• /
• v.28 no.4
• /
• pp.446-452
• /
• 2012

The effect of heavy metals on seedling growth and pigment levels was studied in Arabidopsis using essential (Cu, Mn, and Zn) and non-essential metals (Pb and Hg). Generally increasing the concentrations of the metals resulted in a gradual decrease in root and shoot lengths, a decrease in chlorophylls, an increase in anthocyanins and a fluctuation in carotenoid content depending on the metal types. The toxicity of the metals decreased in the following order: Cu > Hg > Pb > Zn > Mn. Among the five metals, Cu was exceptionally toxic and the most potent inducer of anthocyanins. Pb induced the smallest quantity of anthocyanins but it was the strongest inducer of carotenoids. It suggests that the Cu-stressed Arabidopsis may use anthocyanins as its main antioxidants while the Pb-stressed Arabidopsis use carotenoids as its main protectants. All of the five metals induced an accumulation of anthocyanins. The consistent increase in anthocyanin content in the metal-stressed Arabidpsis indicates that anthocyanins play a major role in the protection against metal stresses.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.5
• /
• pp.338-345
• /
• 2002

The study presents a new testing and analysis method for brake judder on vehicle. For the identification of the excitation mechanism of a brake judder, it is necessary to measure the dynamic brake disc geometry during braking on vehicle. The non-contact sensor system was used to monitor the brake disc geometry. Brake torque variation (BTV) caused by disc thickness variation (DTV) is the primary excitation for brake judder. The mechanical effects generating BTV are linked not only to initial manufacturing tolerances but also to uneven wear. Therefore, the brake disc geometry should be strictly managed to initial condition. The aim of this study has been to measure the dynamic DTV and runout on vehicle and analyze the influence of test parameters on brake judder and compare the disc component with vehicle matching about the DTV Profile. As a result of this study, The amplitude of brake judder is proportional to vehicle speed and fluid pressure fluctuation on braking. The major sources of brake judder are directly related to disc thickness variation and side runout variation of corner assembly (disc, hub. bearing).

• Journal of the Korean Society of Industry Convergence
• /
• v.2 no.2
• /
• pp.91-102
• /
• 1999

The paper describes a robust adaptive control algorithm for induction motor drive without speed sensor at low speed range. The control algorithm use only current sensors in a space vector pulse width modulation within loop control with rotor speed estimation and voltage source inverter. On-line rotor speed estimation is based on utilizing parallel model reference adaptive control system. MRAC of the modified flux model for flux and rotor speed estimator uses dual-adaptation mechanism, ${\omega}_r$ and ${\omega}_e$ scheme. The estimated flux components in the model can be compensated from the effects of offset errors on pure integrals. It can be compensated to the parameter variations and torque fluctuation with speed estimation in less then 10 rad/sec. In a simulation, the proposed induction motor control algorithm without speed sensor at very low speed range are shown to operate very well in spite of variable rotor time constant and fluctuating load without change the controller parameters. The suggested control strategy and estimation method have been validated by simulation study, and it proposed the designed system for the implementation using TI320C31 DSP/ASIC controller.

• Korean Journal of Veterinary Research
• /
• v.27 no.1
• /
• pp.93-99
• /
• 1987

A study was conducted to observe the effects of dexamethasone sodium 21 phosphate injection in different amounts, intervals and times on the fluctuation of the parasitized erythrocytes in the peripheral blood of the T. sergenti carrier calves. A total of 31 calves including 15 Holstein and 16 Korean native male calves aged 6-12 months (125-300kg) was used. Results observed were as follows. 1. The calves injected 0.2mg/kg body weight two and three times in 48 hour intervals and 5 times in 24 hour intervals observed that 2 out of 2 heads, 3 out of 6 heads, and 4 out of 5 heads, respectively were substantially increased parasitized erythrocytes in the blood for 3-11 days after the first injection and continued to 2-10 days. 2. However, the calves injected once with 0.1mg/kg body weight and all control calves showed no visible change of the parasitized erythrocytes in the blood during the experimental period. 3. The animals injected over 2 times with 0.2mg/kg body weight tended to be decreased the number of erythrocytes, hemoglobin concentration and PCV for 2-3 days after first injection and continued about one week. 4. All animals injected the dexamethasone were observed the neutrophilic leukocytosis, eosinopenea and lymphopenea until 48 hours after injection.

• Korean Journal of Microbiology
• /
• v.21 no.1
• /
• pp.7-14
• /
• 1983

In order to study the effects of cropping system and fungicide (Dachigaren) on soil microbes, the seasonal fluctuations of soil microbes in the fields of radish and Chinese cabbage including soil pH, Soil moisture content and soil temperature were investigated on every 15 day interval from the begining of March to late October in 1981. The population of total fungus peaked at the begining of July, while that of total bacteria, at the begining of August. They were affected by soil temperature, however pathogenic microbes seemed to be more related with host plants than the soil temperature, because pathogens showed high density through the whole cultivation period. The pathogenic microbes showed the density of order ; Xanthomonas, Erwinia, Pseudomonas, Agrobacterium and Corynebacterium. Xanthomonas, Erwinia and Pseudomonas, which induced radish and Chinese cabbage diseases were higher than Agrobacterium and Corynebacterium in population densigy. Bacterial soft rot occured at the density of Erwinia $5.9{\sim}6.6{\times}10^5/dry$ soil 1 gram. The density of microbes on continuous fields were higher than that of rotating fields, but there were no significant difference between treated fungicide plot and non treated in the density of microbes, also no difference between Chinese cabbage and radish growing fields.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.5
• /
• pp.35-41
• /
• 2005

