• Journal of Electrical Engineering and Technology
• /
• v.9 no.1
• /
• pp.1-5
• /
• 2014

When renewable sources are connected to the distribution network in the form of a distributed generators(DGs), the effect of intermittent output appears as voltage fluctuation. The surplus power at the consumer ends results in the reverse power flow to the distribution network. This reverse power flow causes several problems to the distribution network such as overvoltage. Application of the reactive power control equipment and power flow control by means of BTB inverter have been suggested as the general solutions to overcome the overvoltage, but they are not economically feasible since they require high cost devices. Herein, we suggest the feeder loop line switch control method to solve the problem.

• International Journal of Aeronautical and Space Sciences
• /
• v.2 no.1
• /
• pp.1-11
• /
• 2001

The time implicit point SGS scheme is applied to compute hypersonic viscous flows in thermochemical nonequilibrium. The performance of the point SGS scheme is then compared with those of the line SGS and the LU-SGS schemes. Comparison of convergence histories with the effect of multiple forward and backward sweeps are made for the flow over a 2D cylinder experimentally studied by Hornung and the flow over a hemisphere at conditions corresponding to the peak heating condition during the reentry flight of an SSTO vehicle. Results indicate that the point SGS scheme with multiple sweeps is as robust and efficient as the line SGS scheme. For the point SGS and the LU-SGS scheme, the rate of improvement in convergence is largest with two sweep cycles. However, for the line SGS scheme, it is found that more than one sweep cycle deteriorates the convergence rate.

• KSBB Journal
• /
• v.17 no.4
• /
• pp.339-344
• /
• 2002

Flow injection analysis technique for monitoring of xylitol concentrations in biological processes has been developed using xylitol oxidase (XYO) immobilized on VA-Epoxy Biosynth carrier. The immobilized XYO cartridge has been integrated into a FIA system with an oxygen electrode and systematically investigated with regards to the factors which can affect the activity of the immobilized XYO, such as pH, temperature, salt concentration etc. The activity of the immobilized XYO increased with the temperature ($19.0 - 29.0^{circ}C$) and sample injection volume ($75-250\muL$) and molarity of potassium phosphate buffer (0.1-1 M), but it reached the highest value at pH 8.5. The XYO-FIA system has been also applied for on-line monitoring of xylitol concentrations in a reactor and showed good operational stability and agreement with off-line data measured with HPLC.

• Proceedings of the KIEE Conference
• /
• 2001.11b
• /
• pp.239-242
• /
• 2001

This paper presents a windows program package for solving security constrained OPF in interconnected power systems, which is based on the combined application of evolutionary programming(EP) and sequential quadratic programming(SQP). The objective functions are the minimization of generation fuel costs and system power losses. The control variables are the active power of the generating units, the voltage magnitude of the generator, transformer tap settings and SVC setting. The state variables are the bus voltage magnitude, the reactive power of the generating unit, line flows and the tie line flow. In OPF considering security, the outages are selected by contingency ranking method. The resulting optimal operating point has to be feasible after outages such as any single line outage(respect of voltage magnitude, reactive power generation and power flow limits). The OPF package proposed is applied to 10 machines 39 buses model system.

• Journal of Drive and Control
• /
• v.11 no.4
• /
• pp.32-38
• /
• 2014

The hydraulic fuse, which responds to the suddenly increased flow on rupture of a line and shuts off the fluid flow, would prevent large spillage of liquid. The quick-acting hydraulic fuse, which is mainly composed of a poppet, a seat, and a spring, must be designed to minimize the leaked flow and to prevent high collision speed between the poppet and seat during fuse operation on a line rupture. The optimal design parameters of a quick-acting hydraulic fuse were searched using the genetic algorithm and the complex method that are kinds of constrained direct search methods. The dynamic behavior of a quick-acting hydraulic fuse was researched using computer simulations that applied the obtained optimal design parameters.

