• Transactions of Materials Processing
• /
• v.21 no.3
• /
• pp.186-194
• /
• 2012

Hot stamping is a forming method that offers various advantages such as superior mechanical properties, good formability, and very small springback. However, relatively large-sized parts, such as front pillars, exhibit poor formability when hot stamped due to the limited material flow and thickness reduction imparted by the process. This reduction in thickness can also lead to cracks. One of the reasons is the relatively high friction between the sheet and the die. In this study, in order to obtain the optimal conditions for hot stamping of front pillars, various process parameters were studied and analyzed using the sheet forming software, J-STAMP. The effects of various parameters such as the die structure, blank shape, blank holding force, punch speed, clearance(upper and lower dies) and distance block were analyzed and compared.

• Journal of Power Electronics
• /
• v.3 no.1
• /
• pp.17-23
• /
• 2003

A new three-phase soft-switching active front-end inverter is presented. The topology consists of a quasi-resonant PWM boost converter with an additional resonant branch, which provides low loss at high frequency operation. This leads to a high conversion efficiency and a remarkable reduction in the siBe of the input inductor. To synchronise the PWM pattern with the resonance cycle, a modified space vector modulation with asymmetrical PWM pattern is used. A high power factor can be achieved for both power flow directions. Due to a new control strategy the converter features a low content of harmonics in the line currents even for distorted line voltages.

• Journal of the Korean Society of Safety
• /
• v.13 no.3
• /
• pp.119-125
• /
• 1998

In long vertical duct, the aspect of second flame in laminar flame propagating through lycopodium-air mixtures and the behavior of dust particles in neighborhood in front of flame have been examined experimentally. In order to trace the development of second flame to its origin, the velocity and vorticity distribution of dust particles in front of flame were measured by using with the real-time PIV system. The velocity of particles was approximately zero at the central part of flame front and the ahead of the flame leading edge, but maximum near the duct wall. The flame velocity of second flame and the movement of leading flame edge depend mainly on behavior of dust particles by the flow distribution of temperature and pressure.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.146-150
• /
• 2001

A new three-phase soft-switching active front-end inverter is presented. The topology consists of a quasi-resonant PWM boost converter with an additional resonant branch, which provides low loss at high frequency operation. This leads to a high conversion efficiency and a remarkable reduction in the size of the input inductor. To synchronise the PWM pattern with the resonance cycle, a modified space vector modulation with asymmetrical PWM pattern is used. A high power factor can be achieved for both power flow directions. Due to a new control strategy the converter features a low content of harmonics in the line currents even for distorted line voltages.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.111-114
• /
• 2005

Experimental and numerical studies were carried out in order to investigate the processability and the transcriptability of the injection molding of micro structures. For this purpose, we designed a mold insert having micro rib patterns on a relatively thick base part. Mold insert has a base of 2mm thickness, and has nine micro ribs on that base plate. Width and height of the rib are $300{\mu}m\;and\;1200{\mu}m$, respectively. We found a phenomenon similar to 'race tracking', due to 'hesitation' in the micro ribs. As the melt flows, it starts to cool down and melt front located in the ribs near the gate cannot penetrate further because the flow resistance is large in that almost frozen portion. When the base is totally filled, the melt front away from the gate is not frozen yet. Therefore, it flows back to the gate direction through the ribs. Consequently, transcriptability of the rib far from the gate is better. We also verified this phenomenon via numerical simulation. We further investigated the effects of processing conditions, such as flow rate, packing time, packing pressure, wall temperature and melt temperature, on the transcriptability. The most dominant factor that affects the flow pattern and the transcriptability of the micro rib is flow rate. High flow rate and high melt temperature enhance the transcriptability of micro rib structure. High packing time and high packing pressure result in insignificant dimensional variations of the rib. Numerical simulation also confirms that low flow rate causes a short shot of micro ribs and high wall temperature helps the filling of the micro ribs.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.7 no.2
• /
• pp.153-160
• /
• 1983

