• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.644-648
• /
• 2004

In the present study were examined numerically and experimentally the off-design performance characteristics on an axisymmetric plug nozzle with variable throat area. In this nozzle concept, its throat area can be changed by translating the plug into the axial direction. First, a mixed-expansion plug nozzle, in which two expansion parts are arranged both inside and outside, was designed by means of the method of characteristics. Second, the CFD analysis was verified by the cold-flow wind tunnel test. Third, its performance characteristics were evaluated over a wide range of pressure ratio from half to double throat area through the design point, using the CFD code verified by the wind tunnel tests. It was made clear from the study that not so critical thrust efficiency losses were found and the maximum thrust efficiency loss was at most approximately 5 % under off-design conditions without external flow. This result shows that a plug nozzle can give the altitude compensation even under off-design geometry operations. However, shock waves were observed in the inner expansion part under the doubled throat area operation and thus some thermal problems may be caused on the plug surface. Furthermore, collapse of cell structure on the plug surface was observed with external flow (around Mach number 2.0) as it became lower pressure ratio below the design point and the fact may result in big efficiency loss regardless of geometrical configuration.

• Wind and Structures
• /
• 제22권2호
• /
• pp.253-272
• /
• 2016

The paper concerns with the method and results of wind tunnel investigations of the Strouhal number (St) of a stationary iced cable model of cable-supported bridges with respect to different angles of wind attack. The investigations were conducted in the Climatic Wind Tunnel Laboratory of the Czech Academy of Sciences in $Tel{\check{c}}$. The methodology leading to the experimental icing of the inclined cable model was prepared in a climatic section of the laboratory. The shape of the ice on the cable was registered by a photogrammetry method. A section of an iced cable model with a smaller scale was reproduced with a 3D printing procedure for subsequent aerodynamic investigations. The St values were determined within the range of the Reynolds number (Re) between $2.4{\cdot}10^4$ and $16.5{\cdot}10^4$, based on the dominant vortex shedding frequencies measured in the wake of the model. The model was oriented at three principal angles of wind attack for each of selected Re values. The flow regimes were distinguished for each model configuration. In order to recognize the tunnel blockage effect the St of a circular smooth cylinder was also tested. Good agreement with the reported values in the subcritical Re range of a circular cylinder was obtained. The knowledge of the flow regimes of the airflow around an iced cable and the associated St values could constitute a basis to formulate a mathematical description of the vortex-induced force acting on the iced cable of a cable-supported bridge and could allow predicting the cable response due to the vortex excitation phenomenon.

• 반도체디스플레이기술학회지
• /
• 제10권2호
• /
• pp.39-44
• /
• 2011

In this study, we have investigated the structural and electrical characteristics of IZO thin films deposited on flexible substrate for the OLED (organic light emitting diodes) devices. For this purpose, PES was used for flexible substrate and IZO thin films were deposited by RF magnetron sputtering under oxygen ambient gases (Ar, $Ar+O_2$) at room temperature. In order to investigate the influences of the oxygen, the flow rate of oxygen in argon mixing gas has been changed from 0.1sccm to 0.5sccm. All the samples show amorphous structure regardless of flow rate. The electrical resistivity of IZO films increased with increasing flow rate of $O_2$ under $Ar+O_2$. All the films showed the average transmittance over 85% in the visible range. The OLED device was fabricated with different IZO electrodes made by configuration of IZO/a-NPD/DPVB/$Alq_3$/LiF/Al to elucidate the performance of IZO substrate. OLED devices with the amorphous-IZO (a-IZO) anode film show better current density-voltage-luminance characteristics than that of OLED devices with the commercial crystalline-ITO (c-ITO) anode film. It can be explained that very flat surface roughness and high work function of a-IZO anode film lead to more efficient hole injection by reduction of interface barrier height between anode and organic layers. This suggests that a-IZO film is a promising anode materials substituting conventional c-ITO anode in OLED devices.