• Proceedings of the KIEE Conference
• /
• 2003.07a
• /
• pp.569-571
• /
• 2003

As a definition of NERC, Available Transfer Capability(ATC) is a measure of the transfer capability remaining in the physical transmission network for the future commercial activity. To calculate ATC, accurate and defensible TTC, CBM and TRM should be calculated in advance. In this paper, we propose a method to quantify TRM using probabilistic load flow based on the method of moment. Generation output, bus voltages, loads, and line outages are considered as complex random variables (CRV) to take into account for uncertainties related to the transmission network conditions. Probability Density Function (PDF) of line flow at the most limiting line is used to quantify TRM with the desired probabilistic margin. Suggested method is compared with the results from conventional CPF method and verified using 24 bus MRTS, and the suggested method based on PLF shows efficiency and flexibility for the quantification of TRM compared with the conventional method.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.505-506
• /
• 2006

This study is focused on the manufacturing technique of powder injection molding of watch case made from zirconia powder. A series of computer simulation processes were applied to the prediction of the flow pattern in the inside of the mould and defects as weld-line. The material properties of melted feedstock, including the PVT graph and thermal viscosity flowage properties were measured to obtain the input data to be used in a computer simulation. Also, a molding experiment was conducted and the results of the experiment showed a good agreement with the simulation results for flow pattern and weld line location. On the other hand, gravity and inertia effects have an influence on the velocity of the melt front because of the high density of ceramic powder particles during powder injection molding in comparison with polymer's injection molding process. In the experiment, the position of the melt front was compared with the upper gate and lower gate positions. The gravity and inertia effect could be confirmed in the experimental results.

• Nuclear Engineering and Technology
• /
• v.53 no.1
• /
• pp.322-336
• /
• 2021

This paper presents a numerical prediction of the transient hydraulic loads acting on the tubes and external supports of a pressurized water reactor (PWR) steam generator (SG) during blowdown following a sudden feedwater line break (FWLB). A simplified SG model was used to easily demonstrate the prediction. The blowdown discharge flow was treated as a flashing flow to realistically simulate the transient flow fields inside the SG and the connected broken feedwater pipe. The effects of the SG initial pressure or the broken feedwater pipe length on the intensities or magnitudes of transient hydraulic loads were investigated. Then predictions of the decompression pressure wave-induced impulsive pressure differential loads on SG tubes and the transient blowdown loads on SG external supports were demonstrated and the general aspects of transient responses of such transient hydraulic loads to the FWLB were discussed.

• Journal of Korean Society of Forest Science
• /
• v.101 no.2
• /
• pp.291-296
• /
• 2012

Triploids are a useful tool for biomass production and molecular breeding of trees with a long life span. Triploids of the poplar 'Hyunsasi' (Populus alba ${\times}$ P. glandulosa) have been developed by crossing between female diploids and a male tetraploid. The tetraploid was developed around the 1970s at Korea Forest Research Institute by colchicine-induced chromosome doubling. Seedlings of the $F_1$ generation were analyzed using flow cytometry to verify their ploidy status. The mean relative fluorescence index of 3 F1 poplars, labeled as Line- 1, Line-17, Line-18, were approximately 1.5 times higher than those of diploid poplars, and the results clearly indicated that they were triploids. The phenotype of the F1 poplars included larger leaves and thicker stem than diploids, and abnormal leaf morphology, especially in the triploid 'Line-18'. Three triploid lines developed roots more slowly and had less roots than diploid. However, 3 poplar cytotypes (2x, Line-1, Line-17) rooted within 10 days on MS medium. In contrast, compared with the 3 cytotypes, the Line-18 showed about 80% and 70% in the rooting rate and the number of roots. The triploid poplars could be directly utilized for biomass production and with their sterility, they could serve as basic material for genetic transformation. In addition, flow cytometric analysis proved to be an effective and reliable method for screening forest trees for their ploidy level.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.11a
• /
• pp.403-408
• /
• 1996

The subchannel analysis was performed to verify the behavior of hot channel characteristics and obtain the information to support the core thermal-hydraulic behavior at post-trip steam line break with low flow condition. During this postulated accident, buoyancy-induced cross flow occurs, and the coupled nuclear and thermal-hydraulic interactions become important. The code predictions with TORC are in good agreement with the test data. Under such conditions, the mass flow increase in the hot channel by buoyancy-induced cross flow depends on the parameter $GR^{*}\;/\;Re^2$, and buoyancy effect becomes more noticeable as $GR^{*}\;/\;Re^2$ increases.