The effects of cooled-ECR on the characteristics of combustion and exhaust emissions were investigated in a single cylinder HCCI diesel engine The premixed charge (gasoline or diesel) was obtained with premixing chamber and high-pressure (5.5MPa) injection system. Exhaust pressure control and cooled ECR system were used in order to reduce pressure fluctuation and to mix the exhaust gas well with the fresh intake air. The experimental results show that NOx emissions from conventional diesel engine are steeply decreased by HCCI diesel combustion with cooled-EGR in both case of gasoline and diesel premixing. But soot emissions are rapidly increased with the increase of ECR rate. The recycled exhaust gas increased the ignition delay of mixture and decreased maximum combustion pressure. HC and CO emissions of HCCI combustion are increased with ECR rate.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.10 no.1
• /
• pp.1-9
• /
• 1990

Tillering of orchardgrass during establishment year was considered as an important factor for ground cover and forage yield. Field experiment was conducted to examine seasonal fluctuation of tiller number in three cultivars of orchardgrass; Potomac, Hall-mark, and Sumas, after transplanting with five planting density. Also, effects of plant density and nitrogen application in cultivar, Potomac were studied on tillering, forage yield and various growth characteristics in pot experiment Tillers per plant decreased with increased density and showed seasonal variations. It increased up to July, decreased during summer months, and increased again from October. Sumas had less tillers than other cultivars, especially at high density. Tillers per unit area kept high during spring. After then, there was stady decrease through summer and remained constant without affecting by planting density. Nitrogen application increased tillers per unit area in Potomac up to 20kg/10a, but decreased its tiller production at 40kg/lOa. Maximum number of tiller was obtained in the combinations of 20kg application of nitrogen with higher density than 324 plant per square meter. Forage yield increased as nitrogen application increased, while it did not respond to plant density. Forage yield had high linear correlation between LAI, leaf number with a peak at 2800 culrns. For high forage yielding, it was suggested to obtain optimum number of tillers per unit area in early season as possible, applying of adequate amount of nitrogen with relative high density depend on cultural condition.

• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.1
• /
• pp.19-27
• /
• 2015

In the present study, an effort was made to numerically investigate rectangular cavity aeroacoustics with and without doors. The simulation was performed on an open cavity with an aspect ratio of 5:1:1 at Mach 0.85 using the delayed detached eddy simulation (DDES) approach based on the Spalart-Allmaras model. Two cavity configurations, a clean cavity and a cavity with doors, were modeled. The results obtained from the clean cavity were compared with the experimental sound pressure levels (SPL) and the root mean square for the pressures applied. Furthermore, comparisons of frequencies were made using a modified semi-empirical Rossiter formula. The simulation using DDES precisely predicted the pressure fluctuation and the results matched the experiment quite well. The SPLs at the rear of the cavity were much higher than those in the front due to the instability of the shear layer impinging on the rear wall. Comparisons of DDES for the clean cavity and the doors-on cavity revealed that the SPLs inside the cavity as well as the magnitude of tones are amplified by the side doors. The main focus of this investigation was to obtain a better understanding of the open cavity acoustic resonance phenomenon and investigate the effects of cavity doors on the SPL.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05b
• /
• pp.127-129
• /
• 2005

We investigated the fault current limiting characteristics according to the various facilities in power system. Power systems are becoming larger and larger for meeting electric power demand. Therefore, the over-currents resulting from contingencies such as short circuits are increasing higher, which causes the ratings of circuit breakers(CBs) to increase. Upgrading or replacement of CBs is not difficult from the technical and economical point of view. Bus split is being adopted into a part of 154 kV power systems, but it has adverse effects such as overload to neighboring power systems, increased voltage fluctuation, and decreased power system stability. For 345 kV power systems, the bus split measure is not feasible and dc reactors are being suggested. The superconducting fault current limiter is a protection gear of new concept that limits fault current automatically in a few milliseconds. It can also provide the effect of CB capacity increase, relaxation of power machine criteria, enhancement in power system reliability, and flexible power system operation.

• Nuclear Engineering and Technology
• /
• v.46 no.4
• /
• pp.513-520
• /
• 2014

In this paper, three types of operational and industrial absorbers used at research reactors, including Ag-In-Cd alloy, $B_4C$, and Hf are selected for sensitivity analyses. Their integral effects on the main neutronic core parameters important to safety issues are investigated. These parameters are core excess reactivity, shutdown margin, total reactivity worth of control rods, thermal neutron flux, power density distribution, and Power Peaking Factor (PPF). The IAEA 10 MW benchmark core is selected as the case study to verify calculations. A two-dimensional, three-group diffusion model is selected for core calculations. The well-known WIMS-D4 and CITATION reactor codes are used to carry out these calculations. It is found that the largest shutdown margin is gained using the $B_4C$; also the lowest PPF is gained using the Ag-In-Cd alloy. The maximum point power densities belong to the inside fuel regions surrounding the central flux trap (irradiation position), surrounded by control fuel elements, and the peripheral fuel elements beside the graphite reflectors. The greatest and least fluctuation of the point power densities are gained by using $B_4C$ and Ag-In-Cd alloy, respectively.