• 한국수자원학회논문집
• /
• 제44권6호
• /
• pp.477-486
• /
• 2011

본 연구는 인공수로 또는 인공호수와 같은 환경 친화적 친수공간이 건설됨에 따라 발생되는 수질오염 문제를 수질모형실험을 통해 해소할 수 있는 방법을 연구하였다. 호소수의 개념으로 도입되는 인공수로 및 호수는 제한된 수량 공급으로 인해 수질악화, 악취발생 및 녹조 현상이 일어날 수 있다. 하지만, 이러한 현상을 예상할 수 있는 방법은 수치해석으로만 의지해 왔고 물리적 해석에 의한 검증이 이뤄지지 않아 실제 적용에 대한 어려움이 있었다. 따라서 본 연구에서는 오염된 물과 오염되지 않은 물이 서로 희석되어 영양염류의 농도를 낮추는 현상에 착안하여 원형과 모형의 상사에 영향을 받지 않는 무차원의 물리적 수질모형실험을 실시하였다. 또한 수체 내에서 흐름을 인공적으로 발생시키는 흐름유발기기의 효과 검증과 적용방법을 연구하여 목표수질을 유지할 수 있는 방안을 제시하였다.

• 한국융합학회논문지
• /
• 제6권2호
• /
• pp.37-42
• /
• 2015

오늘날 지구는 환경오염이 심해짐에 따라 여러 가지 자연 재해 때문에 실제 사용할 수 있는 수자원이 점차 고갈되어 가고 있어 그 수자원을 절약할 수 있는 방법이 필요한 때이다. 본 연구는 욕실용 수전 모델들의 내부에서의 유동 해석을 하여 속도 및 온도 분포들을 분석하였다. Model 3가 Model들 중 혼합 후의 온도가 가장 균일하게 나타나고, Model 3는 가장 낮은 속도 분포를 가지고 있고 혼합을 위한 공간이 가장 커서 물의 배출속도에 가장 많은 영향을 줌으로서 물을 아낄 수 있다고 보인다. 본 연구 결과를 이용하여 여러 가지 모양의 공간을 만들어 더욱 혼합이 잘 이루어지게 하여 그 물을 아끼는 욕실용 수전 모델의 개발에 활용될 수 있다고 사료된다. 또한, 디자인 면에서 융합 기술로의 접목도 가능하여 미적인 감각을 나타낼 수 있다.

• 한국수소및신에너지학회논문집
• /
• 제33권5호
• /
• pp.534-540
• /
• 2022

Liquid hydrogen has the best storage capacity per unit mass and is economical among storage methods for using hydrogen as fuel. As the demand for hydrogen increases, the need to develop a storage and supply system of liquid hydrogen is emphasizing. In order to liquefy hydrogen, it is necessary to pre-cool it to a maximum inversion temperature of -253℃. The Gifford-McMahon (GM) refrigerator is the most reliable and commercialized refrigerator among small-capacity cryogenic refrigerators, which can extract high-efficiency hydrogen through liquefied hydrogen production and boil of gas re-liquefaction. Therefore, in this study, the optimal conditions for liquefying gas hydrogen were sought using the GM cryocooler. The process was simulated by PRO/II under various cooling capacities of the GM refrigerator. In addition, the flow rate of hydrogen was calculated by comparing with specific refrigerator capacity depending on the pressure and flow rate of a refrigerant medium, helium. Simulations were performed to investigate the optimal values of the liquefaction flow rate and compression pressure, which aim for the peak refrigeration effect. Based on this, a liquefaction system can be selected in consideration of the cycle configuration and the performance of the refrigerator.

• Journal of Ceramic Processing Research
• /
• 제13권spc2호
• /
• pp.260-264
• /
• 2012

We have investigated the effect of ambient gases on the structural, electrical, and optical characteristics of IZO thin films intended for use as anode contacts in the organic light emitting diodes (OLED) devices. These IZO thin films were deposited on the PES film by radio frequency (RF) magnetron sputtering under different ambient gases (Ar, Ar + O2, and Ar + H2) at room temperature. In order to investigate the influences of the ambient gases, the flow rate of oxygen and hydrogen in argon has been changed from 0.1 sccm to 0.5 sccm, respectively. All the IZO thin film has an (222) preferential orientation regardless of ambient gases. The electrical resistivity of the IZO film increased with increasing O2 flow rate, whereas the electrical resistivity decreased sharply under an Ar + H2 atmosphere and was nearly similar regardless of the H2 flow rate. The change of electrical resistivity with changes in the ambient gas composition was mainly interpreted in terms of the charge carrier concentration rather than the charge carrier mobility. All the films showed the average transmittance over 85% in the visible range. The OLED device was fabricated with different IZO substrates made with the configuration of IZO/α-NPD/DPVB/Alq3/LiF/Al in order to elucidate the performance of the IZO substrate. The current density and the luminance of OLED devices with IZO thin films deposited in 0.5 sccm H2 ambient gas are the highest amongst all other films.

