• International Journal of Highway Engineering
• /
• v.19 no.6
• /
• pp.175-182
• /
• 2017

PURPOSES : Road sectors contribute approximately 16 % of total GHG emission rates in South Korea. Engineers and experts expend significant efforts to identify countermeasures for the reduction of carbon emission. This study aims to determine how total carbon emission rates change depending on whether or not there is speed limit enforcement. METHODS : In this study, Lamm's travel speed profile theory is first adopted to select the hazard road, which sections are designated as speed limit enforcement. Second, Motor Vehicle Emission Simulator (MOVES) was used to simulate the carbon emission on the road. RESULTS : The total carbon emission rate under speed limit enforcement was 10,773 g higher than the condition without speed limit enforcement in the designated road. This might affect acceleration, which can lead to increased emissions. CONCLUSIONS : There would be no researches about proving the relationship how speed limit enforcement has an effect on carbon emission. The result of our study can provide valuable guidelines regarding road safety and eco-friendly roads.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.2
• /
• pp.156-161
• /
• 2007

A set of experiments of counter-current flow limit (CCFL) was performed to improve the drawbacks of Wallis' correlation which neglected the effects of channel size, channel length, injection method and the boundary conditions at the inlet of liquid and gas phase. In this study, CCFL was observed by changing the shape of porous plate using air and water. The results show that as the size of porous increases, CCFL with a round shape of the porous plate start to disappear, In this study, the CCFL correlation was calculated and the corresponding CCFL map was developed based on the experimental results.

• Transactions of Materials Processing
• /
• v.24 no.4
• /
• pp.227-233
• /
• 2015

In this paper, the effect of flow stress, friction, temperature, and velocity on finite element predictions of metal flow lines after cylindrical upsetting is presented. An actual three-stage hot forging process involving an upsetting step is utilized and experimental metal flow lines are measured to study the effect of the various process variables. It was found that temperature and velocity for reasonable values of friction have little influence on metal flow lines especially those located deep within the cylinder but that flow stress has a direct influence on the flow lines. It was shown that a pure power law material model cannot reflect the real flow stress of hot material because it underestimates the flow stress especially around the dead-metal zone for the upsetting of a cylindrical specimen. It is thus recommended that a proper lower limit of flow stress be assumed to alleviate this issue.

• Structural Engineering and Mechanics
• /
• v.36 no.5
• /
• pp.529-544
• /
• 2010

Nonlinear equations of structures are generally solved numerically by the iterative solution of linear equations. However, this iterative procedure diverges when the tangent stiffness is ill-conditioned which occurs near limit points. In other words, a major challenge with simple iterative methods is failure caused by a singular or near singular Jacobian matrix. In this paper, using the Newton-Raphson algorithm based on Davidenko's equations, the iterations can traverse the limit point without difficulty. It is argued that the propose algorithm may be both more computationally efficient and more robust compared to the other algorithm when tracing path through severe nonlinearities such as those associated with structural collapse. Two frames are analyzed using the proposed algorithm and the results are compared with the previous methods. The ability of the proposed method, particularly for tracing the limit points, is demonstrated by those numerical examples.

• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.6
• /
• pp.1298-1307
• /
• 2001

Recently, the efforts to improve fuel economy and to reduce pollutant emission have become the main subject in the development of a gasoline engine. A lean combustion engine admitted as the best alternative is relatively lower fuel consumption rate and exhaust emissions. In this study, it is focused on intensifying intake flow field as one of methods to improve the performance of the lean combustion. First, three different types of suitable swirl control valve(SC7) with high swirl and tumble ratio are selected through steady flow experiment, being installed in a spark ignition engine. The relationship between lean misfire limit and torque was investigated with injection timing and spark ignition timing. Also, the effect of intensified swirl new on the combustion Stability and exhaust emissions was experimently examined by the measuring in-cylinder pressure and combustion variation. The results show that the engine with swirl control calve is superior to other conventional engine on the lean misfire limit, specific torque, combustion variation and emission, and the appropriate injection timing and spark ignition timing exist according to the type of swirl control valve.

