• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.2
• /
• pp.69-79
• /
• 1997

This paper deals with the measurement and analysis on the scavenging performance of the oppet-valve type two-stroke engine with different shroud system. The scavenging flow characteristics is investigated by flow visualization under steady condition, in which a dye is introduced into single-cycle method using the difference of specific gravity between two working fluids is used to evaluate the scavenging efficiency and the trapping efficiency. The 90° shroud system was found to be the highest efficiency system through both flow visualization and single-cycle test, as well as the shroud system to generally be efficient for reducing a short-circuiting flow during scavenging process in a two-stoke engine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.1-10
• /
• 2002

As the preliminary stage for the countermeasure of thermal loading in miller cycle engine, coolant flows in the cylinder head of base engine including exhaust valve bridge were visualized and analyzed by using PIV technique. It was found that low coolant velocity regions were around exhaust valve bridge, around which stagnation of the coolant flow was observed due to the complex geometry configuration of water jacket. And velocity variation between each cylinder was remarkable. For the countermeasure of these, it is necessary to enhance coolant flow around exhaust valve bridge and to improve the deviation of coolant flow between each cylinder.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.11 no.3
• /
• pp.332-338
• /
• 1999

An experimental study of absorption phenomena of water vapor into LiBr solution was carried out to find out the optimum solution flow rate. The staggered bundle of horizontal absorption tubes, which are the same configuration as the commercial heat pump, were tested. The results showed that the heat transfer and absorption rate were enhanced with the increase of LiBr solution flow rate. Those values for different absorber pressures showed the same qualitative trends. The optimum flow rate of solution was obtained as three times of the designed flow rate.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.9
• /
• pp.20-25
• /
• 2010

This paper mainly proposes power flow algorithm using OOP(Object-Oriented Programming) in distribution power system. Because the most power system problems are calculated from power flow, it is an important part in power system. Recently, new power generation facilities are steadily installed in the distribution system connected with Microgrid which has been gaining popularity among the industry and utilities. This paper contributes to improve the power flow algorithm using OOP for efficient power flow according to the distribution system configuration fluctuated frequently.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.11
• /
• pp.3022-3030
• /
• 1995

The irreversibility of condensation process in the supersonic flow of steam turbine cascade causes the entropy to increase and the total pressure loss to be generated. In the present study, in order to investigate the moist air flow in two dimensional steam turbine cascade made as the configuration of the last stage tip section of the actual steam turbine moving blade, the static and total pressures along suction side of the blade are measured by pressure taps and Pitot tube. The flow field is visualized by a Schlieren system. The effects of stagnation temperature and the degree of supersaturation on energy loss and entropy change in the flow are clearly identified.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.1
• /
• pp.102-111
• /
• 2001

To describe the air flow characteristics within an air cleaner cover and mass air flow sensor (MAFS) entry region installed in a 3.0L engine air induction system, flow visualization, velocity and turbulence intensity measurements were taken in several view planes. A detailed knowledge of the interaction between the design parameters and the flow structures will enhance our understanding of the motions within the flow field and enable engineers to optimize the induction system and reduce the signal-to-noise ratio in the MAFS output. Emphasis is placed on the analysis of coherent motions and the controlling parameters which affect the air flow in the MAFS entrance region over a flow rate of 13-240 kg/hr. The high speed motion pictures illustrated that the air flow generated within the air cleaner cover under steady state condition is quite complex. In both axial and radial planes of the main passage it was found that the flow pattern is remarkably influenced by the air cleaner cover and main passage configuration. A comparison of the flow patterns and measurements in the original and modified air cleaner cover is presented. Measurements from the MAFS indicated an significant reduction in pressure drop and signal noise for the modified cover as compared with the original cover, over an air flow rate of 13-240 kg/hr.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.1
• /
• pp.9-15
• /
• 2011

In this study, we investigated the hydrodynamic and thermal performance of constructal architectures on the basis of the mass flow rates for a given pressure drop, and we determined the thermal resistance and flow uniformity. The five flow configuration used in this study were the first construct with optimized hydraulic diameter, the second construct with optimized hydraulic diameter, the first construct with non-optimized hydraulic diameter, second construct with non-optimized hydraulic diameter, and a serpentine configuration. The results of our study suggest that the best fluid-flow structure is the second constructal structure with optimized constructal configurations. We also found that in the case of the optimized structure of cooling plates, the heat transfer was remarkably higher and the pumping power was significantly lower than those of traditional channels.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.7
• /
• pp.717-722
• /
• 2011

The aim of this study is to identify the locations at which local wall thinning occurs and to determine the turbulence coefficients related to local wall thinning. Experiments and numerical analyses of the tee sections of different down-scaled piping components were performed and the results were compared. Numerical analyses of full-scale models of actual plants were performed in order to simulate the flow behaviors inside the piping components. In order to determine the relationship between the turbulence coefficients and the rate of local wall thinning, numerical analyses of the tee components in the main feedwater systems were performed. The turbulence coefficients obtained from the numerical analyses were compared with the local wear rate obtained from the measurement data. From the comparison of the results, the vertical flow velocity component (Vr) flowing to the wall after separating in the wall due to the geometrical configuration and colliding with the wall directly at an angle of some degree was analogous to the configuration of local wall thinning.

• Journal of the Korean Society of Safety
• /
• v.30 no.6
• /
• pp.78-84
• /
• 2015

In order to increase the utilization of limited space in urban area, it can be a good solution to make use of underground space. For the last few decades, underground space systems, such as underground passages, subway stations, and underground shopping arcades, have been constructed in many cities all over the country. Despite of the advantages on the utilization of space in urban area, underground space systems have always been exposed to the risk of inundations resulted from severe rain storms. In this study, it has been examined to apply 2-D flow models (TUFLOW and FLUMEN) to establishing the preventive measures to the risk of flood. For the part with relatively complex configuration, such as a corridor junction, 2-D flow models present the detailed information about the effect of geometry on the inundation events and the temporal and spatial distribution of inundation over the space. From the result, it can be concluded that the 2-D flow model can be the effective implement for establishing the proper measure to the inundation on underground space systems, which generally have relatively long and narrow geometry with complex inner configuration.

• Environmental Engineering Research
• /
• v.17 no.2
• /
• pp.83-88
• /
• 2012

Currently, the technology of $CO_2$ capture and storage (CCS) has become the main issue for climate change and global warming. Among CCS technologies, the prediction of $CO_2$ behavior underground is very critical for $CO_2$ storage design, especially for its safety. Hence, the purpose of this paper is to model and simulate $CO_2$ flow and its heat transfer characteristics in a storage site, for more accurate evaluation of the safety for $CO_2$ storage process. In the present study, as part of the storage design, a micro pore-scale model was developed to mimic real porous structure, and computational fluid dynamics was applied to calculate the $CO_2$ flow and thermal fields in the micro pore-scale porous structure. Three different configurations of 3-dimensional (3D) micro-pore structures were developed, and compared. In particular, the technique of assigning random pore size in 3D porous media was considered. For the computation, physical conditions such as temperature and pressure were set up, equivalent to the underground condition at which the $CO_2$ fluid was injected. From the results, the characteristics of the flow and thermal fields of $CO_2$ were scrutinized, and the influence of the configuration of the micro-pore structure on the flow and scalar transport was investigated.