• Wind and Structures
• /
• v.22 no.1
• /
• pp.43-63
• /
• 2016

In conventional buffeting theory, it is assumed that the aerostatic coefficients along a bridge deck follow the strip assumption. The validity of this assumption is suspect for a cable-stayed bridge in the construction stages, due to the effect of significant aerodynamic interference from the pylon. This situation may be aggravated in skew winds. Therefore, the most adverse buffeting usually occurs when the wind is not normal to bridge axis, which indicates the invalidity of the traditional "cosine rule". In order to refine the studies of static wind load on the deck of cable-stayed bridge under skew wind during its most adverse construction stage, a full bridge 'aero-stiff' model technique was used to identify the aerostatic loads on each deck segment, in smooth oncoming flow, with various yaw angles. The results show that the shelter effect of the pylon may not be ignored, and can amplify the aerostatic loading on the bridge deck under skew winds ($10^{\circ}-30^{\circ}$) with certain wind attack angles, and consequently results in the "cosine rule" becoming invalid for the buffeting estimation of cable-stayed bridge during erection for these wind directions.

• Steel and Composite Structures
• /
• v.49 no.1
• /
• pp.1-17
• /
• 2023

Based on Ahmadzadeh-Varvani hardening rule (A-V model), multiaxial ratcheting effect of Z2CND18.12N austenitic stainless steel is simulated by ABAQUS with user subroutine UMAT. The results show that the predicted results of the origin multiaxial A-V model are lower than the experimental data, and it is difficult to control ratcheting strain rate. In order to improve the predicted capability of A-V model, the A-V model is modified. In this study. Moreover, under the assumption of the von Mises yield criterion and normal plasticity flow rule, we develop a numerical algorithm of plastic strain with the improved model to implement the finite element calculation of the model. Internal iteration in the numerical algorithm was implemented with the Euler backward method, which calculated the trial strain for each equilibrium iteration using the consistent tangent matrix. With a user subroutine, the proposed model is programmed into ABAQUS for a user - executable version. By simulating the uniaxial ratcheting of a round bar made of Z2CND18.12N austenitic stainless steel, we observe that the predicted results simulated by ABAQUS with UMAT are compared with the experimental data. The predicted results of the improved multiaxial A-V model are consistent well with the experimental data.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.47 no.2
• /
• pp.190-197
• /
• 2024

By the recent fast growth of e-commerce markets, it has been stimulated to study order picking systems to improve their efficiency in distribution centers. Many companies and researchers have been developed various types of order picking systems and pursued the corresponding optimal operation policies. However, the performances of the systems with the optimal policies often depend on the structures of the centers and the operation environments. Based on a simulation model that mimics a unique zone picking system operated by a real company in the Republic of Korea, this study compares several operation policies and finds the most appropriate order selection rule and worker assignment policy for the system. Under all scenarios considered in this study, simulation results show that it is recommendable to assign more efficient workers to the zones with heavier workload. It also shows that selecting the order with the maximum number of non-repeatedly visited zones from the order list provides the most consistent and stable performances with respect to flow time, makespan, and utilization of the system even under the scenario with the breakdown zones. On the other hand, selecting the order with the minimum ratio of penalty to the number of zones performs the worst in all scenarios considered.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.47 no.4
• /
• pp.281-289
• /
• 2011

The purpose of this study is to identify the flow resistance of the bottom trawl net. The bottom trawl net being used in the training ship of Chonnam National University was selected as a full-scale net, and model nets such as 1/10, 1/25 and 1/50 of the actual net were made. Total resistance of the net part, the height of the net mouth and the flow resistance of components of the net such as wing, bag and cod-end part was measured, converted into full-scale and compared. Additionally, the model rule of Tauti (1934), which has been most frequently used in fishing net modeling experiments, was applied to interpret flow resistance and scale effect of model experiment was investigated. Presumed that the flow resistance R is $R=kS{\upsilon}^2$ against the flow velocity of each net ${\upsilon}$, resistance coefficient k was calculated by substituting R, ${\upsilon}$ and S of the net. From the result, it was found that k decreases exponentially when u increases which makes $k=c{\upsilon}^{-m}$. Whereas m of each net is ranged between 0.13-0.16 and there was not significant difference between nets. c does not show big difference in 1/10 and 1/25 model and the value itself was relatively bigger than in 1/50 model. The height of the net mouth of 1/25 and 1/50 model net h decreases exponentially according as ${\upsilon}$ increases to make $h=d{\upsilon}^{-n}$. Whereas d and n values were almost same in two nets. Additionally, when resistance of cod-end, wing and bag part in 1/25 and 1/50 model nets, both nets showed big resistance in bag part when flow is 1m/s as more than 60%. Wing and cod-end part showed almost same value or wing part had little bit larger value. On the other hand, when reviewing the reasons why both models showed difference in 1/50 model while c value against the resistance coefficient k did not show big difference in 1/10 and 1/25 model, it is inferred that the difference occurred not from material difference but from the difference in net size according to scale. It was judged that they are the scale effects concomitant to the model experiments.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.767-772
• /
• 2006

