• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.6
• /
• pp.697-704
• /
• 2004

Bifurcation behavior of ignition and extinction of catalytic reaction is theoretically investigated in a stagnation-point flow. Considering that reaction takes place only on the catalytic surface, where conductive heat losses are allowed to occur, activation energy asymptotics with a overall one-step Arrhenius-type catalytic reaction is employed. For the cases with and without the limiting reactant consumption, the analysis provides explicit expressions, which indicate the possibility of multiple steady-state solution branches. The difference between the solutions with and without reactant consumption is in the existence of an upper solution branch, and the neglect of reactant consumption is inappropriate for determining extinction conditions. For larger values of reactant consumption, the solution response is all monotone, suggesting that multiple solutions are not possible. It is shown that bifurcation Damkohler numbers increase (decrease) with increasing of conductive heat loss (gain) on the catalytic surface, which means that smaller (larger) values of the strain rate allow the surface reaction to tolerate larger heat losses (gains). Lewis number of the limiting reactant can also significantly affect bifurcation behavior in a similar way to the effect of heat loss.

• Aerospace Engineering and Technology
• /
• v.7 no.2
• /
• pp.162-169
• /
• 2008

Dynamic characteristics of a control valve, which plays an important role in thrust control of liquid rocket engines, have been analysed by AMESim simulator modeling. A speed control method has been proposed for the control of the valve equipped with a BLDC motor and the performances of this control method have been proved in making a comparison between the predictions of simulation and experimental results. Moreover, it is shown that a control valve with a second pre-filter is enough stable to the flow disturbances. The speed control method for BLDC motor is more simpler than PI gain scheduling method for the application in complex flow system.

• Journal of Biosystems Engineering
• /
• v.34 no.5
• /
• pp.331-341
• /
• 2009

A double-end rod hydraulic cylinder is widely used with a steering valve for the steering control system in large tractors. For the development of automatic steering controller, the feasibility of using a proportional control valve replacing the conventional manual steering valve to control the position of hydraulic steering cylinder was investigated in terms of the max. overshoot, the steady-state error and the rise time. A simulation model for the electrohydraulic steering system with load using AMESim package was developed to be valid so that the proper control algorithm could be chosen through the computer simulation. It could be concluded that the P-control algorithm was sufficient to control the electrohydraulic steering system, where the control frequency should be no greater than 20 Hz at the P-gain of 5. In particular, the performance of the developed steering controller was satisfactory even at the conditions of varying flow rates and loads.

• The Journal of Asian Finance, Economics and Business
• /
• v.7 no.3
• /
• pp.9-15
• /
• 2020

This paper investigates how economic freedom affected firm investment in Vietnam. In the globalization decade, economic freedom has been an important policy to support economic development in Vietnam. Improvements in economic freedom, such as capital freedom and domestic credit freedom, allow firms to access external finance more easily, so that the firm's investment depends less on internal cash flow. In a developing country, on the drawbacks, many small and medium firms likely have more challenges if the government would not give any subsidies. The higher level of freedom may exacerbate the financing constraints of less competitive firms. We analyze unique firm-level data from 2006 to 2016, which includes listed firms on two major stock exchanges and unlisted firms in the Unlisted Public Company Market. The article also considers how economic freedom affects small firms and large firms differently. Our results show that capital freedom and domestic credit freedom played an important role in investments for Vietnamese firms. However, we cannot find evidence that overall economic freedom relaxed the financial constraints on firms. Additionally, we suggest that small firms likely gain more advantage in access to external finance than do larger firms when the government removes restrictions from capital movement and the domestic credit market.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.6 no.4
• /
• pp.380-387
• /
• 1994

An experimental study was performed to investigate the characteristics of refrigerant flow rate control and superheat in an evaporator with an electronic expansion valve(EEV). The EEV used in this study was devised using a needle valve coupled with a stepping motor controlled by a personal computer. A Pill control equation was used to control the superheat of the evaporator and to set the superheat to $5^{\circ}C$. In order to determine an optimum running condition for the system, Pill parameters were varied for the wide range of values. The running condition of an air conditioning system with a PI control was reasonably stable compared with that of the Pill control. Experimental results for the PI control using parameter values, $K_p=1.5$, $T_i=400(sec)$ and $T_s=6(sec)$ show that the superheat reached its target value. When external disturbances were introduced to the system, the superheat target value was reached within about 3 minutes. When the EEV was applied to the air conditioning system driven by an inverter, room temperature control was excellent.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.1256-1261
• /
• 2009