• Journal of Korean Neurosurgical Society
• /
• 제66권4호
• /
• pp.382-392
• /
• 2023

Objective : The use of indocyanine green videoangiography (ICG-VA) to assess blood flow in the brain during cerebrovascular surgery has been increasing. Clinical studies on ICG-VA have predominantly focused on qualitative analysis. However, quantitative analysis numerical modelling for time profiling enables a more accurate evaluation of blood flow kinetics. In this study, we established a multiple exponential modified Gaussian (multi-EMG) model for quantitative ICG-VA to understand accurately the status of cerebral hemodynamics. Methods : We obtained clinical data of cerebral blood flow acquired the quantitative analysis ICG-VA during cerebrovascular surgery. Varied asymmetric peak functions were compared to find the most matching function form with clinical data by using a nonlinear regression algorithm. To verify the result of the nonlinear regression, the mode function was applied to various types of data. Results : The proposed multi-EMG model is well fitted to the clinical data. Because the primary parameters-growth and decay rates, and peak center and heights-of the model are characteristics of model function, they provide accurate reference values for assessing cerebral hemodynamics in various conditions. In addition, the primary parameters can be estimated on the curves with partially missed data. The accuracy of the model estimation was verified by a repeated curve fitting method using manipulation of missing data. Conclusion : The multi-EMG model can possibly serve as a universal model for cerebral hemodynamics in a comparison with other asymmetric peak functions. According to the results, the model can be helpful for clinical research assessment of cerebrovascular hemodynamics in a clinical setting.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.55-60
• /
• 2004

In this study, the configuration and tension of a towing cable for side-scan sonar are predicted in an ambient flow and at an unsteady towing condition. The governing equation of three-dimensional dynamic analysis for a flexible cable is solved using a finite difference method. We successfully predict the configuration and tension of a side-scan sonar and designed the towing system. It is found in static analyses that the side-scan sonar must be towed to keep a its stable depth at a reasonable speed. The study also reveals in the transient analyses that the dominant component affecting the top tension is the tangential drag force for the larger towing speed than the critical speed, and the self weight of a towed instrument for the smaller towing speed than. It should be maneuvered for a towing vessel with good consideration for the impact effect in a cable due to tension peak when a towing speed is suddenly increase. The developed program can be applicable for three-dimensional dynamic analysis of a towing system for various marine survey instruments.

• 대한토목학회논문집
• /
• 제32권6C호
• /
• pp.267-274
• /
• 2012

오염물질의 거동은 간극 배열과 연결망에 의해 결정되지만 흙에서 오염물질의 이동을 계산하는 전통적인 접근은 거시 스케일에서 적용된다. 나비에-스토크스 방정식을 풀기 위해 소요되는 컴퓨팅 비용 때문에 간극 스케일에서 이동과 결과를 관찰하기 쉽지 않다. 본 논문에서는 단일상 다성분 유체유동에서 국부적인 유속과 밀도를 효과적으로 평가할 수 있는 격자 볼츠만 방법에 대해 설명한다. 오염물질의 시공간적 거동은 유체 유동의 이송에 의해 명시적으로 결정된다. 두 가지 형태의 이상화된 간극은 유체의 경로를 제공한다. 또한 오염물질 이동, 유속장, 오염물질의 평균 농도는 정상상태의 유동에서 계산된다. 굴곡비와 같은 간극 형상은 오염물질 거동의 영향을 준다. 이는 흙이나 암반의 불연속면에서 동일한 간극률를 가져도 간극의 배열과 형상의 중요함을 강조한다.