The SWTR(Surface Water Treatment Rule) requires achieving removal 99.9% Giardia and 99.99% Virus. To remove Giardia and Virus, disinfection process is essential process. CT is important index for Disinfection performance. CT value is expressed by CXT. C is represented by disinfection concentration and T is represented by $T_{10}$ which means 90% contact time in clearwell. To improve Disinfection performance, it is desirable to increase $T_{10}$. Primary factor affected $T_{10}$ is flow Pattern. Because guide wall change that flow pattern is uniform, we have installed guide wall to increase $T_{10}$. In this paper, we have performed numerical analysis for clearwell installed symmetric guide wall and center divided guide wall using CFD. We have analyzed flow pattern and $T_{10}$ in each clearwell. And. we compare symmetric guide wall with center divided guide wall in flow pattern and $T_{10}$.

• Journal of the Korea Safety Management & Science
• /
• v.6 no.1
• /
• pp.219-228
• /
• 2004

We can be acquire the conformation about on the due date of supplier by using the A TP(A vail able to Promise) function of management about real and concurrent access on the supply chain, also decide the affect about product availability due to forecasting or customer's orders through the A TP. Under the these environments, defines the A TP rule that can improve the customer value and data flow related the LTV(Life Time Value) and builds on a algorithm. In this paper, It consolidates the necessity on a LTV (Life Time Value) and analyzes data which is concerned of Customer Value. Under the these environments, defines the LTV rule that can improve the customer value. And then, Scheduling plays an important role in shop floor planning. Therefore, this study tries to proposed that Scheduling by customer needs group for minimizing the problem.

• Journal of the Korea Society of Computer and Information
• /
• v.9 no.4 s.32
• /
• pp.49-54
• /
• 2004

Rule-based access control can not completely be replaced by identity-based access control. Neither can role-based access control be a merger of identity-based access control and rule-based access control, but can be used complementarily for each other. In this paper, is proposed a simulation model designed for a new integrated access control method that has been created by means of integrating the existing access control methods. The integrated access control method is equipped with security, integrity and flow control and can easily accomodate the requirements for access control from role-based corporate bodies. The simulation model proposed in this paper can be applied for real working system designs.

• Proceedings of the KSRS Conference
• /
• 2008.10a
• /
• pp.266-269
• /
• 2008

Urban is more intelligent continuously with the help of the convergence with IT technology. And it requires an integrated control system, which can manage urban facilities or monitor large-scale events based on GIS data, to provide its citizen with various ubiquitous services such as u-Health, u-Traffic, context-awareness etc. In order to realize the intelligent city geo-sensors that have the functionalities of generic sensing as well as location awareness will be established everywhere in the near future. Our system we presented have a rule engine to handle a atomic event as well as complex events that contain control flow or branch among them. And it can allow for visualization and monitoring the results through KML (Keyhole Mark-up Language) in the Google Maps. This paper describes au-GIS event processing system that can deal effectively with u-GIS events coming from various geo-sensor data in ubiquitous computing environments.

• Journal of Korea Multimedia Society
• /
• v.8 no.9
• /
• pp.1269-1281
• /
• 2005

The control of character's behavior in games is determined by game designers. One of the popular method used in the control of character's behaviors is rule-based. The rule-based control of behavior makes the flow of play simple and boring. In this paper, we propose an efficient method of controling character's behaviors which can generate various actions of characters by using probability estimation applied to the character's behaviors.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.10
• /
• pp.217-224
• /
• 1999

Trouble shooting of modern machine tools equipped with sophisticated electronic as well as mechanical parts is so difficult that it is usually depends upon the experience and accumulated knowledge of the diagnosing persons. On the other hand, tool users are scattered in wide area, which makes it expensive for a machine tool maker to run a vast service network. An unmanned diagnosis system to which users can have access at all times could be an efficient alternative. For this purpose, a rule-based expert system for diagnosing machine tools is developed. This paper describes the structure of diagnostic knowledge, the rule firing mechanism, the diagnosis flow, and user query process. An example shows the feasibility of problem solving on site without help of a service expert from machine tool maker.