Seawater amounts to 70% of the earth and represents a quite unlimited resource for the production of fresh water by desalination processes and for the extraction of dissolved salts present in it. Recently, the falling film evaporation has increased in interest as an efficient method for seawater desalination system. In the desalination system, the flow characteristics of the falling film is very important issue to make highly efficient system. So, this study is taken to investigate numerically the falling film thickness on the inlet Renold Number ranges are 400 to 700. Numerical simulations are performed using FLUENT6.3.26, a commercial CFD code.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.7
• /
• pp.948-955
• /
• 2003

Pressure coefficient in rotating discharge hole was measured to gain insight into the influence of rotation to the discharge characteristics of rotating discharge hole. Pressure measurements were done by the telemetry system that had been developed by the authors. The telemetry system measures static pressure using piezoresistive pressure sensors. Pressure coefficients in rotating discharge hole were measured in longitudinal direction and circumferential direction with various rotating speed and 3 pressure ratios. From the results, the pressure coefficient, and therefore the discharge coefficient, is known to decrease with the increase of Ro number owing to the increase of flow approaching angle to the discharge hole inlet. However, there exists critical Ro number where the decrease rate of discharge coefficient with the increase of Ro number changes abruptly; flow separation occurs from the discharge hole exit at this critical Ro number. Critical Ro number increases with the increase of length-to-diameter ratio, but the increase is small where the length-to-diameter ratio is higher than 3. The decrease rate of discharge coefficient with the increase of Ro number depends on the pressure recovery at the discharge hole, and the rate is different from each length-to-diameter ratio; it has tendency that the short discharge hole shows higher decrease rate of discharge coefficient.

• Journal of ILASS-Korea
• /
• v.22 no.2
• /
• pp.62-68
• /
• 2017

It is important to study on the combustion instability to develop liquid rocket engines for preventing lower combustion efficiency and destruction of combustion chamber. There are many researches on simplex injector with liquid pulsation to solve this problem. In real rocket engine system, however, they use coaxial injectors. Therefore, research on coaxial injector with liquid pulsation is essential. In this study, we investigate dynamic characteristics of gas centered swirl coaxial injector varying tangential inlet diameter. A mechanical pulsator was used to generate an excitation in the liquid flow, and the response characteristics of the injector were confirmed. As tangential inlet diameter increased, mass flow rates increased and spray angle decreased. As tangential inlet diamter decreased, gain decreased because the pressure fluctuation in the injector manifold rarely passed through the inlet. Additionally, it was confirmed that a sufficiently small tangential inlet served as a damper.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.18 no.4
• /
• pp.488-493
• /
• 2008

A mathematical model of molten steel level for continuous casting process is presented, where the molten steel level, input and output flow in the mold, the relation between stopper position and input flow etc. are considered. The mathematical model is implemented and simulated by using MATLAB. Comparing the result of molten steel level from the simulator with that of real plant, the performance of the model is shown to be reasonable. By using this simulator, it is shown that PI controller with variable P gain, adjusted by fuzzy logic system, has better control result than conventional PI controller.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.31 no.4
• /
• pp.307-325
• /
• 1995

IN order to gain a fundamental data for forecast or control of fish behavior and evaluated the feasibility of an application of the modeling technique to a field, in this paper a numerical model for describing the behavior of fishes in a water tank was presented. The parameters of the model were estimated by using the time-series data on the three-dimensional position of fishes and by applying the least squares algorithm. The estimated parameters were standardized to examine the variation of parameters according to the number of individuals and flow speed that the mean values of parameters were to be zero and their variances were to be one. The results obtained can be summarized as follows: (1) The standardized parameter $a^*$of propulsive force decreased according to increased the number of individuals and the flow speed. (2) The standardized parameter ${k_b}^*$ of interactive force increased according to increased the number of individuals, but decreased according to the flow speed. (3) The standardized parameter ${k_c}^*$ of schooling force increased according to │increased the number of individuals and the flow speed. (4) The standardized parameter │${k_w}^{+*}$│ of repulsive force against wall or bottom increased according to increased the number of individuals, but decreased according to the flow speed. (5) The standardized parameter │${k_w}^{-*}$│ of attractive force against wall or bottom was generally constant according to increased the number of individuals, but increased according to the flow speed. (6) The standardized parameter $\upsilon$ super(*) of damping force increased according to increased the number of individuals, but decreased according to the flow speed.