The flows in an axial flow turbomachine are calculated numerically in the two sets of flow surfaces of H-S and B-B surfaces assuming that the flow is axisymmetric. The calculation is performed by regarding the governing equations as the quasi-Poisson's equations and using the finite element method for the flow regions divided into triangular elements. The results of numerical calculation agree comparatively well with the experimental results and it has been found that the distribution of an axial velocity component at the rotor exit is not necessarily uniform under the influences of the inlet guide vanes and the front shape of the hub even if the rotor is designed by the free-vortex theory. Also it has been found that the existence of the optimum value of the blade number can be estimated from the results of calculation of deviation angles at rotor exit if we consider the viscous flow-loss, and that the flows of B-B surfaces are affected very sensitively by the degree of satisfaction of Kutta condition.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.6
• /
• pp.82-90
• /
• 1999

Numerical analysis of the three dimensional flow in a bus engine room is carried out through this study. The radiator and the fan modeling rare carried out to simulate the flow in an engine room, and the results are focused on the flow in the cavity located in front of the radiator. The numerical simulation results are compared with the experiment . To improve the cooling performance in the bus engine room, the flow inside the cavity is inspected in detail. The complex flow features are found in this region , and the suggestion are made to improve the radiators cooling performance.

• Journal of the korean society of oceanography
• /
• v.38 no.3
• /
• pp.143-155
• /
• 2003

Current and sea level were observed in spring 1999 by a bottom mounted ADCP and tide gauge in the central part of the South Sea of Korea. With respect to the front, the distribution of isotherms is prograde in the offshore region whereas that of isohalines is retrograde, especially in the coastal area. The combined effect results in shoaling of isopycnals at the front. This distribution corresponds to a westward coastal flow on the northern side of the front and the eastward Tsushima Warm Current (TWC) to the south, determined by vessel-mounted ADCP observations. The low-frequency current shows either alternating clockwise-counterclockwise rotation or else persistent eastward motion depending on the frontal motion. Fluctuations of wind, sea level and current are coherent at period of 3-4 days and show some characteristics of Ekman-like dynamics.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.12 no.4
• /
• pp.107-114
• /
• 2016

Recently, 3D related technology has become a hot topic for IT. 3D technologies such as 3DTV, Kinect and 3D printers are becoming more and more popular. According to the flow of the times, the goal of this study is that the general public is exposed to 3D technology easily. we have developed a web-based application program that enables 3D modeling of facial front and side photographs using a mobile phone. In order to realize 3D modeling, two photographs (front and side) are photographed with a mobile camera, and ASM (Active Shape Model) and skin binarization technique are used to extract facial height such as nose from facial and side photographs. Three-dimensional coordinates are generated using the face extracted from the front photograph and the face height obtained from the side photograph. Using the 3-D coordinates generated for the standard face model modeled with the standard face as a control point, the face becomes the face of the subject when the RBF (Radial Basis Function) interpolation method is used. Also, in order to cover the face with the modified face model, the control point found in the front photograph is mapped to the texture map coordinate to generate the texture image. Finally, the deformed face model is covered with a texture image, and the 3D modeled image is displayed to the user.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.30 no.6
• /
• pp.1044-1055
• /
• 1997

To find out generating mechanism of eddies in the polar frontal zone of the East Sea, we carried out a series of numerical experiments using the nonlinear $1^{1/2}-layer$ model allowing the effect of the polar front. We assumed the polar front at about $39^{\circ}N$ in zonal direction with the cold water region in the northern part and the warm water region in the southern part of the model ocean. To examine the effect of the frontal motion without the influence of the Tsushima Current from the beginning of the geostrophic adjustment, the initial state of the model ocean was assumed motionless. Eastward current was caused by the geostrophic adjustment process in the polar frontal zone that induced a steady northward coastal current along the Korean coast to satisfy the mass continuity. The overshooting of this coastal current acted as an initial disturbance of the zonal flow field which caused meanders and eddies. The spatial scales of eddies were in good agreement with the baroclinic instability theory.