• Journal of Environmental Science International
• /
• v.4 no.1
• /
• pp.91-103
• /
• 1995

The reaction rate, equilibrium, and flow injection analysis methods were fundamentally evaluated for the determination of aqueous ammonia. The selected indophenol blue method was based on the formation of indophenol blue in which ammonium ion reacted with hypochlorite and phenol in alkaline solution. In the optimized reaction condition, the reaction followed 1st order reaction kinetics and the final product was stable. The absorbance measurements before and after the equilibrium were utilized for the reaction rate and equilibrium methods. The reaction rate methods, based on the relative analytical signals for the possibility of eliminating interferents, were shown to have good linear calibration curves but the detection limit and the calibration sensitivity were poorer than those in the equilibrium method. The detection limits were 32-49 pub and 24 pub for the reaction rate and equilibrium methods, respectively In the flow injection analysis, the absorbance was measured before the equilibrium reached and thus resulted in 30% reduction of calibration sensitivity. However, the detection limit was 11 ppb, indicating that the peak-to-peak noise for the blank was remarkably improved. Compared to the manual methods, the optimized experimental condition in a closed reaction system reduced the blank absorbance and the inclusion of ammonia from the atmosphere was prevented. In addition, highly reproducible mixing of sample and reagents and analytical data extracted from continuous recording showed excellent reproducibility.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.2
• /
• pp.156-165
• /
• 2014

This paper is the first investigation on the effect of flow control methods on the part load performance in a spark ignition engine. For comparison of the methods, two control devices, port throttling and masking, were applied to a conventional engine without any design change of the intake port. Steady flow evaluation shows that steady flow rates per unit opening area and swirl ratio are very low compared with the port throttling and saturated from mid-stage valve lift, however, swirl increases slightly as the lift is higher in case of 1/4 masking control. In the part load performance, the effect of simple port throttling on lean misfire limit expansion is limited and insufficient; on the other hand a masking improves the limit considerably without any port modification for increasing swirl. Also the results show that the intake flow control improves the combustion with following two mechanisms: stratification induced by the combination of the flow pattern and the fuel injection timing attribute to ignition ability and the intensified flow ensure fast burn. In addition fuel consumption reduces under the flow controls and the reduction rate is different according to the operation conditions and control methods. At the Stoichiometric and/or low speed and low load the throttling method is more advantageous; however vice versa at lean and high load condition. Finally, the throttling is more efficient for HC reduction than masking, on the other side the NOx emissions increase under the masking and decrease under the port throttling compared with conventional port scheme.

• Korea-Australia Rheology Journal
• /
• v.14 no.2
• /
• pp.77-86
• /
• 2002

A microscopic theoretical study is performed to predict the rheological properties of human blood in the low concentration limit. The shear thinning behavior of blood in the low shear limit is studied by considering the aggregate formation of red blood cells, which is called the rouleaux formation. Then the constitutive equations of blood in the high shear limit are derived for various flow situations by considering the unique features of deformation of blood cells. Specifically, the effects of the surface-area-preserving constraint and the lank-treading motion of blood cells on the rheological properties are studied.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.213-216
• /
• 2009

In order to see the flame behavior in the gas turbine combustor, combustion test was performed by using sector combustor. Ignition test with torch ignition system was carried out at the various combustor inlet velocity and air fuel ratio. Also, flame blow out limit was measured by changing fuel flow rate with fixed air mass flow rate. In the test results, stable ignition is possible at air excess ratio of 6 and this limit is gradually increased with combustor inlet air velocity. The minimum blow out limit is about 4 at 40 m/s of combustor inlet velocity. This blow out limit is also increased up to about 10 with increasing combustor inlet velocity.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.1
• /
• pp.308-322
• /
• 1991

A set of experiments of Counter-Current Flow Limit(CCFL or Flooding) was performed to improve the drawbacks of Wallis' Correlation which neglects the effects of channel size, channel length, injection method and the boundary conditions at the inlet of liquid and gas phase. In these experiments using water and air, the followings were found ; (i) The effects of channel size and length were quite significant. In large tubes(D>20mm), the flooding front occurred at the bottom of the channel and when the gas flow increased the front moved upward ; however, in small tubes(D<20mm), there were no upward movement of flooding front and the flooding just occurred at the liquid inlet. (ii) The effect of water inlet device was not as significant as that of channel length though the inlet boundary conditions could affect the flow development and flooding afterward. (iii) Once the flooding front reached the inlet of water injection device, an newly reduced flow condition was set up and resulted in another flooding corresponding to the new condition.